Spectrum Industries 22860 User manual

Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
1. Place the worksurface face-down onto a non-abrasive surface.
2. Align the legs with the mounting holes, and install (2) #14 x 1-3/4”
PHSM screws into each leg but do not tighten completely yet.
Figure 1.
0191978 Page 1 of 4
Assembly InstructionsAssembly Instructions
(4) 026064
1/4-20 x 5/8” PHMS
1. Attach legs to worksurface1. Attach legs to worksurface
Figure 1
(1) 025069
Glide wrench
The side of the leg with
the threaded hole should
be on the ip-top side
(1) 036281
Dual unit-to-unit
bracket
Flip-top
Worksurface
#14 x 1-3/4” PHSM
(2 per leg)
(1) 052463
Unit-to-unit bracket
(2) 026011
1/4-20 x 2” FHMS
(1) 052547 - Right Leg
(1) 052544 - Left Leg
(1) 0152133
44”W x 30”D
Worksurface w/ support
(1) 052469
Chair rail
(1) 052468
44” Cord channel /
Modesty panel
Esports Evolution Desk (44”W)
22860
(4) 037779
5/16-18 x 1”
Glide
(4) 0101381
#14 x 1-3/4” PHSM
(4) 0101382
#14 x 7/8” PHSM

0191978 Page 2 of 4
2. Install cord channel / modesty panel and glides2. Install cord channel / modesty panel and glides
1. Orient the modesty panel/cord channel as shown and attach to the
legs with (4) 1/4-20 x 5/8” PHM screws. Figure 2.1.
2. Install the (4) glides to the bottom of the legs. The glides can be
adjusted later to keep the desk level on uneven surfaces.
3. Tighten ALL screws.
Figure 2.1
Modesty panel /
cord channel
1/4-20 x 5/8” PHMS
(4 required)
Glides
(4 required)
The worksurface height can be adjusted from 24”H - 32”H in 1” increments.
Figure 2.2. Adjustment is easier when the desk is upside-down.
1. To adjust the legs, remove the (4) pre-installed adjustment screws.
(Fully-support the lower section of the leg while removing). Figure 2.3.
2. Choose a height and align the corresponding set of leg holes.
3. Install the (4) previously removed screws in the new holes and tighten securely.
4. Repeat this procedure on the second leg. Make sure to use the same set of
holes as used on the rst leg.
Figure 2.2 Figure 2.3
Lower section
Up to 8” of
adjustment
Up to 8” of
adjustment
Adjustment
screws
8”
24”
32”
Adjustable legsAdjustable legs

0191978 Page 3 of 4
3. Attach chair rail3. Attach chair rail
1. Carefully ip the desk upright-this will require at least two people.
2. Attach the chair rail with (2) 1/4-20 x 2” FHM screws as shown.
Note the chair rail should extend above the worksurface, and the
countersunk holes should be on the outside. Figure 3.1, 3.2.
3. Tighten all screws securely.
Figure 3.2
4. Connecting desks together (optional)4. Connecting desks together (optional)
Two desks can be connected together with the (2) included unit-to-unit brackets.
1. Locate the desks next to each other in their nal position.
2. Attach one of the narrow unit-to-unit brackets to the rear of the legs using
the existing leg screws (loosen leg screws to install, then re-tighten).
3. Attach the dual unit-to-unit bracket to both worksurfaces using (4) #14 x
7/8” PHSM screws.
4. Tighten all screws securely.
1/4-20 x 2” FHMS
(2 required)
Chair rail
Figure 4
Desk #1
Dual unit-to-unit bracket
(attach with four #14 x 7/8”
PHSM screws)
Narrow unit-to-unit bracket
(loosen screws to install,
then re-tighten)
Figure 3.1
1/4-20 x 2”
FHMS
Chair rail
Extends above worksurface
Desk #2

0191978 Page 4 of 4
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Warranty
1-800-235-1262
Toll-free HELPLINE
[email protected]
© 2020 Spectrum Industries Inc., All rights reserved.
We will make it right for you!
Thanks for choosing Spectrum! Spectrum is committed to provide complete customer satisfaction.
Each of our products is manufactured from the best materials available and each product is strin-
gently monitored throughout the production process through our P.A.C.E. program (Product Assur-
ance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from
defect for the period set out in the warranty from the date of delivery.
For a listing of all product specifi c warranty terms please visit our website at:
https://www.spectrumfurniture.com/en/resources/purchasing-terms-warranty