Spectrum Industries 55199 User manual

Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Assembly Instructions
Tools
Required
0119509R1 Page 1 of 3
Assembly Instructions
Customized Logo Panel
for Media Manager Elite
and Director Lecterns
55199
(6) 041943
1/4-20 locknuts
(1) 0118612
Logo Panel
Media Manager Elite (55258) Installation:
1. Open the document camera drawer fully to access the knobs
securing the audience-side panel. Figure 1A.
2. While keeping a hand on the audience-side panel, unscrew the
(2) knobs inside the lectern behind the panel and remove.
3. Carefully lift the panel out. Figure 1B.
4. To replace the panel, insert the panel tabs into the slots in the
base panel, then tip the panel back into position. Replace knobs,
and tighten securely.
Open document
camera drawer
Knobs Audience-side
panel
Slots in base panel
Figure 1A Figure 1B
Drill with
3/8” drill bit
7/16” or
adjustable
wrench
CAUTION
While removing the knobs, be sure to fully-support the audience-
side panel to prevent it from falling out of the lectern.

0119509R1 Page 2 of 3
5. Locate the (6) starter holes in the back of the audience-side panel. Figure 1C.
6. Using a 3/8” drill bit, slowly drill completely through the panel at the 6 hole locations.
7. Align the logo panel studs with the drilled holes and secure with (6) 1/4-20 locknuts. Figure 1D.
8. To re-install the audience-side panel, insert the panel tabs into the slots in the base panel, then
tip the panel back into position. Replace the knobs, and tighten securely.
Figure 1C Figure 1D
Removed
Audience-side
panel 1/4-20 locknuts
(6 required)
Logo panel
Removed
Audience-side
panel
Carefully drill through
the panel with a 3/8”
drill bit (6 holes total)
Use a sharp 3/8” drill bit to drill out the (4) existing starter holes.
Drill slowly to minimize laminate chip-out around the holes.
Placing masking tape on the laminate-side of the panel at the
hole locations before drilling will also help minimize chip-out.

0119509R1 Page 3 of 3
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Flip-up panel
Audience side
panel lock access
Figure 2A Figure 2B
Figure 2C
Audience-side
panel
1/4-20 locknuts
(6 required)
Logo panel
Removed
Audience-side
panel
1. Locate and ip-up the audience-side ip-up panel. Figure 2A.
2. Unlock the two panel locks.
3. Carefully lift out the audience-side panel. Figure 2B.
Director Lectern (55213) Installation:
4. Locate the (6) starter holes in the back of the audience-side panel. Figure 2C.
5. Using a 3/8” drill bit, slowly drill completely through the panel at the 6 hole locations.
6. Align the logo panel studs with the drilled holes and secure with (6) 1/4-20 locknuts. Figure 2D.
7. To re-install the audience-side panel, insert the panel tabs into the slots in the base panel, then
tip the panel back into position, and re-lock the locks.
Use a sharp 3/8” drill bit to drill out the (4) existing starter holes.
Drill slowly to minimize laminate chip-out around the holes.
Placing masking tape on the laminate-side of the panel at the
hole locations before drilling will also help minimize chip-out.
Figure 2D
Removed
Audience-side
panel
Carefully drill through
the panel with a 3/8”
drill bit (6 holes total)
Slots in base panel