Spectrum Industries InTouch 32 User manual

Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Any parts damaged during shipment must be reported
within 15 days of receipt. To report information regard-
ing missing parts or damage, to purchase parts or
accessories, or if you have any questions, please
contact us.
Thank you for purchasing Spectrum products!
Spectrum Industries, Inc
925 First Avenue, Chippewa Falls, WI 54729 USA
800 235 1262
715 723 6750
www.spectrumfurniture.com
Owner’s Manual
0114813R2 Page 1 of 7
InTouch 32™Secure Tablet Locker
55434

• Read this owner’s manual before assembly or operation.
• Do not allow children to operate.
• For indoor use only. Do not install or store where it will be exposed to moisture.
• Do not block the ventilation openings.
• Do not allow anyone to sit, stand, or climb on the unit.
• Use a damp, soft-cloth, or sponge, with mild soap or detergent solution to clean
dirty surfaces. Do not use harsh solvents or abrasives.
• This unit is intended for institutional use. It does not have any user-serviceable
parts or user-maintenance requirements. If servicing is necessary, please
contact Spectrum Industries for assistance.
Electrical Safety:
• Keep the power switches in the OFF position before plugging or unplugging
from the wall outlet.
• Turn OFF the devices before plugging them in.
• Ensure total device / equipment load does not exceed 12-amps.
• Do not plug the power cord into an extension cord.
• Inspect the power cords for damage before each use. Do not use power
cords that are damaged.
• Unplug power cord from electrical outlet by gripping the cord. Do not unplug
the power cord by pulling only on the cord.
• Do not step on, drive over, drag, or place objects on the power cord.
• For added safety, plug the cart into a grounded outlet controlled by a GFI
(Ground Fault Interrupter) circuit breaker.
• Damaged electrical components can create signi cant hazards to users and
is not covered by the warranty. Repairs should always be performed by a
quali ed electrician.
• Electrical devices are not toys. Children are often unaware of the hazards
associated with electrical devices. This unit must always be used by adults
or with adult supervision.
Warning - Relocating audio and/or video equipment to furniture not speci cally
designed to support audio and/or video equipment may result in death or
serious injury due to the furnishing collapsing or over turning onto a child.
Warning - Death or serious injury may occur when children climb on audio
and/or video equipment furniture. A remote control or toys placed on the
furnishing may encourage a child to climb on the furnishing and as a result the
furnishing may tip over on to the child.
0114813R2 Page 2 of 7
Important Safety and Care Instructions

0114813R2 Page 3 of 7
Figure 1B
The locker back panel has four 3/8” holes located 16” on-center
to match most stud-wall applications. Fasteners are not included.
(Cords from 16-outlet power units will route through bottom panel.)
1. Choose fasteners appropriate to the wall you will be anchoring to.
2. Determine the preferred wall location and height from oor.
3. Measure and mark the (4) hole locations on the wall. Figure 1B. Be sure fasteners will
be anchored securely to studs or other solid portion of the wall.
4. At the marked wall locations, drill holes appropriate to the chosen fastener type and size.
5. Support the locker (this may take 2-3 people), align the mounting holes, install fasteners,
and tighten to secure the locker to the wall. Figure 1C.
Four 3/8” holes are provided on the bottom panel to anchor the locker
to a worksurface for increased security. Fasteners are not included.
(Cords from 16-outlet power units will route through side panel).
1. Set the locker into its nal position. (If attaching to a table or worksurface,
be sure it is stable and sturdy enough to fully support the unit.)
2. Choose fasteners appropriate to the surface you will be attaching to. The
(4) mounting holes in the bottom panel are 3/8” dia. Figure 1A.
3. Mark the (4) hole locations through bottom panel.
4. At the marked locations, drill holes in the worksurface appropriate to the
chosen fastener type and size.
5. Install fasteners and tighten securely.
A. Worksurface anchoring
B. Wall-mounting
Figure 1A
WARNING
It is the customers responsibility to use appropri-
ate and adequate wall fasteners when attaching
the IT32 Tablet Locker to a wall. Nominal weight
of an empty IT32 is 76 lbs. Total loaded weight
will vary with quantity & types of tablets used.
(4) 3/8” holes
on back panel
Figure 1C
fasteners by
customer
3/8” holes for customer-
supplied fasteners
3/8” holes for
customer-supplied
fasteners
Assembly / Setup
IT32 tablet locker security

0114813R2 Page 4 of 7
route power cords
through divider panel
opening to tablets
side access panel
to power-side
(right-side)
Power-side wiring
Figure 2B
1. To gain access to the power-side, unlock & remove the side panel. Figure 2A.
2. Be sure both 16-outlet power units are unplugged and switched off.
3. Plug up to 32 tablet chargers into the power units. Figure 2B.
4. Route the charge cords through the upper & lower divider panel cutouts and into
the tablet storage area.
route power cords
through divider panel
opening to tablets
tablet chargers
16-outlet
power unit
tablet chargers
16-outlet
power unit
Figure 2A

0114813R2 Page 5 of 7
Figure 3A
Routing power cords to tablets
Figure 3B
Tablet power cords need to be 3’ or longer to use the recommended
cord management method shown in the wiring diagram below.
Figure 3A.
tablets
16-outlet power unit(s)
w/ tablet chargers
1. Use the cord management wraps above each tablet storage slot,
wrap excess cord while leaving enough cord length to drop down
to each tablet. Figure 3A-B.
cord
management
wraps

4mm hex
wrench
Tools
Required
0114813R2 Page 6 of 7
Figure 3C
2. Set tablets into slots. Figure 3C.
3. Plug charge cords into tablets.
4. Plug 16-outlet power units into wall outlets and switch on to begin charging.
Figure 4
Door stop adjustment
If necessary, the offset door stop can be rotated slightly to adjust
the closed position of the doors and lock rods.
1. To rotate, loosen the JC bolt slightly with a 4mm hex wrench. Figure 4.
2. Rotate the door stop until the door is positioned correctly.
3. Re-tighten the JC bolt securely.

Warranty Statement
0114813R2 Page 7 of 7
WE WILL MAKE IT RIGHT FOR YOU!
Spectrum is committed to provide complete customer satisfaction. Each of our products is manufactured from the best materials available and each
product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table
below from the date of delivery. This warranty shall not apply to defects or damage resulting from misuse, abuse, neglect, improper care, modication
or repair not authorized by Spectrum, or any other cause outside the control of Spectrum. Spectrum will, at its sole option, either repair or replace the
defective product.
This warranty is exclusive; no other warranty, written or oral, is expressed or implied. This warranty is given by Spectrum to Buyer and to no other per-
son or legal entity. No Spectrum dealer, distributor, agent or employee is authorized to make any modication or addition to this warranty.
NOTWITHSTANDING ANYTHING TO THE CONTRARY, SPECTRUM WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR INDIRECT OR
LIQUIDATED DAMAGES, INCLUDING CONSEQUENTIAL, INCIDENTAL AND SPECIAL DAMAGES. IN NO EVENT SHALL SPECTRUM’S LIABIL-
ITY, WHETHER UNDER CONTRACT OR WARRANTY, IN TORT OR OTHERWISE, EXCEED THE PURCHASE PRICE RECEIVED BY SPECTRUM
FOR THE PRODUCT AT ISSUE AND “RECALL ACTION” EXPENSES. SPECTRUM SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS
OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABIL-
ITY) OR OTHER THEORIES OF LAW, WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY SPECTRUM, OR ANY UNDERTAK-
INGS, ACTS OR OMISSIONS RELATING THERETO.
Our Customer Service Department is ready to provide immediate attention to any questions, comments or concerns. They are available to answer your calls
Monday through Friday from 7 am to 5 pm CST. In addition your product comments or concerns are welcome via e-mail at: [email protected].
Warranty Table
Item Warranty Period
• Adjustable Crank/Electric Desk Legs • 1 Year
• Flat Panel Desk Gas Cylinders
• Adjustable Height Chair Parts – including frames,
gas cylinders, wood and plastic parts, and control
handles Adjustable Height Chair Parts Casters
• Adjustable Height Chair Upholstery
• In-Stock Upholstery
• Graded-In Fabrics and Customer Owned Material
• 7 Years
• 2 Years
• 2 Years
• No Warranty
• Height Adjustable Columns and Lifts
• 1 Year
• General Use Casters
• Electrical
• Keyboard/Mouse Trays
• Flat Panel Monitor Arm – General Parts
• Flat Panel Monitor Arm – Gas Cylinders
• 5 Years
• 2 Years
• Computer Desk Chassis
• Cart Chassis
• Lectern Chassis
• 10 Years
925 First Avenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 800-235-1262, 715-723-6750 Fax: [phone]
E-mail: [email protected] web: www.spectrumfurniture.com