Spectrum Industries InVision 37102 User manual

0112776R4 Page 1 of 9
Assembly Instructions
Before you begin, please make sure all parts and proper quanti-
ties are included. Any parts damaged during shipment must be
reported within 15 days of receipt. To report information regarding
damages or if you have any questions, please call 1-800-235-1262.
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for purchasing Spectrum products!
InVision™Media Collaboration Table
48” x 60” - #37102
48” x 84” - #37103
60” x 60” - #37104
60” x 84” - #37105
Phillips screwdriver
glide wrench
(included)
4mm hex wrench
(included)
Tools Required
Note: The worksurface halves must be assembled prior to the table assembly shown here. Refer to
the assembly instructions included with the worksurface halves (Box #1) for assembly procedure.
(26) 035728
1/4-20 x 1/2” PHMS
(8) 0100167
8-32 x 1/2” PH
thread-cutting screw
(16) 059534
1/4-20 x 30mm JC bolt
(2) 0104836
4” snap-in grommet
(1) 021263
3-1/4” round grommet
(4) 037779
5/16-18 x 1” glide
(8) 041289
1/4-20 x 1-3/4” PHMS
(1) 025069
glide wrench
(1) 025039
4mm hex wrench
(2) 0112492
short side panel
(2) long side panel
0112491 - 84” tables
0112542 - 60” tables
(4) cord channel rail
0112495 - 84” tables
0112540 - 60” tables
(1) bottom panel
0112496 - 84” tables
0112541 - 60” tables
Cord Channel (Box #3)
Leg Assemblies (Box #2)
(1) 0112522
front leg assembly
(1) 0112535
rear leg assembly
(with grommet hole) (2) 059899
1/4-20 x 45mm JC bolt
(2) 021555
1/4-20 JC nut

0112776R4 Page 2 of 9
1. Attach legs to worksurface
A. Set the assembled worksurface face-down onto a at non-abrasive surface like a carpeted oor close to the table’s nal location.
B. Set the legs onto the bottom of the worksurface as shown with the insert panels facing toward the center. Figure 1. Note the rear leg
(with the grommet hole) will mount on the at edge of the worksurface.
C. Align the mounting holes and attach the legs with 1/4-20 x 1-3/4” PHM screws. Do not tighten these screws completely yet.
D. On the rear leg, install (2) 1/4-20 JC nuts, and (2) 1/4-20 x 45mm JC bolts through the worksurface. (This will require the worksurface
be lifted slightly off the oor and blocked up temporarily to install). It’s important these fasteners be installed for support before the unit is
tipped upright.
E. Install the glides onto the bottom of the legs and tighten securely.
Figure 1
assembled
worksurface
front leg
(no grommet)
rear leg
(with grommet hole)
1/4-20 x 1-3/4”
PHM screws
(4 on rear leg)
glide
(2 per leg)
1/4-20 x 1-3/4”
PHM screws
(6 on front leg)
1/4-20 x 45mm
JC bolts
(2 on rear leg)
1/4-20 JC nut
(2 on rear leg)

0112776R4 Page 3 of 9
Figure 2A
2. Attach cord channel rails to legs
A. Orient the upper cord channel rails with the inside rail anges pointing up
from the worksurface as shown. Figure 2A. Attach to the worksurface with
1/4-20 x 1/2” PHM screws.
B. Orient the lower cord channel rails with the inside rail anges pointing toward
the upper rail anges as shown and attach the end of each rail to each leg
with (2) 1/4-20 x 1/2” PHM screws. Figure 2B.
1/4-20 x 1/2” PHMS
(2) at each end
lower cord
channel rail
upper cord channel rails
attached to worksurface with
1/4-20 x 1/2” PHM screws
Figure 2B
rail anges on
inside pointing
toward each other
inside rail anges point
toward each other
1/4-20 x 1/2” PHMS
(2) at each end
Leg
Lower rail
Upper rails
rear leg
(with grommet hole)
front leg
(no grommet)
Lower rail

0112776R4 Page 4 of 9
3. Attach bottom panel
A. Attach the bottom panel to the two lower rails with (8) 8-32 x 1/2” PH thread-cutting screws as shown. Figure 3.
Note the end tabs will be pointing upward.
B. Attach each end tab on the bottom panel to each leg with (2) 1/4-20 x 1/2” PHM screws.
C. Tighten the leg screws from step 1C securely.
Figure 3
cord channel
bottom panel
8-32 x 1/2” PH thread-
cutting screws (8 req’d)
end tabs attached with
(2) 1/4-20 x 1/2” PHMS

0112776R4 Page 5 of 9
A. Lower the equipment rack over the cord channel as shown. Note the hinge-
side of each door will go toward the at edge (or rear) of the table. Figure 3A.
B. Open both equipment rack doors. Figure 3B.
C. Align the equipment rack and upper cord channel rail mounting holes.
D. Attach the equipment rack to each upper cord channel with (2) 1/4-20 x 1/2”
anged hex head screws and 1/4-20 keps nuts. Figure 3B.
E. Install (2) 1/4-20 x 1/2” anged hex head screws through the cord channel
bottom panel into each equipment rack side panel. Figure 3B.at edge / rear
of table
Figure 3A
open
doors
Figure 3B
(2) 1/4-20 x 1/2” anged
hex head screws
(4) 1/4-20
keps nuts
equipment rack
side panel
upper cord
channel rail
(4) 1/4-20 x 1/2” anged
hex head screws
(2) 1/4-20 x 1/2” anged
hex head screws
Note: The following procedure shows how to attach an optional equipment
rack to the table while the table is still upside-down during the table assembly.
cord channel bottom panel
upper cord
channel rail
upper cord
channel rail
equipment rack
Optional - Attach equipment rack to cord channel

0112776R4 Page 6 of 9
5. Install grommets
A. Install (2) 4” snap-in grommets into the bottom panel. Figure 5.
B. Install (1) 3-1/4” grommet into the rear leg panel.
6. Install side panels
A. Attach the short side panel to the cord channel rails toward the rear
leg with (4) 1/4-20 x 30mm JC bolts. Figure 6.
B. Attach the long side panel to the cord channel rails toward the front
leg with (4) 1/4-20 x 30mm JC bolts.
C. Repeat procedure on the other side of the table.
Figure 5
Figure 6
3-1/4” round
grommet
4” snap-in
grommet
4” snap-in
grommet
rear leg
(with grommet hole)
side panel
(long)
side panel
(short)
rear leg
(with grommet hole)
bottom
panel
1/4-20 x 30mm
JC bolts
cord
channel rail
4. Flip table upright
A. Using 4-5 people, carefully tip the table up on
its side and over until upright. Figure 4.
CAUTION
The table is heavy when assembled.
Use caution when ipping upright.
Figure 4
Note: If an equipment rack has been
installed and will be permanent, the
short side panels will not be needed.

0112776R4 Page 7 of 9
Worksurface cutouts
Note: Cutouts in the worksurface can be made by the
customer after the table has been assembled, but are only
recommended within the maximum cutout area shown
in Figures 7A & 7B. Cutouts made beyond this shaded
area could interfere with the legs, cord channel rails, or
worksurface reinforcement bars.
Note: When locating cutouts in the worksurface, consid-
eration should be given to avoid the draw bolts along the
worksurface seam. See draw bolt location dimensions.
maximum cutout area
maximum cutout area
draw bolt
draw bolt
Figure 7A
Figure 7B

0112776R4 Page 8 of 9
Options
Display Stand w/ Monitor Mount
mount supports 37”-63”
monitors up to 200 lbs
37106
Equipment Rack
7RU w/ 10” depth
41⁄2 RU w/ 25⁄8” depth
37107
Camera Mount
attaches to display stand
above or below monitor
(1 mount included)
37108
7-Outlet Power Strip, insured
w/ surge protector, bracket, and 12’ cord
99024
6-Outlet Power Strip
w/ 12’ cord
99023
WARNING
The monitor should always be lifted
off the stand before moving the table.

0112776R4 Page 9 of 9
925 First Avenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 1-800-235-1262 Fax: [phone]
E-mail: [email protected] web: www.spectrumfurniture.com
Warranty
WE WILL MAKE IT RIGHT FOR YOU!
Spectrum is committed to provide complete customer satisfaction. Each of our products are manufactured from the best materials available and each
product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations).
Our Customer Service Help Line 1-800-235-1262 is ready to provide immediate attention to any questions, comments or concerns. We are available
to answer your calls Monday through Friday from 7 am to 5 pm CST, excluding observed holidays. In addition your product comments or concerns are
welcome via e-mail at: [email protected].
Warranty Statement
We guarantee all Spectrum products to be free of all defects in materials and workmanship, for the original owner, for a period of ten years. Any item
deemed defective by Spectrum or the original manufacturer, under normal use conditions, will be repaired or replaced at Spectrum’s discretion. This
warranty applies to all products manufactured and distributed by Spectrum except the products
listed below.
Items that have a varying warranty include, but are not limited to, the following:
• Adjustable Crank/Electric Desk Legs (1 yr)
• Flat Panel Desk Gas Cylinders (1 yr)
• Upholstered Soft-Goods (5 yrs)
• Adjustable Height & Stacking Chair Parts – including frames, gas cylinders, wood and plastic parts, and control handles (7 yrs)
• Adjustable Height & Stacking Chair Casters (2 yrs)
• Chair Upholstery & Textiles (2 yrs of normal use of Soft Goods, Adjustable Height, Stacking, Wood and Metal Chairs)
• Chair Upholstery - Graded-In Fabrics and C.O.M (no warranty)
• Height Adjustable Columns and Lifts (1 yr)
• General Use Casters (1 yr)
• Electrical – Electri-Pak, Power Communication Modules, and special order ECA electrical items (1 yr)
• Electrical - Power Strips & Electrical Timers (1 yr)
• Electrical Surge Suppressors (lifetime)
• Electrical - Retractable Power Cords (1 yr)
• Keyboard/Mouse Trays (1 yr)
• Flat Panel Monitor Arm – General Parts (5 yrs)
• Flat Panel Monitor Arm – Gas Cylinders (2 yrs)
• CRT Monitor Arm (1 yr)
Warranty is void if product is not used for its intended purpose or subjected to an unusual application, multiple-shift use, alteration, accident, abuse or
abnormal wear and tear. Representations of colors on-line and in printed materials are meant to be a close reference to the actual colors but not an
exact match. Slight variations in color and texture of wood stains, powder coating, laminates, fabrics and other materials are normal in different manu-
facturing lots; as such these variations are not considered defects.
DESIGNED FOR INDOOR USE ONLY – Unless specifically stated in the product specifications, Spectrum’s products have been designed and con-
structed for indoor use only. Moving or using outdoors, or on excessively rough surfaces, may cause damage to the products and will void the warranty.
If an outdoor application is desired please contact us to discuss potential custom design solutions.
The warranty, as stated above, supersedes any previous warranties and is effective as of 9/1/2010