Spectrum Industries Esports Meta 37335 User manual

Assembly InstructionsAssembly Instructions
0192095 Page 1 of 4
Assembly InstructionsAssembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Esports Meta Desk - 37335Esports Meta Desk - 37335
Esports Shadow Desk - 37339Esports Shadow Desk - 37339
(1) Worksurface
(1) 021521
10-24 Keps nut
(9) 038064
#14 x 3/4” PHSM
(1) 025069
Glide Wrench
Hardware
3
/
8”
(4) 037779
5/16-18 x 1”
Glide
(6) 0100167
8-32 x 1/2” PH
Thrd ctg
(1) 0151223
Left Leg
(1) 0152137
Cord channel
bottom
(3) 035728
1/4-20 x 1/2”
PHMS
(3) 037542
#8 X 5/8” PHSM
0151838
Meta worksurface
0151201
Shadow
worksurface
(1) 0152138
Cord channel
front
(1) 0154472
Support panel
(1) 0151801
Worksurface
support beam
Note: Do not tighten fasteners completely until all have been installed.
Keeping them loose will help with alignment during assembly.
(1) 0151501
Right Leg
(1) 0150570
Headset
hanger
(1) 0152128
Mid bracket

0192095 Page 2 of 4
2. Attach laminate leg panels - optional2. Attach laminate leg panels - optional
1. If you ordered optional laminate leg insert panels, install them into
the legs at this point with (4) #14 x 3/4” PHSM screws. Figure 2.
If you don’t have laminate leg panels-skip to step 3.
1. Assemble worksurface1. Assemble worksurface
1. Place the worksurface laminate side-down onto a non-abrasive
surface like a carpeted oor. Figure 1.
2. Install the mid bracket as shown with (1) #14 x 3/4” PHSM screw.
Figure 1
(1) #14 x 3/4”
PHSM
Worksurface
Mid bracket
Figure 2
Laminate leg
panel insert
3. Attach legs to worksurface3. Attach legs to worksurface
1. Attach each leg to the worksurface with (2) #14 x 3/4” PHSM screws.
Do not tighten screws completely yet. Figure 3.
2. Install the (4) glides to the bottom of the legs. The glides can be
adjusted later to keep the desk level on uneven surfaces.
Figure 3
#14 x 3/4” PHSM
(2 per leg)
(4) Glides
Left Leg
Right Leg
#14 x 3/4”
PHSM
(2 per leg)
#14 x 3/4” PHSM
(4 required)

0192095 Page 3 of 4
4. Attach cord channel4. Attach cord channel
8-32 x 1/2” PH
Thrd ctg
(1 per leg)
Cord channel
bottom
Cord channel
front
(1) 10-24
Keps nut
Figure 4.1
Figure 4.2
Mid bracket
(3) 035728
1/4-20 x 1/2”
PHMS
1. Align the cord channel front with the leg holes and mid bracket as
shown. Figure 4.1. Secure with (2) 8-32 x 1/2” PH thread-cutting
screws and (1) 10-24 Keps nut at the mid bracket.
2. Align the cord channel bottom and secure to the cord channel front
with (3) 1/4-20 x 1/2” PHM screws. Figure 4.2.
3. Secure to each leg with (1) 8-32 x 1/2” PH thread-cutting screws.
8-32 x 1/2” PH
Thrd ctg
(1 per leg)

0192095 Page 4 of 4
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2020 Spectrum Industries Inc., All rights reserved.
Figure 7
5. Attach support panel5. Attach support panel
1. Align the support panel as shown. Figure 5.
2. Secure to the legs with (4) 8-32 x 1/2” PH thread-cutting screws.
3. Tighten ALL screws.
Figure 6
7. Attach headphone hanger7. Attach headphone hanger
1. The headphone hanger can be attached to the left or right-side of the
desk using (3) #8 x 5/8” PHSM screws. Figure 7.
8-32 x 1/2” PH
thrd ctg
(2 per leg)
8. Flip desk upright8. Flip desk upright
1. Using two people, carefully ip the assembled desk upright. Figure 8.
(3) #8 X 5/8”
PHSM
Support panel
Headphone
hanger
Figure 8
Worksurface
CAUTION
Do not allow the desk legs to contact the oor until
the table is completely ipped over. Excessive
side-loading of the legs could cause damage.
6. Attach metal leg panels - optional6. Attach metal leg panels - optional
Figure 5
Acrylic leg
panel assembly
8-32 x 1/2” PH
Thrd ctg
(4 per panel)
1. The upper rear screw is shared with the cord channel.
2. Attach the panel to the inside of each leg with (4) 8-32 x 1/2” PH
Thread cutting screws. Figure 1.
Leg