Spectrum 95506 User manual

043548R8 Page 1 of 2
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Micro Arm Keyboard Tray
95506
(1) 044480
Spacer block
1. Attach micro-arm bracket to keyboard tray
1. Align the micro-arm bracket with the 6 pre-drilled holes in the center of
the keyboard tray and attach with (6) #8 x 5/8” PHSM screws. Figure 1.
2. Tighten screws securely.
Figure 1
#8 x 5/8” PHSM
screws (6 required)
Phillips
screwdriver
Tools
Required
(5) 043878
Nylon spacer
1” x .375” OD
x .171” ID
(8) 026070
#8 x 1-3/4”
PHSM
(1) Slide guard
(1) 044321 Parts bag
(1) Rubber bumper
(8) #8 x 5/8” PHSM
Keyboard tray
Micro-arm bracket
Note: The spacers and longer screws are used between the slide and
worksurface only on worksurfaces with a 1” protruding support bar.
(1) 044217
Micro-arm
bracket
(1) 042342
17-3/4” Slide
(1) 043517
Keyboard tray

043548R8 Page 2 of 2
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
3. Attach slide guard
1. Flip the desk right-side up.
2. Slide the keyboard assembly into the slide. Figure 3A.
3. Using (2) #8 x 5/8” PHSM screws, attach the slide guard to the front
of the slide. Figure 3B.
Figure 3A
#8 x 5/8” PHSM
(2 required)
Slide guard
2. Attach slide to desk
1. Flip the worksurface / desk upside-down onto a non-abrasive surface.
2. Locate the slide perpendicular and about 1” from the edge of the
worksurface. The slide should not be mounted closer than 8” to the
nearest leg.
Note: The nylon spacers and longer screws are used between the slide
and worksurface only on worksurfaces with a protruding support bar.
Figure 2A
Attach 1”
from edge
Slide
Spacer
block
Underside of
worksurface
#8 x 1-3/4” PHSM
Nylon
spacer
Support bar
Figure 2B
Figure 3B
Keyboard
assembly
Rubber
Bumper
Slide under
worksurface
Installation on desks with support barTypical installation
3. Attach the slide using (8) #8 x 5/8” PHSM screws and tighten securely.
Figure 2A.
4. Attach the rubber bumper toward the back of the slide using the
middle hole.
#8 x 5/8” PHSM
Slide
Attach 1”
from edge Underside of
worksurface
3. Place the spacer block and (5) nylon spacers under the tray as
shown Figure 2B.
4. Attach the slide, spacer block, and nylon spacers using (6) #8 x
1-3/4” PHSM screws and tighten securely.
5. Attach the rubber bumper toward the back of the slide using the middle hole.
Rubber
bumper