Steelcase 4200 Woodcore Firmware update

Steelcase, Inc.
Grand Rapids, MI 49501
U.S.A.
1-888-783-3522
Tools
Assembly Directions REV
93-9500819 A
Page 1 of 4
Mounting 3200 And 4200 Woodcore or Steel Auxiliary Tops Onto
800 Series Lateral Files Or Bullnose Woodcore Auxiliary Top Onto
800 Or 900 Series Lateral Files
NOTE: The following directions illustrate a 3200 or 4200 wood or steel top assembled onto 800 series lateral files and is
typical for “Bullnose Auxiliary Top” installation except screw size noted in Step 3.
1/4” DRILL BIT
2
3
4
7/32” SOCKET

Assembly Directions
93-9500819 REV A
Page
2 of 4
1.
NOTE; Prior to installation of Auxiliary Top, remove the top drawer(s) or door(s). If Auxiliary Top is to be installed onto a
single file, Step 1 and proceed onto Step 2 of these directions.
Attaching files together
Locate and remove (2) knock-out slugs at the top of each
mating side of file. CAUTION: Do not remove knock-out
slugs from any side other than mating sides.
1b. Align files in exact floor location. Glides may be
adjusted for uneven floors.
1c. Bolt files together at top using No. 10-24 x 1/2”
screws and No. 10-24 wing nuts.
1d. To gang files together at the bottom (when necessary)
drill 1/4” dia. holes thru case sides approximately 4” up
from the bottom of file and 4” in from the front and back
file. Bolt together in the same manner as the top.
KNOCK-OUT
HOLES
BOTTOM OF
FILE
GLIDE ADJUSTMENT
1/4” DIA. HOLES

Assembly Directions
93-9500819 REV A
Page
3 of 4
2. Marking hole locations on top(s) of files(s)
Starting from the left side and front edge(s) measure and mark places to be drilled. Use hammer and center punch
to locate holes. Drill 1/4” hole at required locations.
3. Positioning and securing top onto lateral files(s)
Center top onto file(s). Align slots in top braces of 4200 Series with drilled holes in top of lateral file(s) Secure top
in place starting at the two extreme front corners. NOTE: A 9/64” dia. x 1/2” deep pilot holes can be drilled into the
top, using the holes in the lateral file(s) top as a guide. Use No. 10 x 3/4” screws to secure all tops except “Bullnose
Tops” which require No. 10 x1” screws. The illustration below illustrates (2) side views of bullnose top positioned on
top of file(s). One top allows the overhang only at the front of file(s), while the other allows the overhang at both
front and rear of files(s).
Bullnose top with round
edge at front only
Bullnose top with round
edge at front and rear sides
ALIGN TOP
FLUSH
WITH EDGE
OF FILE(S) ALIGN TOP FOR A
1/2” OVERHANG AT
THE FRONT AND REAR
OF FILE(S)
1/4” HOLE

Assembly Directions
93-9500819 REV A
Page
4 of 4
Chart “A”
C
34 3/32”
44 3/32”
46 3/32”
56 3/32”
58 3/32”
OVERALL TOP SIZE NO. OF 1/4” DIA.
HOLES REQ’D
30 1/8” x 18” 4
36 1/8” x 18” 4
42 1/8” x 18” 4
60 3/16” x 18” 8
66 3/16” x 18” 6
72 3/16” x 18” 8
78 3/16” x 18” 6
84 3/16” x 18” 8
8”61/309
96 3/16” x 18” 8
B
26 3/32”
33”
28 3/32”
39”
38 3/32”
34 3/32”
38 3/32”
D
26 1/16”
32 1/16”
38 1/16”
56”
62”
68”
74”
80”
86”
92”
A
4 1/16”
4 1/16”
4 1/16”
4 3/16”
4 3/16”
4 3/16”
4 3/16”
4 3/16”
4 3/16”
4 3/16”
FRONT EDGE OF FILE(S)
1/4” DIA. HOLES, SEE CHART
FOR NO. REQ’D
4”
10”
A
B
C
D
OVERALL TOP SIZE
BOOKCASE
SHIPPING CLIP
Shipping clip to be removed
at assembly and discarded.
Shipping clip is used on:
*2200 and 720 Bookcases
*800 Lateral Hang-ons
*752 OverFile Storage.
SHELF SUPPORT CLIP
Shelf support clip (used under shelf)
not to be discarded or confused with
above shipping clip.