Steelcase UPV Series User manual

UPV Series Storage
Assembly Instruction
August 2014 Page 1 of 18
Required Tools
1. Power Driver
2. Plus Bit
3. Minus Bit
4. Plus Screwdriver
5. Minus Screwdriver
Disassembly can be achieved by using the assembly instructions as a guide, further break down of the main
structure is not required as it is composed of one material type.

August 2014 Page 2 of 18
UPV Series Storage
Assembly Instruction
All cabinet are without pre-cut holes except for Single Hinge Door
1. For up-down ganging, installer can refer to guide holes from
inside to dril out
For ganging
side cabinets
Internal Guide Holes

August 2014 Page 3 of 18
UPV Series Storage
Assembly Instruction - Ganging Cabinets
1
2
3
Ganging Cabinets
1. Ganging upper to lower cabinets.
2. Ganging side cabinets.
3. Ganging back cabinets.
M6
M6
M6*10
M6*10
M6*10

August 2014 Page 4 of 18
UPV Series Storage
Assembly Instruction
M5*12

August 2014 Page 5 of 18
UPV Series Storage
Assembly Instruction - Removable Runner
1 2
Removable Runner
1. Install the runner at the cabinet.
2. Insert drawer into runner sequentially

August 2014 Page 6 of 18
UPV Series Storage
Assembly Instruction - Counter Weight
Counter Weight Info:
1. 2H = 7 pcs = 42 kg
2. 3H = 6 pcs = 36 kg
3. 4H = 5 pcs = 30 kg
Counter Weight (for drawer cabinet only)
1. Take out the drawer one by one.
2. Slot in the counter weight.
3. Put back in the drawer one by one.
1
3
2
Drawer cabinet body

August 2014 Page 7 of 18
UPV Series Storage
Assembly Instruction - File Hanger
1
2
File Hanger
1. Vertical Hanging Rail
2. Horizontal Hanging Rail

August 2014 Page 8 of 18
UPV Series Storage
Assembly Instruction - Drawer
1
Drawer
1. Fix the drawer divider by slotting into
the parallel holes.

August 2014 Page 9 of 18
UPV Series Storage
Assembly Instruction - Adjustment Knob
Adjustment Knob
1. Adjust glide for leveling.

August 2014 Page 10 of 18
UPV Series Storage
Assembly Instruction
Adjustable Shelf
1. Insert all four brackets in position as shown.
2. Place shelf on top of the brackets.
1
2

August 2014 Page 11 of 18
UPV Series Storage
Assembly Instruction - Tambour Door Storage
1
2
34
NOTE: Plastic hook are not necessarily for shelf fitting

August 2014 Page 12 of 18
UPV Series Storage
Assembly Instruction - Open and Sliding Door Storage
NOTE: Plastic hook are not necessarily for shelf fitting

August 2014 Page 13 of 18
UPV Series Storage
Assembly Instruction - Single Hinge Door
Side Bracket
1. Screwed the bracket to the side panel.
2. Knock out the pre-cut holes with mallet
(either left or right side).
2
1

August 2014 Page 14 of 18
UPV Series Storage
Assembly Instruction - Floor and Wall Mount
Floor and Wall Mount
1. The longer part must attach to cabinet body because the
cabinet bottom structure will block the screw.
2. Advisable the longer bracket hook with cabinet and short
bracket side mount with wall.
Wall
2
1
NOTE: All cabinets 1810mm H or higher should be bolted
to a wall with the wall attachment brackets.

August 2014 Page 15 of 18
UPV Series Storage
Assembly Instruction
Cushion Top
1. Drill holes from top with attached template guide.
2. Unload the drawer.
3. Tight the cushion top with screws
4. Put back the drawers one by one.
1
3
3
1

August 2014 Page 16 of 18
UPV Series Storage
User Guide- Door Adjustment
Door Adjustment
1. Adjust screw to move the door to left or right (movement ‘a’)
2. Adjust screw to move the door forward or backward (movement ‘b’)
3. Adjust screw to move the door up or down (movement ‘c’)
2
1
3

August 2014 Page 17 of 18
UPV Series Storage
User Guide - Loading and Unloading Files
Loading and Unloading Files
Note:
1. Always load the drawers from bottom upward.
2. Always unloading the drawers from top downward.
LOAD UNLOAD

August 2014 Page 18 of 18
UPV Series Storage
User Guide - Cautions
CAUTION
1Mobile Pedestal & Caddy
Pedestal must install with counter
weight to prevent tip off.
4Load lower
openings with
heavier material
first. Distribute
weight within
each opening
evenly. Do not
move cabinet or
adjust glides with loaded roll-outs.
Do not lift unit by its tops.
2Gang cabinets together
side-to-side, back-to-back or
top-to-bottom can refer to top
plate guide holes.
5The interlock system prevents
more than one roll-out from opening
at a time. Do not try
to force open
more than one
roll-out at
a time.
3If lateral cannot be ganged
or mounted under
a worksurface,
a counterweight
package must
be installed.
6When loading with materials,
refer to maximum loading capacity
on each shelf or drawer types to
prevent any accident or damage of
product.
FOLLOW THESE INSTRUCTIONS TO PREVENT CABINET FROM TIPPING OVER
AND CAUSING PERSONAL INJURY. THESE INSTRUCTIONS APPLY TO ALL FILES.
DO NOT REMOVE THIS LABEL.
Lateral 40kg Pen Drawer 2kg
Single Hinge Door 20kg Box Drawer 7kg
Hinge Door 36kg File Drawer 15kg
Sliding Door 36kg Caddy Shelf Loading 12kg
Tambour Door 36kg Cushion Top
Max loading 85kg
Open Door 36kg