Steelcase DOUBLE PEDESTAL DESK Firmware update

Steelcase, Inc.
GrandRapids, MI 49501
U.S.A.
1-888-783-3522
Y9501946
Rev. G
Assembly Directions
Tools
Printed in the U.S.A.
1/8"
(3.1 mm)
IMPACT - Attaching Pedestal, End Panel
and Center Kneespace Panel to Worksurface
DOUBLE PEDESTAL DESK
(showing slip fit)
LH SINGLE PEDESTAL DESK
(shown in this direction)
FULL STORAGE CREDENZA
LH KNEESPACE CREDENZA
w/ CENTER SUPPORT PANEL

1.
2.
3.
5.
4.
Page 2 of 6
Y9501946 Rev. G Steelcase
Carefully flip worksurface over onto carpet or other soft material.
Determine (side to side) location of pedestal under worksurface.
Position brackets (2 per pedestal) so that openings and holes in
flanges are aligned with routs in worksurface. This will help keep
assembly square.
Note: For worksurfaces without routs, draw lines at dimensions
shown to align bracket holes.
Secure each bracket with (6 or 8) screws provided, depending
on length of bracket.
Note: mid-point of pedestal will be the same as midpoint of rail
(this will allow for maximum slip fit movement).
ATTACH A PEDESTAL TOAWORKSURFACE
Note: this page shows how to installapedestal flush with the worksurface forasingle ped desk.
You may want to position the pedestal so it extends beyond the worksurface (slip fit) and with a
credenza you may have multiple pedestals. Location of pedestals always determines where
to install the rails.
When all brackets are attached proceed to page 6.
WORKSURFACE FRONT
2”
(51 mm)
minimum
Install screws into routs
14” Rail shown, also available
are 8”, 26”, and 32” depending
on pedestal width.
(6) or (8) Screws
per bracket, 10-12
x 5/8” pan head
66.5
mm
173
mm
173
mm
429
mm

2.
3.
1. Fit in the routed recess of end panel
and attach with .250-14 x 1.00” screws.
worksurface before attaching to back panel.
Attach back panel to end panel.
Install (3) steel dowels into holes in
back panel.
Insert (3) cam locks into openings in
end panel.
Position the panels together and
secure with a half turn of cam locks.
(2) L-brackets
Z-bracket is to be attached toNOTE:
A
B
C
Using end panel assembly as
reference, locate the pilot holes
ATTACH AN END PANEL TO A WORKSURFACE
L-bracket Z-bracket
Page 3 of 6
Y9501946 Rev. G Steelcase
(2) Screws per bracket
.250-14 x 1.00” pan head
A
C
CAM LOCK (arrow will
always point toward dowel)
B
1
2
BACK PANEL
END PANEL
2
Worksurface
Top
Z Bracket
3
3
10-16
x 3/4”
on bottom of worksurface that
matches routed area on end
panel for Z-bracket.
Attach (2) Z-brackets to
bottom of worksurface with
two 10-16- x 3/4" screws each.

4.
5.
Lower assembled end panel into place
(rear and side edges will be flush with
worksurface and rear edge will be inset 6"
for desk worksurface).
Secure all brackets with screws provided.
WORKSURFACE REAR
Page 4 of 6
Y9501946 Rev. G Steelcase
6. When assembly is complete proceed
to page 6.
(2) Screws
per bracket
10-16 x .3/4”
pan head
TOP VIEW
Outside
and
rear edges must
be flush with
credenza
worksurface and
rear edge will be
inset 6" for desk
worksurface.
NOTE
If hutch option is being installed,
drill through pre-drilled pilot holes
before installing end panels.
END PANEL
BACK PANEL
(4) Screws
.250-14 x 1.00”
credenza

WORKSURFACE REAR
TOP OF PANEL
ATTACH A CENTER SUPPORT TOAWORKSURFACE
A center support panel is required only when there
isakneespace span of greater than 54”.
Attach an angle bracket to each side
of top of support panel as shown.
1.
Lower assembly onto worksurface
and position so that it is centered in
kneespace span and flush with the rear
edge of worksurface.
Secure with screws provided.
When all components are attached proceed to page 6.
Page 5 of 6
Y9501946 Rev. G Steelcase
2.
3.
4.
(5) 10-16 x 3/4”
pan head screws
each bracket
(5) 10-16 x 3/4”
pan head screws
each bracket

Page 6 of 6
Y9501946 Rev. G Steelcase
TO COMPLETE ASSEMBLY
Remove back panel and
top drawer(s) for access
to pedestal interior.
Put pedestal(s) approximately
in final location.
Carefully lower worksurface
assembly onto pedestal(s),
engaging protruding brackets
through openings in rails.
Secure pedestal(s) to
worksurface as shown.
Reinstall drawer(s) and
back panels.
1.
2.
3.
4.
5.
Metal brackets
will fit into openings
in rails.
Secure each bolt with
a rectangular nut.
(2) bolts per rail
.250-20 x 1-1/4”
pan head
You may need to remove
(1) screw per side to remove
drawer, then reinstall when
assembly is completed.