Steelcase FrameOne User manual

FrameOne™Bench - Continuous Top
Page 1 of 16
25184001 Rev B
(5mm)
HEX DRIVE
#2 SQUARE
DRIVE
Continuous Top with End Counter
Continuous Top Bench 17mm Socket
1/8" Dia.
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2015 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Table of Contents
Topic Page
Frame Assembly
Power Access Door Package
2
4
Rubber Mallet
Worksurface Assembly 3
Power Block Installation 5
Assembly for New York Power-In Feed
Hardwire Version
Power Cover
End Counter Installation
6
8
9
10
Worksurface Installation
Tray Installation
Worksurface Adjustment
11
12
13
Continuous Top Base and Extension 14

Frame Assembly
Page 2 of 16
25184001 Rev B
®
4X
2
FRONT OF FRAMES
EIGHT (8) LARGE SCREWS
FRAME
END LEG
1
2
2
2
2

2a
Page 3 of 16
25184001 Rev B
®
CANTILEVER
Worksurface Assembly
BOTTOM OF WORKSURFACE
1. Turn the worksurface over onto a
clean, soft surface.
2. Locate and install (2) cantilevers
using spacer blocks as shown.
1
2c
2b
3

Power Access Door Package
(12) 1/2"
SCREWS
Page 4 of 16
25184001 Rev B
®
NOTE: Install screws by hand only.
Using a power driver could cause
damage to the product!
1. Install (2) access door assemblies into openings
as shown.
NOTE: Install screws by hand only. Using a
power driver could cause damage to the product!
1

Power Block Installation
Page 5 of 16
25184001 Rev B
®
1. Install power block bracket to worksurface
with (4) #10-12 x .625" screws.
2. Attach power block as shown.
1
2
NOTE: Power block must be mounted
in the center slots.
Modular Power
Standard Capacity = 1 block
RECEPTACLE
COVER
NOTE: If receptacles are not required inside a power block,
make sure to apply a receptacle cover to ALL open ports.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interface when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USB RECEPTACLE
OR
NOTE: For hardwire versions, go to page 8.
POWER BLOCK
BRACKET
POWER
BLOCK
NOTE: The electrician can cut conduit
and wire to length if needed.

Page 6 of 16
25184001 Rev B
®
Assembly for New York Power-In Feed
1.Assemble junction box, without cover.
NOTE: Determine which end of the desk
frame the box will be mounted. Electrician to
remove knockouts prior to mounting junction
box.
The modular/hardwire harness provided is
supplied for a maximum length desk and will
need to be cut to length for shorter desks.
desired.
2. Measure length from the junction box to the
modular connector (plan junction box distance
mounted 6" from cantilever. See page 5).
Remove conduit connector before cutting modular/
hardwire harness to length (2a). Reattach conduit
connector, tighten nut, and secure to junction box.
Route modular/hardwire harness through knockout
with electrician's power supply cable. Electrician to
connect power source wires to the modular/hardwire
harness with wire nuts (2b). Place connected power
inside junction box and fasten junction box cover (2c).
NOTE: If nuts cannot be tightened, remove item 1A,
tighten and reattach.
Harness route and trim may be completed after
mounting junction box if desired.
1
1A
2a
2b
2c
WIRE NUT
JUNCTION BOX
COVER
ELECTRICIAN
SUPPLIED
CONDUIT
CONNECTOR

Page 7 of 16
25184001 Rev B
®
Assembly for New York Power-In Feed (continued)
3.Locate junction box 6" inward from the cantilever bracket on the underside
of the frame. Align box and pre-drill holes for #10 screws, (#22 drill bit).
4. Attach the box with screws provided.
5. Drill pilot holes for strain relief brackets. Attach the harness strain relief
bracket to the bottom side of the horizontal rail with screw provided (5a).
Insert harness into the bracket (5b) and secure harness with nut and bolt
(5c). Connect the modular end of the harness to the first modular power block.
Attach electrician supplied harness strain relief bracket in location shown.
Follow steps 5a - 5c to secure electrician's harness.
4
3
CANTILEVER
6"
5b
5c
5a
STRAIN RELIEF
BRACKET

Page 8 of 16
25184001 Rev B
®
6a
Hardwire Version:
One hardwire box installs
centered on the bracket.
BEND DOWN
Alternate Assembly for Hardwire
NOTE: For proper fit of
receptacle, remove all
ears on receptacle
Chicago
Hardwire
6b
6c
NOTE: Steps 6c through 6e are also
required on all Power-In feeds.
6d
6e
Secure to
WORKSURFACE

Page 9 of 16
25184001 Rev B
®
7.Install power covers.
POWER COVER
7h
7a 7b
7f 7g
7c
7d
7e

Page 10 of 16
25184001 Rev B
®
2b
2a
4X
2c
4X
2d
4X
Install set screw
to level unit.
2e
4X
NOTE: Longer flange is
located towards the top.
NOTE: Align edge
of worksurface to
the side of leg.`
NOTE: Bend/Adjust lower flange as necessary
to ensure a proper fit up of cover.
1
End Counter Installation
(If ordered)