Steelcase DATUM-C2 User manual

Page 1 of 17
DATUM-C2 STORAGE
Assembly Instruction
®
September 2011
1. Power Driver
7. Allen Key
8. 2 persons are needed
2. Plus Bit
3. Minus Bit
4. Plus Screwdriver
5. Minus Screwdriver
6. Mallet
Required Tools

Page 2 of 17
®
Knockouts (for ganging)
1. Knockout pre-cut hole using a mallet
and a pen-tip chisel.
Note: All knockout for ganging is
from outside to inside
1
DATUM-C2 STORAGE
Assembly Instruction
For wood top
attachment
For ganging
side cabinets
For ganging upper or
lower cabinets
For wood top
attachment
September 2011

Page 3 of 17
®
Ganging Cabinets
1. Ganging upper to lower cabinets.
2. Ganging side cabinets.
3. Ganging back cabinets.
2
1
3
DATUM-C2 STORAGE
Assembly Instruction - Ganging Cabinets
M6*8
M6
M6*8
M6*8
M6
September 2011

Page 4 of 17
®
Base
1. Fix M6*35 screws from the body case to
the base unit.
1
DATUM-C2 STORAGE
Assembly Instruction - Base
M6*35
Base
Case Body
基地
箱体
September 2011

Page 5 of 17
®
Wood Top
1. Fix M5*12 screws from the body case to
the wood top from inside the cabinets
using Ganging Kit.
1
DATUM-C2 STORAGE
Assembly Instruction - Wood Top
M5*12
September 2011

Page 6 of 17
®
Removable Runner
1. Install the runner at the cabinet.
2. Insert drawer into runner sequentially.
1
2
DATUM-C2 STORAGE
Assembly Instruction - Removable Runner
September 2011
快折式滑轨
快折式滑

Page 7 of 17
®
Counter Weight (for drawer cabinet only)
1. Take out the drawer one by one.
2. Slot in the counter weight.
3. Put back in the drawer one by one.
12
3
DATUM-C2 STORAGE
Assembly Instruction - Counter Weight
Drawer cabinet body
Counter Weight Info:
1. 2H = 7 pcs = 42 kg
2. 3H = 6 pcs = 36 kg
September 2011

Page 8 of 17
®
Adjustment Knob
1. Without base adjustment.
2. With base adjustment.
12
DATUM-C2 STORAGE
User Guide - Adjustment Knob
September 2011

Page 9 of 17
®
Leveling Adjustment
a. With Base
(use Allen Key)
b. Without Base
(use Allen Key)
DATUM-C2 STORAGE
User Guide - Leveling Adjustment
Case Body
M6*35
Base
September 2011

Page 10 of 17
®
DATUM-C2 STORAGE
Base Installation Guide
Tambour Door B
B
A
A
A
B
C
C
C
C
C
Lateral File
Hinged Door
Sliding Door
Front Back
Front
Back
September 2011
移门柜
开门柜
理想柜
卷门柜

Page 11 of 17
®
File Hanger
1
2
DATUM-C2 STORAGE
Assembly Instruction - File Hanger
1. Vertical Hanging Rail.
2. Horizontal Hanging Rail.
September 2011

Page 12 of 17
®
Drawer & Shelf Folder Divider
1
2
DATUM-C2 STORAGE
Assembly Instruction - Drawer & Shelf Folder Divider
1. Fix the Drawer Divider by slotting it into
the parallel holes.
2. Install the Shelf Folder Divider by
a) Press inward
b) Place it into the slot
b
a
a
September 2011

Page 13 of 17
®
Adjustable Shelf
12
2
DATUM-C2 STORAGE
Assembly Instruction - Adjustable Shelf
1. Insert all four brackets in position as shown.
2. Place shelf on top of the brackets.
Shelf
September 2011

Page 14 of 17
®
Door Adjustments
1
2a
b
c
3
DATUM-C2 STORAGE
User Guide - Door Adjustments
1. Adjust screw to move the door to left or right (movement ‘a’)
2. Adjust screw to move the door forward or backward (movement ‘b’)
3. Adjust screw to move the door up or down (movement ‘c’)
September 2011

Page 15 of 17
®
Loading and Unloading Files
DATUM-C2 STORAGE
User Guide - Loading and Unloading Files
Note:
1. Always load the drawers from bottom upward.
2. Always unloading the drawers from top downward.
DAOLNUDAOL
September 2011

Page 16 of 17
®
Parts Table
DATUM-C2 STORAGE
User Guide - Parts Table
Glide
DC94571S
Hinged Door 601
601
601
4
4
4
4
4
4
4
4
4
4
4
48
4
6
DC94571L
Lateral Drawer
DC945103L
Sliding Door
DC945174H
Tambour Door
DC94506B
M4*10 M5*12 M6*8 M6*30 M4*10 M6 Base Glide
September 2011

Page 17 of 17
®
DATUM-C2 STORAGE
User Guide - Cautions
FOLLOW THESE INSTRUCTIONS TO PREVENT CABINET FROM TIPPING OVER
AND CAUSING PERSONAL INJURY. THESE INSTRUCTIONS APPLY TO ALL FILES.
CAUTION
6
When loading with materials,
refer to maximum loading capacity
on each shelf or drawer types to
prevent any accident or damage of
product.
Type
Lateral
Sliding door
Tambour door
Hinged door
60 KG
45 KG
40 KG
45 KG
Gang cabinets together
side-to-side, back-to-back or
top-to-bottom thru knockout
holes using
hardware
included.
Wall ganging
hardware is
not included.
2
1
Level the
cabinet using glides.
5
The interlock system prevents
more than one roll-out from opening
at a time. Do not
try to force open
more than one
roll-out at a
time.
4
Load lower
openings with
heavier material
first. Distribute
weight within
each opening
evenly. Do not
move cabinet or
adjust glides with loaded roll-outs.
Do not lift unit by its top.
If lateral cannot be ganged
or mounted under
a worksurface,
a counterweight
package must
be installed.
3
September 2011