Steelcase Hang-On Acoustical Panel User manual

Steelcase, Inc.
Grand Rapids, MI 49501
U.S.A.
1-888-783-3522
Tools
Assembly Directions Printed In U.S.A.
REV
93-9501116 A
Page 1 of 4
MIGHTY HAMMER
Hang-On Acoustical Panel Installation
CASEGOOD HARDWARE
PACKAGE CONTENTS
QTY. NAME
1 ACOUSTICAL PANEL
4 SUPPORT CLIPS
4 No. 6 TEK SCREWS
7/64” DRILL BIT

Assembly Directions
93-9501116 REV A Page 2 of 4
1.
Acoustical Panels Installed On Backs Of Series 9000®Units
Refer to chart and below figure for center punch
locations. Punch required locations for your size
acoustical panel. Drill 7/64” Dia. pilot holes.
2. Position and secure (2) top brackets
with (1) screw.
3. Position and secure (2) bottom brackets
with (1) screw.
4. Place acoustical frame return flange onto (2) top
brackets. Push bottom of acoustical panel in
until the bottom brackets snap into place.
NOTE: To remove the acoustical panels, lift up
and tilt from side to side.
SCREW
NO. 6 TEK
BOTTOM
BRACKET
TOP
BRACKET
ACOUSTICAL FRAME
RETURN FLANGE
UNIT SIZE PANELS REQ’D DIM. “A” DIM. “B” DIM. “C”
65” x 75” 2 6-1/2” 27-7/8” 10”
65” x 70” 2 6-1/2” 25-3/8” 10”
65” x 65” 2 6-1/2” 22-7/8” 10”
65” x 60” 2 6-1/2” 20-3/8” 10”
65” x 45” 1 6-1/2” --- 10”
MOUNTING CLIP HOLE LOCATIONS
5/8”
10”
A
B
C
TOP
BRACKET
SCREW
NO. 6 TEK

1.
Acoustical Panels Installed On The Side Of
Series 9000®End Panels And Spanner Panels
Center punch (4) locations onto end panel or spanner
panel (R.H. shown typical) Drill 7/64” Dia. pilot holes. 2.
Position and secure (2) top brackets with (1) screw.
3. Position and secure (2) bottom brackets with (1) screw. 4. Place acoustical frame return flange onto (2) top
brackets. Push bottom of acoustical panel in until
the bottom brackets snap into place. NOTE: to
remove the acoustical panels, lift up and tilt from
side to side.
5-1/2”
5/8”
10”
3/4”
5/8”
5-1/2”
TOP
BRACKET
TOP
BRACKET
SCREW
NO. 6 TEK
SCREW
NO. 6 TEK
BOTTOM
BRACKET
TOP
BRACKET
ACOUSTICAL
FRAME RETURN
FLANGE
Assembly Directions
93-9501116 REV A Page 3 of 4

1.
Acoustical Panels Installed To
Back And Side Of Lateral Files
Center punch locations. Drill 7/64” Dia. pilot holes. 2.
Position and secure (2) top brackets with (1) screw.
3. Position and secure (2) bottom brackets with (1) screw. 4. Place acoustical frame return flange onto (2) top
brackets. Push bottom of acoustical panel in until
the bottom brackets snap into place. NOTE: to
remove the acoustical panels, lift up and tilt from
side to side.
5-1/2”
5/8”
3/4”
10”
SCREW
NO. 6 TEK
TOP BRACKETS
SCREW
NO. 6 TEK
5/8”
SCREW
NO. 6 TEK
BOTTOM
BRACKET
ACOUSTICAL
FRAME RETURN
FLANGE
Assembly Directions
93-9501116 REV A Page 4 of 4
5-1/2”