Steelcase Elective Elements Paper Organizer User manual

Page 1 of 7
939500614 Rev B
Elective Elements - Paper Organizer
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
© 2006 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
DRILL BIT
5/32"
Paper Organizers supporting
an open overhead cabinet
installed on a desk
(shown in this direction).
Paper Organizer and
single hutch support.

Page 2 of 7
939500614 Rev B
1. Insert (female) pieces of the quick dowels
into holes in the back panel of organizer
(6 each side).
Note: taller units will use more quick dowels.
2. Install (male) pieces of the quick dowels into
holes in an end panel of organizer (6 each panel).
3. Repeat the procedure for the other end panel. BACK PANEL
QUICK DOWEL
(FEMALE)
QUICK DOWEL
(MALE)
END PANEL
1
23
ASSEMBLE ORGANIZERS

Page 3 of 7
939500614 Rev B
4. Press the end panels onto the back
panel so that the quick dowel components
are securely engaged.
5. Cut and install felt padding on bottom
and top surfaces of assembled panels.
6. Insert shelf support pins into holes in
end panels.
7. Lower adjustable shelves onto pins.
7
6
4
4
FELT PADDING
5

Page 4 of 7
939500614 Rev B
INSTALL ORGANIZERS ONTO WORKSURFACE
1
2a 2b
MODEEZ SCREW
1. Determine locations for modeez screws.
2. Drill (8) pilot holes 1/2" (12.7mm) deep
(2a). Install (8) modeez screws (2b).
REAR
WORKSURFACE TOP
DRILL BIT
(5/32")
Drill (4) pilot holes per end,
5/32" (3mm) dia. x1/2" (13 mm) deep
3/8"
(10 mm)
14-9/16"
(370 mm)
2-1/16"
(52 mm)
12-7/16"
(316 mm)

Page 5 of 7
939500614 Rev B
3. Position organizers above the
worksurface so that modeez screws are
located to the front of female fasteners.
4. Slide organizers in direction of arrow
until modeez fasteners are securely
engaged over screws. MODEEZ
SCREW
FEMALE
FASTENER
3
4a
4b

Page 6 of 7
939500614 Rev B
1. Refer to the drawing to locate modeez screws
on the bottom surface of the overhead cabinet.
2. Drill (8) pilot holes 1/2" (12.7mm) deep (2a).
Install (8) modeez screws (2b).
INSTALL OVERHEAD CABINET
REAR
CABINET BOTTOM
Drill (4) pilot holes per end,
5/32" (3mm) dia. x1/2" (13 mm) deep
3/8"
(10 mm)
14-9/16"
(370 mm)
2-1/16"
(52 mm)
12-7/16"
(316 mm)
1
BOTTOM VIEW OF
CABINET BOTTOM
MODEEZ SCREW
DRILL BIT
(5/32")
2a 2b

Page 7 of 7
939500614 Rev B
3. Position overhead cabinet above the
organizers so that modeez screws are
located to the front of female fasteners.
4. Slide organizers in direction of arrow
until modeez fasteners are securely
engaged over screws.
MODEEZ
SCREW
FEMALE
FASTENER
3
4a
4b