Steelcase Currency Workwall User manual

Page 1 of 12
939500279 Rev E
Currency®- Workwall
#2
CAM LOCK
ADJUSTMENT TOOL
1/8"
(3.1 mm)
Drill Bit
3"
(76.2 mm)
Drill Bit
3 Unit 4 Unit 5 Unit
NOTE:
Workwall can be used as a divider with
doors on either side of the unit.
NOTE:
Two people are recommended for the assembly of Workwall.
Make sure to assemble Workwall on a clean, padded surface
to avoid any scratches or damage to any of the parts.
TOOLS FOR INSTALLING A 3" GROMMET ONLY
NOTE:
Make sure the assembly has been completed
before removing all of the E, B, I, MC, ect.
stickers from the surfaces of all the parts.
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE(888.783.3522)
for immediate action bypeople who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2012 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®

Page 2 of 12
939500279 Rev E
Components
Letter Description
E End Panel
B Back Panel
I Inner Panel
T Top Shelf
MC Middle Shelf, Closed
LC Lower Shelf, Closed
MO Middle Shelf, Open
LO Lower Shelf, Open
A Adjustable Shelf
E
TTT
A
A
A
A
A
A
A
A
A
MC
LC
B
I
I
MO
LO
B
MC
LC
E
®

Page 3 of 12
939500279 Rev E
(Tips for Proper Alignment of Parts)
CAM LOCK
CAM PIN
CAM LOCK
(See cam lock note)
CAM LOCK
CAM LOCK ADJUSTMENT TOOL
Apply stickers on all visible cam
joint faces to cover the connector
faces, after assembly.
Make sure the cam
lock is located parallel
to the side of the
surface as shown.
CAM LOCK NOTE:
If cam lock is installed high on the surface,
tap it down flush with the surface. If that
doesn't work, replace part.
If cam lock is installed low into the surface,
screw cam pin out to extend the length of
the cam pin.
NOTE: The cam pin is offset and needs
to be installed on the shorter offset side.
If the screw heads are not visible, turn
the panel/shelf 180o.
PANEL
Shorter off-set side
NOTE: When assembly has been completed,
make sure to remove all of the E, B, I, ect.
stickers from the surfaces of all the parts.
Fasten Cam Locks
(The cam lock screw needs to
be turned 3/4 full turn or 270o
clockwise for complete
engagement.)
If the cam lock screw is not
visible, you have installed
the panel/shelf wrong and
you need to turn the
panel/shelf 180o.
WRONG
TURN
CLOCKWISE
Use mallet, before tightening cam screws, to
bring parts together and avoid light leaks.
®

Page 4 of 12
939500279 Rev E
3 Opening Unit
2
NOTE: Assemble as close
to assembled units final
desired location to avoid
moving a heavy unit.
B
T
MC
LC
E
For ease of assembly, it is
recommended to lay down
the end panel (E) as shown.
TURN
CLOCKWISE
1
Cam locks can be seen on the topside of the
bottom shelf when installing the bottom shelf.
Fasten Cam Locks in 6 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)
T
MC
LC
B
TURN
CLOCKWISE
TURN
CLOCKWISE
TURN
CLOCKWISE
NOTE: Before assembling each part, please make
sure cams are parallel to the side of the surface &
pins are nicely screwed with the collar touching the
edge of the part. (See page 3 for proper alignment
of parts)
Use mallet, before tightening cam screws, to bring
parts together and avoid light leaks.
®
Fasten Cam Locks in 9 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)

Page 5 of 12
939500279 Rev E
3
5
C
D
4
NOTE: Please adjust glides
for leveling after assembling
each sub unit (each opening). GLIDE
I
Fasten Cam Locks in 9 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)
TURN
CLOCKWISE
NOTE: Before assembling each part, please make sure cams
are parallel to the side of the surface & pins are nicely screwed
with the collar touching the edge of the part. (See page 3 for
proper alignment of parts)
Use mallet, before tightening cam screws, to bring parts
together and avoid light leaks.
®

2
GLIDE Page 6 of 12
939500279 Rev E
1
NOTE: Please adjust glides for
leveling after assembling each
sub unit (each opening).
I
T
MO
LO
Fasten Cam Locks in 9 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)
Fasten Cam Locks in 9 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)
TURN
CLOCKWISE
4
D
D
I
T
I
T
MO
LO
TURN
CLOCKWISE
MO
LO
3
NOTE: Before assembling each part, please
make sure cams are parallel to the side of
the surface & pins are nicely screwed with
the collar touching the edge of the part.
(See page 3 for proper alignment of parts)
Use mallet, before tightening
cam screws, to bring parts
together and avoid
light leaks.
®

Page 7 of 12
939500279 Rev E
3
NOTE: Please adjust glides for
leveling after assembling each
sub unit (each opening).
1
Cam locks can be seen on the topside of the
bottom shelf when installing the bottom shelf.
Fasten Cam Locks in 6 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)
T
MC
LC
B
E
TURN
CLOCKWISE
TURN
CLOCKWISE
TURN
CLOCKWISE
Fasten Cam Locks in 9 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)
E
For ease of assembly, it is
recommended to lay down
the end panel (E) as shown.
TURN
CLOCKWISE
2
MC
LC
T
B
GLIDE
NOTE: Before assembling each part, please
make sure cams are parallel to the side of
the surface & pins are nicely screwed with
the collar touching the edge of the part.
(See page 3 for proper alignment of parts)
Use mallet, before tightening cam screws, to
bring parts together and avoid light leaks.
®

Page 8 of 12
939500279 Rev E
4
D
Level units by adjusting
glides in 8 places.
For optional items, please refer
to the following:
Adjustable Shelf Installation,
See page 9
Moving a Back Panel from
one Opening to Another,
See page 10 and 11
Grommet Installation,
See page 12
36" Door, 72" Door and
Bar Pull Installation,
See Assembly Direction
939500262
T
MC
LC
B
E
NOTE: When assembly has been completed, make sure to remove
all of the E, B, I, ect. stickers from the surfaces of all the parts.
T
B
MC
LC
E
Fasten Cam Locks in 6 places
(The cam lock screw needs to be turned
3/4 full turn or 270oclockwise for
complete engagement.)
TURN
CLOCKWISE
NOTE: Before assembling each part, please
make sure cams are parallel to the side of
the surface & pins are nicely screwed with
the collar touching the edge of the part.
(See page 3 for proper alignment of parts)
Use mallet, before tightening cam
screws, to bring parts together and
avoid light leaks.
®

Page 9 of 12
939500279 Rev E
D
E
UNDERSIDE
OF SHELF
NOTCH
SHELF PIN
1
2
3
Adjustable Shelf
Installation
NOTE: The following is applicable to
all scenarios. 3 unit is shown as an
example.
1. Insert shelf pins into side of wall.
Repeat for other side.
2. Before inserting shelf into unit,
there are notches on the underside of
the shelf which the pin fits into.
3. Insert shelf.
A
A
A
®

Page 10 of 12
939500279 Rev E
Moving a Back Panel from
one Opening to Another
NOTE: The following is applicable to all
scenarios. 3 opening unit is shown as an
example. All three (3) fixed shelves can be
rotated 180oand the back panel can be
installed on the other side.
1. In this scenario, panel B is being
moved (1a). To begin to remove
the panel, proceed to the other
side of the unit and loosen
the cam locks in six (6)
places (1b).
D
E
D
D
D
1a
1b
LC
MC
T
B
Loosen Cam Locks in 6 places
(The cam lock screw needs to be turned
3/4 full turn or 270ocounter-clockwise for
complete removal.)
TURN
COUNTER-CLOCKWISE
®