Steelcase Ology FrameOne User manual

5/32”
5/32” HEX
T30
#2 SQUARE
Ology™FrameOne®End Panel
888.STEELCASE (888.783.3522)
www.steelcase.com
©2019 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
®
Page 1 of 11
1360037001 Rev A
5/32”
(with and without Utility Pole)

®
Page 2 of 11
Install Extension Box to Mounting Bracket
1a) If assembling frame one end panel with utility pole*,
then locate extension box to panel mounting bracket
(center on dual sided, left or right for single sided),
1b) install (4) .250-20 x .500
screws (provided) and fasten
securely. 1b
1a
1360037001 Rev A
Dual Sided
Single Sided RH
Single Sided LH
Frame One End Panel with Utility Pole
*If no Utility Pole, proceed to Step 2.

®
Page 3 of 11
Dual SidedSingle Sided
Assemble Mounting Bracket
2) Using (3) M6 button head thread forming screws (provided)
attach the mounting bracket to underside of cross-tube weldment.
TIP: Note hole positions used on single sided (see arrows),
centered on dual sided applications.
3a) Use a level to check for vertical orientation. 3b) Loosen
(6) button head screws using a 5/32" allen wrench, 3c) adjust
the interface bracket to vertical and 3d) retighten (6) button
head screws.
3d
3b
3c
5/32”
3a
1360037001 Rev A
2
.472"
(12mm)
3x

®
Page 4 of 11
1” minimum
Attach the Frame One End Panel
4a) Position Frame One End Panel against bracket and check for
alignment of the pilot holes (6X), 4b) adjust the leveler
glides, if necessary, to match the pilot hole pattern to slots in
bracket, 4c) secure using (6X) #10-12 x .625 screws (provided).
TIP: Check for 1” minimum gap clearance and alignment
to work surface top. If necessary, loosen screws from Step 2,
make adjustment to end panel position, then retighten screws securely.
4c 4a
TIP: If universal screens are applied on the bench and experiencing
interference with the center cap on end panel, remove the cap. The
infill mounting bracket is visually concealed by the end of the screen.
1360037001 Rev A
See Tip
4b

®
Page 5 of 11
Install Trim
5c
5b
5a
6a
6b
TIP: If a utility pole is to be installed and the extension box
was not assembled previously, do this now (see Step 1).
5a) Flex sides of trim cover open to overlap mounting bracket,
5b) engage “V-tabs” to slots, then 5c) push cover tight to
end panel.
6a) Install trim bezel over the extension box and
6b) press into the panel cutout opening.
1360037001 Rev A

®
Page 6 of 11
7a) Using a level positioned on center of the extension box,
7b) transfer a mark to the top frame tube member, 7c) drill a
5/32" hole in the frame tube at 1" down from your mark, as
illustrated. 7d) Install angle bracket using #10-12 x .625 screw
and washer (provided).
TIP: slot in bracket provides adjustment in and out.
7e) Adjust angle bracket in or out to align in-plane with
extension box below.
Install Angle Bracket
7a
7b
7c 7e
7d
1”
1360037001 Rev A
In-Plane with
Extension Box

®
Page 7 of 11
8a) Thread glide into pole base, then
8b) locate into bottom of aluminum column.
9a) Position column with glide base on the floor, and
9b) Adjust glide to align pass through opening and slots
to extension box installed in step 1, 9c) install
(4) .250- 20 x 1” hex socket button head cap screws
(provided) securing aluminum channel to the extension
box, 9d) install hex socket button head cap screw through
upper slot inside aluminum channel to angle bracket
installed in step 6d.
Attach Column
TIP: Install connector end of power harness through
cutout openings before data cables.
TIP: Remove ceiling tile if entering ceiling grid,
see step 10.
8a 8b
9a
9b
9d
9c
1360037001 Rev A

®
Page 8 of 11
3-1/4" x 6-1/4"
1-5/8"
3-1/8"
10) Remove the ceiling tile where the pole will be
placed and raise the utility "C" channel vertical.
11) Cut ceiling tile hole.
12) Assemble ceiling trim plate.
13) Bend retainers up and insert ceiling
trim plate into the ceiling tile cut-out.
Install Utility Pole into Ceiling 10
11
12
13
1360037001 Rev A

®
Page 9 of 11
14) Place ceiling tile with trim plate
back in ceiling.
15) Remove adjacent ceiling tile.
16) Insert the vertical channel through
the ceiling tile hole
NOTE: If the vertical channel extends above
the ceiling tile more than 4 inches mark and
cut excess material off before securing to
the frame or junction bracket. Deburr
exposed edges.
17) Route any power cords, harness and
data cables as needed.
Attach Column
14
15
1360037001 Rev A
4"
max 16

®
Page 10 of 11
18) Attach the ceiling bracket to the top of
the vertical channel.
19) Secure crossbar to the ceiling grid.
20) Attach slotted adjustment bracket to the
cross bar and fully tighten screw.
21) Attach slotted adjustment bracket to the
ceiling bracket. Be sure not to fully tighten
the screws.
Attach Column
1360037001 Rev A
5
of
9
8-18 x 1/4"
8-18 x 3/8"
8-18 x 1/4"
Gold #8-18 x .360"
18
19
21
20