Steelcase Secant User manual

Page 1 of 22
939504557 Rev T
Secant®Freestanding Worksurface Support
®
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2000 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
ACR l l
ll
ACR II #3 Bit
#3 Square Drive Bit
Use care during the staging and installation to 
prevent damage to finished surfaces.
Illustrator 9.0

Page 2 of 22
939504557 Rev T
1. For an end-of-run application,
attach each bracket to support
with two (2) screws in opposing
holes.
1a. NOTE: Change glides to
opposite end to change from one
hand to the other on end panel.







2. For a shared application, attach
each bracket to support with
two (2) screws using in-line holes.
Corner Support
Intermediate Support
End Panel Support
1a
Front worksurface screw location.
C-Leg Support

Page 3 of 22
939504557 Rev T
3. Attach one end of the stretcher to
one completed support assembly
with four (4) screws, then attach
opposite end of stretcher to adjacent
support assembly.

3a. When the intermediate support is
used in the center position of a single
worksurface, bend the tabs of the
intermediate support bracket so that
they are flush with Surface A.
Surface A

Page 4 of 22
939504557 Rev T
4. Attach appropriate plates to
intermediate and c-leg supports
with two (2) screws.

Page 5 of 22
939504557 Rev T
5. Align worksurface to support structure
fitting over projections and attach,
using screws as shown.
NOTE:
Adjust support side to side
position to minimize worksurface
mismatch.

Page 6 of 22
939504557 Rev T
6. Peel backing off double-sided tape
to expose sticky surface, then press wire
manager onto back side of support. This
is typical for all supports.
C-Leg Support Wire Manager

Page 7 of 22
939504557 Rev T
Conference Link and Conference
Wing Assembly

1.  For an end-of-run application, attach
each bracket to support with
two (2) screws in opposing holes.

2.  For a shared application, attach
each bracket to support with
two (2) screws using in-line holes.
Corner Support
Intermediate Support

Page 8 of 22
939504557 Rev T
Conference Link and Conference
Wing Assembly

3. Attach one end of the stretcher to one
completed support assembly with
four (4) screws, then attach opposite end
of stretcher to adjacent support assembly.
4. Attach post to conference link or
conference wing using (4) screws.
Conference wing
Conference link
NOTE:
Adjust support side to side
position to minimize work
surface mismatch.

Page 9 of 22
939504557 Rev T
Conference Link and Conference
Wing Assembly

5. Attach mounting plate to support.
6. Attach top with post to brackets.
7.  Attach wire manager as shown
in step 6 on page 6.
NOTE:
Adjust support side to side
position to minimize work
surface mismatch.

Page 10 of 22
939504557 Rev T
End Cap Assembly

1.  For end cap installation, attach each bracket
to support with two (2) screws using in-line holes.

2. Attach stretcher to support assembly with
four (4) screws.
3.  Install the mounting plate to support using
three (3) 1/4-20 flat head cross-recessed
machine screws.
C-Leg Support

Page 11 of 22
939504557 Rev T
4.  Attach end cap and adjoining worksurface to
mounting plate using three (3) #12 x 1" long
flat head wood screws in each surface.



5.  Attach worksurface straps at front and rear
of worksurface using one (1) #8 x 7/8" long
flat head wood screw in each surface.
Worksurface attachment holes
Install these (2) screws after front edges of
worksurfaces are aligned.

Page 12 of 22
939504557 Rev T
C-Leg Support
Corner Support
Intermediate Support
1. 2.
3.
Secant®Adjustable Height
Worksurface Support
1. For maintenance adjustable C-Leg
 supports only!
  a) Install glide assembly.
  b) Snap plastic cover over glide assembly.
2. For end-of-run applications, attach each
 bracket to support with four (4) screws.
3. For shared applications, attach each
 bracket to support with two (2) screws.
a
b

Page 13 of 22
939504557 Rev T
4. Attach one end of stretcher to one
completed support assembly with
four (4) screws, then attach opposite
end of stretcher to adjacent support
assembly. Continue until the entire
support structure is complete.
The nominal length of
the Corner Stretcher
is 6" shorter than the
nominal length of the
Corner Worksurface.

Page 14 of 22
939504557 Rev T
5. Attach mounting plate to supports with
three (3) 1/4-20 flat head cross-recessed
machine screws.

Page 15 of 22
939504557 Rev T
6. Attach mounting plate to supports with
three (3) 1/4-20 flat head cross-recessed machine
screws.
Use (4) screws on the mounting plate for C-Leg
end support.
Install these (2) screws after
front edge of worksurfaces
are aligned.

Page 16 of 22
939504557 Rev T
7. Peel backing off double-sided tape
to expose sticky surface, then press wire
manager onto back side of support. This
is typical for all supports.
C-Leg Support Wire Manager
1.
2.

Page 17 of 22
939504557 Rev T
Conference Link and Conference
Wing Assembly
1. For each end-of run application attach
each bracket to support with four (4) screws.
2. For a shared application, attach each
bracket to support with two (2) screws.
C-Leg Support
Intermediate Support

Page 18 of 22
939504557 Rev T
Conference Link and Conference
Wing Assembly

3. Attach one end of the stretcher to one
completed support assembly with four (4)
screws, then attach opposite end of stretcher to
adjacent support assembly.
4. Attach post to conference link or conference
wing using (4) screws.
Conference wing
Conference link
3.

Page 19 of 22
939504557 Rev T
Conference Link and Conference
Wing Assembly

5. Attach mounting plate to support.
6. Attach top with post to brackets.
7. Attach wire manager as shown
in step 6 on page 6.

Page 20 of 22
939504557 Rev T
Spanner worksurface
5. Connect supports with brackets.
Attach mounting plates to supports.
6. Align spanner worksurface to mounting
plates and attach using three (3) #12 x 1"
long flat head screws as shown.