Draper Targa Manual

Installation/Operating Instructions
220V Targa Electric Projection Screen by Draper
These Installation/Operating Instructions are available in the official language
of the country where you purchase the product. Please contact your distributor to
request a copy.
Vous pourriez demander les instructions d’installation et d’opération traduises
dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à
votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der offiziellen
Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen
Sie die jeweilige Verkaufs-Abteilung.
Operation
Before operating screen remove tape securing fabric and dowel to roller. If viewing
surface hangs out of case 22 or 23 mm, tape has probably been broken by rough
handling in shipment, allowing surface to “unwrap” one turn about the roller.
Manually wrap fabric back around roller without turning the roller itself.
Note: Drive unit contains a thermal overload protector. Operation as frequently
as six cycles per hour may trip the protector. If tripped, the protector should reset
automatically within a few minutes.
220V AC Single Station Control—3-position up-off-down switch permits
operation to be stopped at any point. Factory adjusted limit switches automatically
stop screen when fully down or fully up.
220V AC Multiple Station Control (Not CE approved)—Switches are similar in
appearance to 220V Single Station Control. Screen stops when switch is released
and may be restarted in either direction. Factory adjusted limit switches stop
screen automatically when fully up or fully down.
24V Control—Three-button up-stop-down switch(es) stop at any point desired,
operate in any sequence. Factory adjusted limit switches automatically stop screen
when fully up or fully down. Installer should incorporate an all-pole disconnect in
the fixed wiring.
Key Operated Switching (Not CE approved)—Two kinds of key-operated
switches are optionally available with this unit. ➀The key-operated power supply
switch controls power to the screen and switches. When it is “off”, the switches
will not operate screen. Key may be removed from the switch in either “on” or “off”
position. ➁A three-position key switch permits the screen to be operated directly
by key. In this case, the screen’s operator must always have a key.
RS232/Ethernet—Serial communication and network communication optionally
available with wall switches, RF or IR remote.
Electrical Connections
Screen operates on 220V AC, 50 Hz., 1 ph. current.
Junction box is located inside left endcap and cover plate is secured to endcap
with two screws. Junction box contains terminal strip, per wiring diagram on
reverse.
Screen is shipped with internal wiring complete and control switch(es) fully boxed.
Wire connecting screen to switch(es) and switch(es) to power supply should be
furnished by installer. Connections should be made in accordance with wiring
diagram supplied, and wiring should comply with national and local electrical
codes.
All operating switches should be “Off” before power is connected.
Adjustments
Screen has been factory set and should not normally require further adjustment.
However, if you desire to change the “up” and “down” stopping positions, proceed
as follows:
CAUTION: Be sure all switches are in “off” position before adjusting limit switches.
Always be prepared to shut screen off manually when new adjustment is being
tested. Screen may be severely damaged if viewing surface is allowed to run too
far up or too far down.
Adjusting “fully up” position — “Up” stopping position may be adjusted by
turning the UP limit switch adjustment socket. The UP socket is located on left
end of screen roller and is accessible to a screwdriver/Allen wrench (4mm or
5
/ 32 ").
Tu r n ing the socket counterclockwise will allow the viewing surface to retract farther
into the case. Turning it clockwise will cause surface to stop farther out of the
case. One full revolution of socket will alter stopping position of viewing surface by
approximately 4 cm.
Adjusting “fully down” position — “Down” stopping position may be adjusted by
turning the DOWN limit switch adjustment socket. The DOWN socket is located on
the left end of screen roller and is accessible to a screwdriver/Allen wrench (4mm
or
5
/ 32 "). Turning the socket counterclockwise will allow the viewing surface to run
farther down. Turning it clockwise will shorten viewing surface, causing it to stop in
a less extended position. At no time should viewing surface be unrolled enough to
expose any part of screen roller.
Copyright © 2009 Draper Inc. Form Targa220V_Inst09 Printed in U.S.A.
Hanging Screen
General: When locating viewing surface and checking clearance for screen’s
operation, remember surface is centered in case. Handle case carefully to protect
its finish.
Regardless of mounting method, screen should be positively and securely
supported so that vibration or even abusive pulling on the viewing surface will not
cause case to work loose or fall. Installer must insure that fasteners used are of
adequate strength and suitable for the mounting surface chosen.
Suspended Installation:
Suspend screens from holes in endcaps as shown. S-hooks, chains (or cable) and
turnbuckles should be provided by installer. “S” hooks should go through the front
holes on the endcaps (see drawing on page 2), and both ends of the “S” hooks
should be crimped for additional safety. Chains should be attached to beams or
other structural members. Turnbuckles should be adjusted so screen hangs level.
Wall Installation:
Mount screen through holes in back of endcaps as shown. Installer should furnish
screws, toggle bolts, molly bolts, nylon or lead anchors as required.
Wall Installation with 15 cm Extension Brackets:
Mount the brackets (not included with screen—see diagram below right) using
hardware recommended for “Wall Installation” (above). Then, suspend the screen
from the front holes with “S” hooks (as in “Suspended”). For added safety, crimp
both ends of the “S” hooks so the screen cannot come off. For a more rigid
installation, mount the screen from the back holes to the front of the bracket by
using the screws and nuts provided with the brackets.
Caution
➀Read instructions through completely before proceeding.
➁Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂Screen should be accessible for complete removal should fabric become
damaged or should other service be required.
➃Screen should be installed level (using a carpenter’s level).
➄Nothing should be fastened to screen dowel or viewing surface.
➅Operating switch(es) packed separately in screen carton. Do not discard
with packing material.
➆Screen operates on 220V AC, 50 Hz., 1 ph. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
®
Screen Case
Back
Ceiling Tile
(By others)
Recessed Installation:
Recess should permit access for removal of screen if necessary. Screen may
be mounted as in suspended or wall installation. Optional Ceiling Opening Trim
Kit available; see diagrams below and on page 2, and separate instruction sheet
(included with Ceiling Opening Trim Kit).
If you encounter any difficulties installing or servicing your Targa screen, call your dealer or
Draper, Inc. Spiceland, Indiana, U.S.A., telephone [phone] or fax [phone].
15 cm Extension
Bracket
15
cm

Targa 220V Instructions
Single Station Control
CE Approved
Terminal strip in
junction box at left
end of screen
Dashed wiring
by electrician
Neutral
L1
230V,
50 Hz.
Terminal strip in
junction box at left
end of screen
Dashed wiring
by electrician
Neutral
Hot
Multiple Station Control
Not CE Approved
Cap off with wire
nut & tape
Red
Red
Red
Blue
Blue
Blue
Black
Black
230V, 50 Hz.
Control
switch
Black
PE
220V Wiring Diagrams
Case Dimensions/Installation Diagrams
Page 2 of 2
Wall Mounted
Appropriate hardware
provided by installer.
Suspended
Appropriate hardware
provided by installer.
Fabric width + 192mm
Viewing
surface
96mm
22mm dia.
electrical
connection
hole
150mm
59mm
134mm
54 mm
67
mm
102 mm
162 mm
1.6
mm
203
mm
7/8" hole for
electrical
connection.
Fasteners for
wall mounting
by others.
S Hooks for
suspended
installation
by others.
Optional Ceiling Opening Trim Kit
(Dims-Side View)
Methods of Installation
www.draperinc.com (765) 987-799
9
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Eye Port for IR Eye, RF Receiver or LED
Switch For more than one of these,
a splitter is required.
Aux Port for connecting additional
LVC-III modules (up to six total-
connect from Aux to Eye).
Red-to screen (directional)
Brown-to screen (directional)
White-Common to screen, 230V AC
Black-to 230V AC
Yellow-to 230V AC
Green-Ground
Dashed wiring by electrician
Low voltage wiring by others
Terminal strip in
junction box at left
end of screen
230V, 50 Hz.
Neutral
Hot
All-Pole Disconnect
by Others
STOP
Control
Switches
24v DC
STOP
MC1
See separate Serial Communication-
RS232 Instruction sheet for enabling
RS232 with the MC1.
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Red-to Screen (directional)
Black-to Screen (directional)
Blue-Common
Brown-Hot to 230V AC
Green/Yellow-Ground
Fuse
Program LED
Eye Port for IR Eye. For RF Receiver
or LED Wall Switch, a Splitter and a
Power Supply is required. Plug RF
Receiver or LED Wall Switch and
Power Supply into splitter, then run
cable from Splitter to MC1 Eye Port.
Low Voltage Wiring by others
AC Wiring by electrician
MC1
Terminal strip in
junction box at left
end of screen
230V, 50 Hz.
Neutral
Hot
All-Pole Disconnect
by Others
STOP
Control
Switches
24v DC
STOP
Low Voltage & Remote Control (LVC-III)
Crimp
both
ends