STI STOPPER SS2 0 Series User manual

*SS2xx4 and LT1-UL NOTES: For access control installations, power for the LT-1UL Timer must be supplied by a
power source listed to UL294. When used for access control, this device shall be used as part of an access controlled
egress door system. It is up to the local AHJ to allow use of this device in place of an automatic sensor. For higher
security installations, lower time limits should be used. For SS2xx4 and LT1-UL the enclosed timer is to be used and
installed per the enclosed LT-1UL installation sheet. *SS2xx4 and LT1-UL maximum rating 30 VDC 3A.
REMARQUES POUR *SS2xx4 et LT1-UL: Pour les installations de contrôle d’accès, l’alimentation de la
minuterie LT-1UL doit être fournie par une source homologuée UL294. Lorsque cet appareil est utilisé aux
ns de contrôle d’accès, il doit faire partie d’un système de porte de sortie à accès contrôlé. Il incombe donc
à l’AHJ local d’autoriser l’utilisation de cet appareil au lieu d’un capteur automatique. Pour les installations
de sécurité plus renforcée, des délais inférieurs doivent être utilisés. Pour les modèles SS2xx4 et LT1-
UL, la minuterie intégrée doit être installée et utilisée suivant la che d’installation LT-1UL fournie. La cote
maximale des modèles *SS2xx 4 et LT1-UL est de 30 VCC 3A.
WARNING: This product can expose you to chemicals including Bisphenol A, which is known to the State of
California to cause reproductive harm and Dichloromethane, which is known to the State of California to cause
cancer. For more information go to www.P65Warnings.ca.gov.
Three year warranty or a one year limited warranty (from date of purchase) on most products.
See website for details. Electronic warranty form at www.sti-usa.com/wc14.
1027IS OCT2018
INSTALLATION OF SS2xx0, SS2xx1, SS2xx3, SS2xx4 SERIES STOPPER® STATION
All specications and information shown were current as of publication, and are subject to change without notice.
NC
NO
1
2
3
4
STRIP 1/4 in. OF WIRE INSULATION
INSERT IN TERMINAL (AS SHOWN) THEN
USING A PHILLIPS SCREWDRIVER TURN
CLOCKWISE UNTIL TIGHT.
SEPARATION OF TERMINAL ASSEMBLY.
FROM BUTTON ASSEMBLY IS AS FOLLOWS:
GRASP TERMINAL HOUSING AND USING THUMB
APPLY PRESSURE DOWNWARD, REMOVE TERMINAL.
REMOVAL OF TERMINAL BLOCK
FROM TERMINAL HOUSING: INSERT
SMALL SCREWDRIVER (AS SHOWN)
AND PRY UPWARD, REMOVE TERMINAL.
TERMINAL BLOCK
RELEASE LEVER
MUST FACE UPWARD
AS SHOWN FOR SWITCH
TO FUNCTION CORRECTLY.
ELECTRICAL TERMINAL BLOCK
UP TO 3 TERMINALS MAY BE USED
INSERT NOTCH, AS SHOWN
THEN ROTATE UPWARD
TERMINAL BLOCK KIT-E10196 NO (1) PROVIDED
KIT-E10198 NC (1) PROVIDED
SEE VIEW IN DIRECTION OF ARROW
FOR CONTACT INDENTIFIER LOCATIONS
UP TO (3) TERMINALS MAY BE USED FOR EACH
STATION ASSEMBLY.
OUTGOING
INCOMING
SCREWS #6-32 x 1
OUTLET BOX (2) PROVIDED.
SCREWS #6-32 x 1.50 WHEN
USING KIT-102722-COLOR SPACER
(SEE REVERSE SIDE).
#10-32 x 3/8 in. GROUND SCREW
(1) PROVIDED
BUTTON LOCK NUT
BACKPLATE
A
EXISTING STANDARD
SINGLE GANGBOX
HOUSING INDEXING SLOTS
BACKPLATE ASSEMBLY
(SEE REVERSE SIDE)
5/8” SPACER
KIT-102722-B (BLUE)
KIT-102722-G (GREEN)
KIT-102722-R (RED)
KIT-102722-W (WHITE)
KIT-102722-Y (YELLOW)
WHITE M10274-W
OCTAGON SHELL
E10105 MOMENTARY BUTTON (#4)*KIT-H18062 KEYS
(2) PROVIDED
M10271 STATION SHELL
RED, GREEN, YELLOW,
WHITE, BLUE AND ORANGE
E10100 PUSH/TURN
RESET BUTTON (#1)
KEY BUTTON (#3)
KEY REQUIRED TO ACTIVATE - IN
ACTIVATE MODE KEY CAN BE REMOVED
#8-32 x 3/8 in. BUTTON HEAD
SCREW (1) PROVIDED
KIT-H19030 KEYS
(2) PROVIDED
E10102 KEY RESET SWITCH
OCTAGON KEY RESET BUTTON (#0)
RED, GREEN, YELLOW, WHITE
AND BLUE
M02050
PUSH
PUSH
HERE
MESSAGE
AREA
NOTE: TO PROVIDE ADEQUATE
CLEARANCE FOR INSTALLATION,
MAY REQUIRE: KIT-102722 5/8” SPACER
PRODUCT DIMENSIONS
3.25 in.
(82mm)
4.87 in.
(124mm)
1.62 in.
(41mm) 2.25 in.
(57mm)
“A”
UL294 Performance Levels:
Line Security: I
Attack: I
Endurance: IV
Standby Power: I
USA EMEA

1027IS OCT2018
INSTALLATION OF SS2xx0, SS2xx1, SS2xx3, SS2xx4 SERIES STOPPER® STATION
All specications and information shown were current as of publication, and are subject to change without notice.
ALL TERMINALS ACCEPT TWO 12 TO 18 (AWG)
VOLTAGE AVERAGE CURRENT
250 VDC 1 AMP
600 VAC 3 AMP
NOTE: SS-2XX4/LT CONTACTS ON FORM C TIMER RATED: 120 VAC, 3A
28 VDC, 3A
NC
NO
1
2
3
4
STRIP 1/4 in. OF WIRE INSULATION
INSERT IN TERMINAL (AS SHOWN) THEN
USING A PHILLIPS SCREWDRIVER TURN
CLOCKWISE UNTIL TIGHT.
SEPARATION OF TERMINAL ASSEMBLY.
FROM BUTTON ASSEMBLY IS AS FOLLOWS:
GRASP TERMINAL HOUSING AND USING THUMB
APPLY PRESSURE DOWNWARD, REMOVE TERMINAL.
REMOVAL OF TERMINAL BLOCK
FROM TERMINAL HOUSING: INSERT
SMALL SCREWDRIVER (AS SHOWN)
AND PRY UPWARD, REMOVE TERMINAL.
TERMINAL BLOCK
RELEASE LEVER
MUST FACE UPWARD
AS SHOWN FOR SWITCH
TO FUNCTION CORRECTLY.
ELECTRICAL TERMINAL BLOCK
UP TO 3 TERMINALS MAY BE USED
INSERT NOTCH, AS SHOWN
THEN ROTATE UPWARD
TERMINAL BLOCK KIT-E10196 NO (1) PROVIDED
KIT-E10198 NC (1) PROVIDED
SEE VIEW IN DIRECTION OF ARROW
FOR CONTACT INDENTIFIER LOCATIONS
UP TO (3) TERMINALS MAY BE USED FOR EACH
STATION ASSEMBLY.
OUTGOING
INCOMING
SCREWS #6-32 x 1
OUTLET BOX (2) PROVIDED.
SCREWS #6-32 x 1.50 WHEN
USING KIT-102722-COLOR SPACER
(SEE REVERSE SIDE).
#10-32 x 3/8 in. GROUND SCREW
(1) PROVIDED
BUTTON LOCK NUT
BACKPLATE
A
EXISTING STANDARD
SINGLE GANGBOX
HOUSING INDEXING SLOTS
BACKPLATE ASSEMBLY
(SEE REVERSE SIDE)
5/8” SPACER
KIT-102722-B (BLUE)
KIT-102722-G (GREEN)
KIT-102722-R (RED)
KIT-102722-W (WHITE)
KIT-102722-Y (YELLOW)
WHITE M10274-W
OCTAGON SHELL
E10105 MOMENTARY BUTTON (#4)*KIT-H18062 KEYS
(2) PROVIDED
M10271 STATION SHELL
RED, GREEN, YELLOW,
WHITE, BLUE AND ORANGE
E10100 PUSH/TURN
RESET BUTTON (#1)
KEY BUTTON (#3)
KEY REQUIRED TO ACTIVATE - IN
ACTIVATE MODE KEY CAN BE REMOVED
#8-32 x 3/8 in. BUTTON HEAD
SCREW (1) PROVIDED
KIT-H19030 KEYS
(2) PROVIDED
E10102 KEY RESET SWITCH
OCTAGON KEY RESET BUTTON (#0)
RED, GREEN, YELLOW, WHITE
AND BLUE
M02050
PUSH
PUSH
HERE
MESSAGE
AREA
NOTE: TO PROVIDE ADEQUATE
CLEARANCE FOR INSTALLATION,
MAY REQUIRE: KIT-102722 5/8” SPACER
PRODUCT DIMENSIONS
3.25 in.
(82mm)
4.87 in.
(124mm)
1.62 in.
(41mm) 2.25 in.
(57mm)
“A”
NC
NO
1
2
3
4
STRIP 1/4 in. OF WIRE INSULATION
INSERT IN TERMINAL (AS SHOWN) THEN
USING A PHILLIPS SCREWDRIVER TURN
CLOCKWISE UNTIL TIGHT.
SEPARATION OF TERMINAL ASSEMBLY.
FROM BUTTON ASSEMBLY IS AS FOLLOWS:
GRASP TERMINAL HOUSING AND USING THUMB
APPLY PRESSURE DOWNWARD, REMOVE TERMINAL.
REMOVAL OF TERMINAL BLOCK
FROM TERMINAL HOUSING: INSERT
SMALL SCREWDRIVER (AS SHOWN)
AND PRY UPWARD, REMOVE TERMINAL.
TERMINAL BLOCK
RELEASE LEVER
MUST FACE UPWARD
AS SHOWN FOR SWITCH
TO FUNCTION CORRECTLY.
ELECTRICAL TERMINAL BLOCK
UP TO 3 TERMINALS MAY BE USED
INSERT NOTCH, AS SHOWN
THEN ROTATE UPWARD
TERMINAL BLOCK KIT-E10196 NO (1) PROVIDED
KIT-E10198 NC (1) PROVIDED
SEE VIEW IN DIRECTION OF ARROW
FOR CONTACT INDENTIFIER LOCATIONS
UP TO (3) TERMINALS MAY BE USED FOR EACH
STATION ASSEMBLY.
OUTGOING
INCOMING
SCREWS #6-32 x 1
OUTLET BOX (2) PROVIDED.
SCREWS #6-32 x 1.50 WHEN
USING KIT-102722-COLOR SPACER
(SEE REVERSE SIDE).
#10-32 x 3/8 in. GROUND SCREW
(1) PROVIDED
BUTTON LOCK NUT
BACKPLATE
A
EXISTING STANDARD
SINGLE GANGBOX
HOUSING INDEXING SLOTS
BACKPLATE ASSEMBLY
(SEE REVERSE SIDE)
5/8” SPACER
KIT-102722-B (BLUE)
KIT-102722-G (GREEN)
KIT-102722-R (RED)
KIT-102722-W (WHITE)
KIT-102722-Y (YELLOW)
WHITE M10274-W
OCTAGON SHELL
E10105 MOMENTARY BUTTON (#4)*KIT-H18062 KEYS
(2) PROVIDED
M10271 STATION SHELL
RED, GREEN, YELLOW,
WHITE, BLUE AND ORANGE
E10100 PUSH/TURN
RESET BUTTON (#1)
KEY BUTTON (#3)
KEY REQUIRED TO ACTIVATE - IN
ACTIVATE MODE KEY CAN BE REMOVED
#8-32 x 3/8 in. BUTTON HEAD
SCREW (1) PROVIDED
KIT-H19030 KEYS
(2) PROVIDED
E10102 KEY RESET SWITCH
OCTAGON KEY RESET BUTTON (#0)
RED, GREEN, YELLOW, WHITE
AND BLUE
M02050
PUSH
PUSH
HERE
MESSAGE
AREA
NOTE: TO PROVIDE ADEQUATE
CLEARANCE FOR INSTALLATION,
MAY REQUIRE: KIT-102722 5/8” SPACER
PRODUCT DIMENSIONS
3.25 in.
(82mm)
4.87 in.
(124mm)
1.62 in.
(41mm) 2.25 in.
(57mm)
“A”
EMEA
USA