STI UB-1PN User manual

ADA
for operation
UB-1PN Uni ersal
Pneumatic Button
We protect the things that protect you.

- 2 -
NOTES
It is important to read, understand and follow all instructions provided with this
product. It is the installer’s responsibility to comply with NFPA 70 & 101, NEC,
mounting specifications according to ADA and other applicable electrical
codes. To avoid electrical shock, DO NOT attempt to install this product when
power is on. ADA mounting compliance requires the operable part of the
initiating device shall not be less than 3 1/2 ft. (1.1m ) or greater than 4 1/2 ft.
(1.37m) above finished floor surface. After installation and testing are complete,
provide a copy of this manual to all personnel responsible for testing and
maintenance of this product.
* For access control installations, power for the UB-1PN must be supplied by a
power source Listed to UL294. When used for access control, this device shall
be used as a part of an access controlled egress door system. It is up to the
local AHJ to allow use of this device in place of an automatic sensor. For higher
security installations, lower time limits should be used.
SWITCH RATING Independent Form “Z” contacts
Rated at: 10A @ 240 VAC
Operating Temp: 15° to 120°F (-9° to 49°C)
1,000,000 Cycles
4.83 in.
(123mm)
3.22 in.
(82mm) .91 in.
(23mm)
1.47 in.
(38mm)

- 3 -
1. Choose button message and color. If same as existing, proceed to
2. If choosing a new message, remove button. On the back side of the plate,
squeeze tabs and push actuator assembly into plate just enough to grasp the
button and remove.
3. From the front of the plate, push actuator back into original position.
4. Choose button message. Blank plate is available for your custom message.
a. Insert button message, align 4 notches on actuator.
b. Select color lens. Align top and bottom notches with tabs on
actuator and push until it snaps together.
TO CHANGE BUTTON COLOR AND ROUND MESSAGE
CHANGE TOP MESSAGE
1. Remove LED circuit board.
2. Remove current message by pushing in and
down on tabs 1 and 2 with a small
screwdriver. If necessary, also push in and
down on tabs 3 and 4. Once message is loose,
remove from the front of the plate.
3. Select new message and snap into place.
Blank plates are included to create your own
custom message.
DIFFUSER
BUT
BUT
BUT
12
34
SCREWDRIVER
1
BUT
BUTTON ACTIVATED
M
UB-1L LED PCB
NYLON WASHER
SCREW
1
2
2
SQUEEZE TABS
AND PUSH
ASSEMBLY
INTO PLATE
POWERIN
12-30VDC/VAC

- 4 -
INSTALL
To attach, align tabs (as shown)
and gently snap top, then bottom.
Be sure to hear BOTH tabs snap
into place. Contacts can be rotated
180° if desired.
INSTALL OR REMOVE CONTACT BLOCK
REMOVE
To remove, use a
small flat blade
screwdriver.
Position screwdriver
blade under tab and
gently rotate
screwdriver until tab
disengages. Repeat
for opposite tab.
3
POWERIN
12-30VDC/VAC
BUTTON ACTIVATED
M
POWER IN
12-30 VDC/VAC
A
BUTTON ACTIVATED
M
POWER IN
12-30 VDC/VAC
BUTTON ACTIVATED
M
CONTACT INFORMATION
CONTACT REMOVAL
DETAIL A

- 5 -
ATTACH POWER FOR LED (IF DESIRED)
(See drawing)
4
BUTTON ACTIVATED
M
OFF
ON
+
+
+
MAG LOCK
NC CONTACTS
NO CONTACTS
UB-1L LED PCB
UL Listed
12-24 VDC Power Supply
NORMAL POSITION BUTTON ACTIVATED
ON
OFF
MAGNETIC LOCK
MESSAGE LAMP
BUTTON ACTIVATED
M
(BLACK) NC
(RED) NO
NC (GREEN)
NO (WHITE)
BUTTON ACTIVATED
M
NC
NO
NC
NO
CONTACT DIAGRAM
CONTACTS
One set NO nd one set NC

- 6 -
COUNTERCLOCKWISE
CLOCKWISE
TIMER RANGE ADJUSTMENT SCREW
ADJUSTMENT RANGE - 2 TO 60 SECONDS
TIMER FACTORY SET TO MINIMUM TIME
SETTING. TO INCREASE TIME, TURN
SCREW CLOCKWISE IN 1/4 TURN
INCREMENTS. WHEN CLOSE TO DESIRED
TIME, TURN SCREW IN VERY FINE
INCREMENTS TO DESIRED SETTING.
CAUTION: OVER-TIGHTENING MAY
CAUSE DAMAGE TO TIMER.
SWITCH INFORMATION
MOUNT BUTTON ONTO
ELECTRICAL BOX
5
BUTTON ACTIVATED
M
CUSTOM LABELS
To create your own custom label, size to fit in .48h x 2.23w as
shown below.
Also available online at: www.sti-usa.com/ublabel
2.23 in.
.48 in.
6

- 7 -
CONTACT BLOC
COLOR MATCH BAC BOX IT
CUSTOM LABEL APPLIED TO BLAN
MESSAGE PLATES
24 VOLT LED
WHITE (STANDARD)
RED
BLUE
GREEN
12 VOLT LED
RED
BLUE
GREEN
COVERS
BOPPER STOPPER
UNIVERSAL STOPPER
STOPPER II
SUB-UB-1PNC
SUB-71100A-COLOR
(red, blue, green, white or yellow)
UB-1CL-COLOR
(blue, green, white or yellow)
KIT-E10147
KIT-E10145
KIT-E10141
KIT-E10143
KIT-E10144
KIT-E10140
KIT-E10142
STI-6518
STI-13000 Series
STI-1100 Series
ACCESSORIES
DESCRIPTION PART #
See website for complete cover details

2306 Airport Rd • Waterford, MI 48327
Phone: [phone] • Fax: [phone]
[email protected] • www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England
Tel: [phone] • Fax: [phone]
E-mail: [email protected] • Web: www.sti-emea.com
Inst. Sht. UB-1PN Button JUN2018
WARRANTY
Three year guarantee against breakage of polycarbonate in normal use
(one year on electro mechanical and electronic components).
Electronic warranty form at www.sti-usa.com/wc14.
USA - Headquarters