Stinger HEIGH10 UN1810E-FD5 User manual

Copyright © 2023 StingerElectronics-EU.com
INTEGRATED INFOTAINMENT TOUCH SCREEN SOLUTION FOR
FORD TRANSIT CUSTOM 2018 >
PART NUMBER: UN1810E-FD5
INSTALLATION GUIDE

2
www.sngerelectronics-eu.com
ABOUT THIS PRODUCT
Upgrade your Ford Transit’s radio with the HEIGH10® 10-inch infotainment system. Retain all OEM features, vehicle
sengs, and more. All in one easy to install, plug-and-play package.
The HEIGH10® is designed to enhance screen size and infotainment features for drivers which include Apple CarPlay,
Android Auto, DAB+, and Bluetooth streaming. Paired with the vehicle retenon interface, key vehicle sengs will be
retained and controlled through the HEIGH10® display by your steering wheel controls.
The components of this kit are compable for the Ford Transit Custom MK1 Faceli 2018 >

CONTENTS
• HEIGH10® unit with ng accessories and wiring
• Black double DIN fascia plate (with accessories)
• Vehicle retenon interface with plug-and-play harness
• Vehicle specic antenna adapter (AM/FM/DAB)
• Snger stereo patch lead
• Instrucon manual

3
www.sngerelectronics-eu.com
FITTING GUIDE
STEREO REMOVAL
Turn o the ignion and remove the key from the vehicle.
Locate the trim panel around the radio on the dashboard. It should be a rectangular panel that surrounds the
radio and extends to the vents on either side of the radio. This will need to be removed as a complete unit.
Carefully pry o the trim panel using a plasc trim removal tool. Start at the boom of the panel and work your
way up, releasing the clips that hold the panel in place.
Disconnect the wiring harness and antenna cable from the back of the radio by pressing down on the tabs on
the connectors and pulling them out.
Once the trim panel is removed, you should see four tabs holding the radio in place. Carefully pry o the trim
panel using a plasc trim removal tool.
The radio should now be completely disconnected from the vehicle and can be removed.

4
www.sngerelectronics-eu.com
FITTING GUIDE
Take the HEIGH10® components and begin to assemble the core components in accordance with the “Installaon
Manual” that comes with unit.
HEIGH10 ASSEMBLY

5
www.sngerelectronics-eu.com
FITTING GUIDE

1. With the HEIGH10® unit congured correctly, aach the fascia brackets to the relevant sides of the radio module
using the screws within the kit. Place into the vehicle and roughly test t with the fascia to measure whether the
brackets need moving forwards/backwards.
2. With the brackets aligned correctly, aach the fascia to the brackets over the top of the unit using the screws that
come within in the kit.
3. Once all of the steps in ‘Stereo Installaon’ are complete, place the assembly into the dashboard and screw down
using the pre-exisng screws. Then reassemble the main fascia panel.
5. Aach the antenna adapter to the vehicles pre-exisng connecon and the back of new HEIGH10® unit.
2. Take the 14-way connector on the vehicle interface harness and plug this into the relevant connecon on the side
of the interface.
3. Take the 12-way connector of the stereo patch lead and plug this into the relevant connecon on the side of the
interface. Then take the 3.5mm jack and aach this to the HEIGH10® unit.
4. Aach the 4-way camera extension harness to the interface.
6. Aach the USB retenon lead in between the vehicle pre-exisng USB connector and the HEIGH10® unit.
7. Connect the male yellow RCA to the ‘reverse camera input’ on the back of the new stereo.
9. Aach the addional wiring on the harness to the back of the stereo:
- Speed Pulse  - Park Brake  - Reverse
10. When all the above wires (and any addional accessories) have been connected, nally make the power connec-
ons between the stereo and the vehicles pre-exisng connector.
For a full connecon breakdown of the HEIGH10® unit, see the “Installaon Manual” that comes with the unit.
8. Connect the aermarket reverse camera (if required) to the female yellow RCA on the camera extension harness.
Note: ensure the ‘Camera Connected’ opon in the ‘Preferences’ menu is set to ‘Yes’ for the camera to funcon cor-
rectly.

6
www.sngerelectronics-eu.com
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation
must be free of moisture and away from heat sources. Please ensure that the correct tools are using during the
installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation
of this product.
IN WIRING HARNESS
Purple Right Rear Speaker +
Purple/Black Right Rear Speaker -
Green Left Rear Speaker +
Green/Black Left Rear Speaker -
Grey Right Front Speaker +
Grey/Black Right Front Speaker -
White Left Front Speaker +
White/Black Left Front Speaker -
ADDITIONAL CONNECTIONS
Lt. Green Park Brake
Pink Speed Pulse
Purple/White Reverse Gear
WIRING KEY
STEERING WHEEL CONTROL FUNCTIONALITY
The following diagram, though based on careful research, is an example only. Individual steering wheel control congurations may differ.
Yellow Permanent 12V
Black Ground
Red Ignition 12V
Orange Illumination
1. Voice Assistant (*if software update performed)
2. Track - (Short Press)
Pick Up (Long Press)
3. Track + (Short Press)
Hang Up (Long Press)
4. Volume -
5. Volume +
6. Mute
SRC
MODE
VOL
VOL
1
4
2
3
6
5
*Visit www.connects2.com for more information on how
to download the SWC software update. Note: a reflasher
tool is also required (Part No: SWCREFLASHER)

7
www.sngerelectronics-eu.com
INSTALLATION GUIDE
Before installing the interface, the factory stereo must be removed and disconnected. To do this, please consult
the vehicle owner’s manual/handbook or contact a tting professional.
A stereo connection (patch) lead is also required for the installation of this interface (supplied separately).
Please ensure that you have the correct lead before proceeding. For universal patch leads, prepare the wiring
loops in accordance with the instruction manual supplied with the product before installation.
1. Connect the 12 Pin connector from the stereo connection (patch) lead to the interface box
See wiring diagram on Pg.4 for more information
2. Connect the opposite end of the stereo connection (patch) lead to the steering wheel control input on
the back of the aftermarket stereo
NOTE: This may be a 3.5mm jack connector or a wired input depending on the brand of aftermarket stereo being tted. Please consult the
aftermarket stereo installation manual for further information on where to make the connection
IMPORTANT: THIS STEP MUST BE COMPLETED BEFORE CONNECTING POWER TO THE INTERFACE.
FAILURE TO DO SO MAY RESULT IN A LACK OF FUNCTIONALITY AND THE NEED TO REINSTALL THE
PRODUCT
!
3. Connect the 14 Pin connector from the supplied wiring loom to the interface box
4. Connect the power/speaker ISO connector from the interface to the power/speaker ISO connector from
the aftermarket stereo.
NOTE: For aftermarket stereos which do not have an ISO connector, please see “Wiring Key” on Pg.2 for information on which wires to
connect. Some interfaces may also have additional ‘flying’ wires which can be connected to the vehicle to support various features
ie. parking brake trigger, reverse gear and speed pulse. Details of these can be found under ‘Additional Connections’.
5. Connect the 32 pin vehicle specic connector on the supplied harness to the connectors from the
vehicle. Please refer to wiring diagram on Pg.4 for more information.
6. Test stereo and steering wheel control functionality for correct operation before reassembling the
vehicle dashboard. If steering wheel control functions are unresponsive, please uninstall the interface and
wiring and reinstall carefully in accordance with the above steps.

8
www.sngerelectronics-eu.com
WIRING DIAGRAM
Male ISO Connector
Connect to aftermarket stereo
Vehicle Specific Connector [32 Pin]
Connect to corresponding connector from vehicle
Stereo Connection (Patch) Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected first, before power connection is
made to the interface
Main Wiring Loom Connector [14 Pin]
Connect to Interface Box
Interface Box
Flying Wires
Purple/White - Reverse Gear
Lt. Green - Park Brake
Pink - Speed Pulse

9
www.sngerelectronics-eu.com
For further help or assistance, please contact and ll out a support cket with full details of your issue via :

For general enquires, contact us at:
Phone: [phone]
E-Mail: 
Mon - Fri 9am - 5.30pm GMT
TECHNICAL ASSISTANCE
If you would like to download a digital copy of this manual, or any other product, then please visit the www.Snger-
Electronics-EU.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest manuals & updates,
refer to our website.
Copyright 2023 by Snger.
AGREEMENT: End user agrees to use this product in compliance with the instrucons and terms of use and with all laws.
STINGER provides instrucons and safety warnings with respect to this product and disclaims all liability for any use not in
conjuncon with those instrucons or other misuse of its product. If you do not agree, please disconnue use and contact
STINGER. This product is intended for o-road use and passenger use only.