Stinger HEIGH10 UN1810E-FT3 User manual

Copyright © 2023 StingerElectronics-EU.com
INTEGRATED INFOTAINMENT TOUCH SCREEN SOLUTION FOR
FIAT DUCATO SERIES 7 2014 - 2021
OPEN DASH VEHICLES ONLY
PART NUMBER: UN1810E-FT3
INSTALLATION GUIDE
If you would like to download a digital copy of this manual, or any other product, then please visit the
www.SngerElectronics-EU.com website.
This manual is considered correct at the me of prinng but is subject to change.
For the latest manuals & updates, refer to our website.
Legal Informaon
Please consult the relevant road trac laws governing the country in which this product is being operated.
No liability is accepted for material damage, loss or personal injury, directly or indirectly, from installaon and
operaon of this product. This product should only be operated when safe to do so.

2
www.sngerelectronics-eu.com
ABOUT THIS PRODUCT
Upgrade your Fiat Ducato’s radio with the HEIGH10® 10-inch infotainment system. All in one easy to install, plug-and-play
package.
The HEIGH10® is designed to enhance screen size and infotainment features for drivers which include Apple CarPlay,
Android Auto, DAB+, and Bluetooth streaming. Paired with the vehicle retenon interface, key vehicle sengs will be
retained and controlled through the HEIGH10® display by your steering wheel controls.
The components of this kit are compable for the Fiat Ducato Series 7 2014 - 2021 , open dash vehicles only.
CONTENTS
• HEIGH10® unit with ng accessories and wiring
• Black double DIN fascia plate (with accessories)
• Vehicle retenon interface with plug-and-play harness
• Vehicle specic antenna adapter (AM/FM)
• Snger stereo patch lead
• Instrucon manual
For help or assistance, please contact and ll out a support cket with full details of your issue via:
uktechnic[email protected]
For general enquires, contact us at:
Phone: [phone]
E-Mail: snger[email protected]om
Mon - Fri 9am - 5.30pm GMT
TECHNICAL ASSISTANCE

3
www.sngerelectronics-eu.com
FITTING GUIDE
Take the HEIGH10® components and begin to assemble the core components in accordance with the “Installaon
Manual” that comes with unit.
HEIGH10 ASSEMBLY
FITTING GUIDE
FASCIA PLATE SET-UP
1. With the HEIGH10® unit congured correctly, aach the fascia brackets to the relevant sides of the radio module
using the screws within the kit. Place into the vehicle and roughly test t with the fascia to measure whether the
brackets need moving forwards/backwards.
2. With the brackets aligned correctly, aach the fascia to the brackets over the top of the unit using the screws that
come within in the kit.
3. Once all of the steps in ‘Stereo Installaon’ are complete, place the assembly into the dashboard and screw down
using the pre-exisng screws. Then reassemble the main fascia panel.
WIRING COLOUR CODES
Purple Right Rear Speaker +
Purple/Black Right Rear Speaker -
Green Le Rear Speaker +
Green/Black Le Rear Speaker -
Grey Right Front Speaker +
Grey/Black Right Front Speaker -
White Le Front Speaker +
White/Black Le Front Speaker -
Yellow Permanent 12V
Black Ground
Red Ignion 12V
INTERFACE SET-UP

4
www.sngerelectronics-eu.com
1. Remove and disconnect the original head unit.
2. Connect the 12 way molex connector of the head unit patch lead (supplied separately) to the interface.
3. Connect the opposite end of head unit patch lead to the head unit steering
wheel control input on the back of the aermarket head unit.
NB: This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being ed. Please see the
head unit installaon manual for further informaon on
where to connect.
Important: This step must be completed before connecng power to the interface. Failure to so do may result in no
steering wheel control funcon.
4. Connect the 14 way molex connector to the interface
5. Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aermarket
head unit. For aermarket head units without an ISO
Copyright 2023 by Snger.
AGREEMENT: End user agrees to use this product in compliance with the instrucons and terms of use and with all laws.
STINGER provides instrucons and safety warnings with respect to this product and disclaims all liability for any use not in
conjuncon with those instrucons or other misuse of its product. If you do not agree, please disconnue use and contact
STINGER. This product is intended for o-road use and passenger use only.
STEERING WHEEL CONTROL FUNCTIONALITY
6. Connect the female vehicle specic connectors on the harness to the male vehicle connector from the vehicle.
Test head unit for correct operaon.
Funcon
Volume +
Volume -
Mute
Source
Original Buon
Plus Icon
Minus Icon
Mute
Speech
Track +
Track -
Pick Up
Hang Up
Up Arrow
Down Arrow
Pick Up
Hang Up