Stinger HEIGH10 UN1810E-VW3 User manual

Copyright © 2023 StingerElectronics-EU.com
INTEGRATED INFOTAINMENT TOUCH SCREEN SOLUTION FOR
VW Transporter T6 (MIB/PQ) 2015-2019
PART NUMBER: UN1810E-VW3
INSTALLATION GUIDE

2
www.sngerelectronics-eu.com
ABOUT THIS PRODUCT
Upgrade your VW Transporter’s radio with the HEIGH10® 10-inch infotainment system. Retain all OEM features, vehicle
sengs, and more. All in one easy to install, plug-and-play package.
The HEIGH10® is designed to enhance screen size and infotainment features for drivers which include Apple CarPlay,
Android Auto, DAB+, and Bluetooth streaming. Paired with the vehicle retenon interface, key vehicle sengs will be
retained and controlled through the HEIGH10® display by your steering wheel controls.
The components of this kit are compable for the VW Transporter T6 2015-2019, with non-amplied MIB/PQ Quadlock
factory head units.
Please note: this installaon kit is for faceli models, and will not work with amplied vehicles.
CONTENTS
• HEIGH10® unit with ng accessories and wiring
• Black double DIN fascia plate (with accessories)
• Vehicle retenon interface with plug-and-play harness
• Vehicle specic antenna adapter (AM/FM)
• Snger stereo patch lead
• Instrucon manual

3
www.sngerelectronics-eu.com
FITTING GUIDE
STEREO REMOVAL
1. Using a pry tool carefully remove the trim sur-
rounding the radio. This is nesessary in order to
reveal the screws securing the original radio. The
air vents are aached to the surrounding trim,
be cauous not to detach them when removing
the trim.
2. Remove the 4x T20 screws securing the radio
to the vehicle.
3. Pull the radio towards you in order to free it
from the dashboard, unplugging the connectors
on the rear of the radio.

4
www.sngerelectronics-eu.com
FITTING GUIDE
STEREO REMOVAL
Take the HEIGH10® components and begin to assemble the core components in accordance with the “Installaon
Manual” that comes with unit.
HEIGH10 ASSEMBLY
4. Once the original radio is removed, the next
steps will be to assemble the Heigh10 and con-
nect the steering wheel harness.

5
www.sngerelectronics-eu.com
FITTING GUIDE
INTERFACE SET-UP
FASCIA PLATE SET-UP
1. With the HEIGH10® unit congured correctly, aach the fascia brackets to the relevant sides of the radio module
using the screws within the kit. Place into the vehicle and roughly test t with the fascia to measure whether the
brackets need moving forwards/backwards.
2. With the brackets aligned correctly, aach the fascia to the brackets over the top of the unit using the screws that
come within in the kit.
3. Once all of the steps in ‘Stereo Installaon’ are complete, place the assembly into the dashboard and screw down
using the pre-exisng screws. Then reassemble the main fascia panel.
5. Aach the antenna adapter to the vehicles pre-exisng connecon and the back of new HEIGH10® unit.
2. Take the 14-way connector on the vehicle interface harness and plug this into the relevant connecon on the side
of the interface.
3. Take the 12-way connector of the stereo patch lead and plug this into the relevant connecon on the side of the
interface. Then take the 3.5mm jack and aach this to the HEIGH10® unit.
4. Aach the 4-way camera extension harness to the interface.
6. Aach the USB retenon lead in between the vehicle pre-exisng USB connector and the HEIGH10® unit.
7. Connect the male yellow RCA to the ‘reverse camera input’ on the back of the new stereo.
1. Take the interface and set the dipswitches accordingly (note that these are default to o):
ON (DOWN) OFF (UP)
DIPSWITCH 1 Pioneer head units All other head units (Default)
DIPSWITCH 2 Reverse Camera PAL Reverse Camera NTSC (Default)
DIPSWITCH 3 Reset factory sengs (switch) Reset factory sengs (Default)
DIPSWITCH 4 Not Used Not Used
9. Aach the addional wiring on the harness to the back of the stereo:
Pink - Speed Pulse Green - Park Brake Purple - Reverse
10. When all the above wires (and any addional accessories) have been connected, nally make the power connec-
ons between the stereo and the vehicles pre-exisng connector.
For a full connecon breakdown of the HEIGH10® unit, see the “Installaon Manual” that comes with the unit.
8. Connect the aermarket reverse camera (if required) to the female yellow RCA on the camera extension harness.
Note: ensure the ‘Camera Connected’ opon in the ‘Preferences’ menu is set to ‘Yes’ for the camera to funcon cor-
rectly.

6
www.sngerelectronics-eu.com
ABOUT THIS PRODUCT
CTSVW015.2
CAN-Bus Steering Wheel Control Interface for Volkswagen vehicles with MIB-PQ system and
Quadlock 52 Way connector.
NB: If vehicle is tted with an OEM Bluetooth kit, please disconnect the fuse for the Bluetooth from
the fuse board
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of
installation must be free of moisture and away from heat sources. Please ensure that the correct tools are using
during the installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for
the installation of this product.
WIRING COLOUR CODES
Purple Right Rear Speaker +
Purple/Black Right Rear Speaker -
Green Left Rear Speaker +
Green/Black Left Rear Speaker -
Grey Right Front Speaker +
Grey/Black Right Front Speaker -
White Left Front Speaker +
White/Black Left Front Speaker -
Yellow Permanent 12V
Black Ground
Red Ignition 12V
Green Park Brake
Purple/White Reverse Gear
PRIOR TO INSTALLATION

7
www.sngerelectronics-eu.com
FITTING GUIDE
1. Remove and disconnect the original head unit.
2. Connect the 12 way molex connector of the head unit patch lead (supplied
separately) to the interface.
3. Connect the opposite end of head unit patch lead to the head unit steering
wheel control input on the back of the aftermarket head unit.
NB: This may be a 3.5mm jack plug or a wire input depending upon the head unit brand be-
ing tted. Please see the head unit installation manual for further information on
where to connect.
Important: This step must be completed before connecting power to the interface. Failure to
so do may result in no steering wheel control function.
4. Connect the 14 way molex connector to the interface
5. Connect the male power/speaker ISO harness to the female power/speaker ISO harness
from the aftermarket head unit. For aftermarket head units without an ISO
connector, please refer to “Wiring Colour Codes” on Pg. 2.

8
www.sngerelectronics-eu.com
FITTING GUIDE
STEERING WHEEL CONTROL FUNCTIONALITY
6. Connect the female vehicle specic connectors on the harness to the male vehicle con-
nector from the vehicle. Test head unit for correct operation.
Function
Volume +
Volume -
Track +
Track -
Pick Up (Short Press)
Hang Up (Long Press)
Original Button
Volume +
Volume -
Right Arrow
Left Arrow
Phone Button
Phone Button

9
www.sngerelectronics-eu.com
For further help or assistance, please contact and ll out a support cket with full details of your issue via : uktechni-
[email protected]
For general enquires, contact us at:
Phone: [phone]
E-Mail: snger[email protected]
Mon - Fri 9am - 5.30pm GMT
TECHNICAL ASSISTANCE
If you would like to download a digital copy of this manual, or any other product, then please visit the www.Snger-
Electronics-EU.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest manuals & updates,
refer to our website.
Copyright 2023 by Snger.
AGREEMENT: End user agrees to use this product in compliance with the instrucons and terms of use and with all laws.
STINGER provides instrucons and safety warnings with respect to this product and disclaims all liability for any use not in
conjuncon with those instrucons or other misuse of its product. If you do not agree, please disconnue use and contact
STINGER. This product is intended for o-road use and passenger use only.