Storage Canopy W33 x L40 x H12 ft User manual

SHELTER
ASSEMBLY MANUAL
Model # W33 x L40 x H12 ft

SPECIFICATION
Width: 33 Length: 40 Height: 12
IMPORTANT ----READ MANUAL FIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and cause unnecessary and costly
mistake. If you have any questions contact your local dealer.
For User Friendly assembly we have identified each individual component with the part code as indicated in the
parts list. Please refer to the part code numbers and drawing to ensure problem free assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten once or
twice again after a few months of use. This is important when assembly in cold weather (autumn and winter)
because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric
“slack” again and need to be re-tighten before next winter.
It’s the owners responsibility to take of snow immediately if not slide off by itself.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in
high winds, or wet location.
2. Keep children away. All children should be kept away from the work area.
3. Don’t over reach. Keep proper footing and balance at all times.
4. Donot assemble in under theinfluence of alcohol or drugs. Readwarning labels on prescriptions to determine
if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do notassemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur.
Remove the cover during hurricane.
6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose toopen
flame.
7. Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips and tubes
when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous
fumes.

Parts List
Part Code
Description
Qty
L1
Base Plate
7
R1
Diagonal Base Plate for two corners
7
1
Top bent tube
7
2
Middle bent tube
14
3
Sidewall bent tube
14
4
Connection purlin
30
5
Support tube
8
6
Clip
16
7
Lower tensioning tube for roof cover
2groups
8
Roof cover
1
9
Bolt M8x70
84
10
Bolt M10x80
35
11
Ropes
1dozen
12
∮32 Plastic Plug for end of tensioning tube
4
13
Ratchet strap (for tie down ratchet)
14
14
Angle seat
4
15
Ratchet
14

EQUIPEMNT AND TOOLS FOR INSTALIATION
1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A—BASE INSTALLATION
Please refer to the diagram (Figure 1) to place the base plates.
Figure 1
1. The measurement is from center to center of the tubes. Referring to the above diagram and
confirm the place of the base plates. ENSURE THAT THE FOUNDATIONS ISSQUARE.
2. All the base plates should be welded on the Containers.

B—FRAME INSTALLATION
Please refer to the diagram (Figure 1) to install the Frame.
Figure 2
1.As Figure 2 shown find Top bent tube (part code 1), Middle bent tube (part code2) and Sidewall
bent tubes (part code3). To connect thembyScrew M8x70（part code 9）, which makes one group
of arches. Please NOTE the direction of the screw. DO NOT install the screws on the top of the
truss where the fabric will rest.
2.Life an assembled arch into one base plate and force the other end of the arch into the opposite
base plate.
3.When finishing installing the first two arches, connect the Connection purlins onto them byusing
screw M10x80（part code 10）.There are 5 pieces of Connection purlins (part code 4) between
two groups. Then install the third arch into base plate and connect the purlins. Finally install the
Support tube (part code 5) using Screw M8x70（part code9）and Clip (part code 6). By turns the
assembly for the frame is finished.

C- INSTRUCTION FOR COVER ATTACHED
Install the Roof Cover
NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A slight
breeze is the most advantageous for cover installation. To take advantage of the breeze, pull the
cover up over the arches with the breeze blowing in the cover like a sail filled with air.
1. Put the Roof cover (part code 8) EVENLY, CARRFULLR AND SLOWLY on the frame. Adjust the cover
so that it is square and evenly centered on the frame.
2. Using Ropes (part code 11) to knit the cover on the two side arches, finally tie the Roof cover to the Angle
seats (part code 14).
3. Cut 6 pockets according to the position of the base plates and put the Lower tensioning tubes for roof cover
(part code 7) into the pocket of roof cover. Then use the Ratchet straps (part code13) to tie down the Lower
tensioning tubes like the Figure 3. Finally install the∮32 Plastic plug (part code 12)for all the ends of steel
tubes.
Figure 3

NOTE:
DO NOT LEAVE THE ROOF COVER UNATTACHED UNDERANY
CIRCUMSTANCES until the final assembly and tightening has been
completed.The process is quite easy. But some tightening adjustments will be
necessary to produce a flat, tensioned roof cover. Please adjust the roof cover
every month.
Any question please contact the agent n in you city firstly.