Storage Canopy C2620 User manual

2
SHELTER
ASSEMBLY MANUAL
Model # C2620 Back wall & Frame
C2260 Back wall & frame

3
Part Number
Description
Number
1
Base plates for winch door
2
2
Base plates for door side
2
3L
Lower standing leg at left
1
3R
Lower standing leg at right
1
4L
Lower door frame at left
1
4R
Lower door frame at right
1
5L
Upper door frame at left
1
5R
Upper door frame at right
1
6
Door beam
1 Group
6A
Door boom
1
7
Horizontal tube for front door
2
7A
Horizontal tube for front door shoulder
2
8
Square tube for winch door
1
9
Mechanical wheel with wire rope
1
10
Bottom tension tube for front door
2
11
Door tube
7 Groups
12
Clips φ60
4
12A
Φ60 Half arc burning iron
4
12B
2 holes angle iron
1
13
Stake peg
8
14
Door splint
8

4
15
Soldering iron for door leg
2
16
Bolts M10*90
45
17
Carriage Bolts M8*80
8
18
Carriage Bolts M10*90
4
19
Bolts M10*30
4
20
Plastic Plug
4
21
Rope for pull door
1
22
Front cover
1
23
Added legs
2
24
Added door frame
2

5
SPECIFICATION
Length: 20 ft Width: 26 ft Height: 10ft
IMPORTANT -----READ MANUAL FIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and cause
unnecessary and costly mistake. If you have any questions contact your local dealer.
For User Friendly assembly we have identified each individual component with the part code
as indicated in the parts list. Please refer to the part code numbers and drawing to ensure
problem free assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-
tighten once or twice again after a few months of use. This is important when assembly in cold
weather (autumn and winter) because the fabric is stiff then and when we got the sun and
warm weather afterwards it will make the fabric “slack” again and need to be re-tighten
before next winter.
It’s the owners responsibility to take of snow immediately if not slide off by itself.
READ ALL INSTRUCTIONS BEFOREASSEMBLY
1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in
slippery places, in high winds, or wet location.
2. Keep children away. All children should be kept away from the work area.
3. Don’t over reach. Keep proper footing and balance at all times.
4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If
there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are
likely to occur. Remove the cover during hurricane.
6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do
not expose to open flame.
7. Be aware of personal safety during assembly and use. Be carful not to pinch fingers with
clips and tubes when assembling: when using makes sure there is adequate ventilation for
exhaust and other dangerous fumes.

6
EQUIPEMNT AND TOOLS FOR INSTALIATION
1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A--FRAME INSTALLATION
Please refer to the diagram (Figure 1) to install the base plate. UNIT: mm
Figure 1
There are four base plate comes with the back endwall. Each of them should be placed in the
right position(especially the two base plate close to the containers.)

7
Figure 2
C--INSTRUCTION FOR COVER ATTACHED
Assembly the end cover first.
NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A
slight breeze is the most advantageous for cover installation. To take advantage of the breeze,
pull the cover up over the arches with the breeze blowing in the cover like a sail filled with air.

8
Figure 3
The process is quite easy. But some tightening adjustments will be necessary to produce a flat. Please adjust
the cover timely.