Storage Canopy 40x60x15 ST Container shelter User manual

1
SHELTER ASSEMBLY
MANUAL
40x60x15 ST Container shelter
Single truss

2
PARTS LIST
Part Code
Description
Qty
L1
Left base plate
10
R1
Rigth base plate
10
1
Roof bent tube
10
2
Upside bent tube
20
3
Underside bent tube
20
4
Lower bent tube
20
5
Purlin
63
6
Inclined support tube
16
7
Clip for inclined support tube
32
8
Bolts M12x100
70
9
Bolts M10x90
160
10
Ratchet
20
11
Nylon band for ratchet
20
12
Angle seats
4
13
Roof cover
1
14
Knitting rope for cover
60
15
∮32 Plastic plug for end of tensioning tube
4
16
Tensioning tube
2 groups
17
Iron angle for base plate
20
18
Bolt 12x30
60

3
SPECIFICATIONS
Width: 40 ft
Length: 60 ft
Height: 15 ft
IMPORTANT: READ MANUAL FIRST
Improper site preparation, assembly and maintenance may invalidate warranty and cause
unnecessary and costly mistakes. If you have any questions, contact your local dealer.
For an easy assembly process, we have identified each individual component with the part
code as indicated in the parts list. Please refer to the part code numbers and drawing to
ensure problem-free assembly.
It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re-
tighten once or twice again after a few months of use. This is important when assembled
during cold seasons (autumn and winter) because the fabric gets stiff in these weather
conditions. When the weather conditions become warmer, the fabric loosens and needs
to be re-tighten
It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on
its own.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set
up near snow drifts, in slippery places, in high winds, or wet locations.
2. All children should be kept away from the work area.
3. Don’t overreach. Always keep proper footing and balance.
4. Do not assemble under the influence of alcohol or drugs. Read warning labels on
medication prescriptions to determine if your judgment or reflexes are impaired
while taking them. If there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these
conditions are likely to occur. Remove the cover during hurricanes.
6. Be careful with power and heat sources. Do not keep heat sources near the
tarpaulin. Do not expose to open flame.
7. Be aware of personal safety during assembly and use. Be careful not to pinch your
fingers with clips and tubes when assembling: When using, make sure there is
adequate ventilation for any dangerous fumes.

4
EQUIPMENT AND TOOLS FOR INSTALLATION
1. Measuring tape
2. Alignment string
3. Step ladder
4. Welder
5. Sledgehammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A - BASE PLATES INSTALLATION
Please refer to the Figure 1 to place the base plates.
Figure 1
1. The measure must be taken from center to center of the base plates. Refer to the
diagram above and confirm the place of the base plates. ENSURE THAT THE
FOUNDATIONS ARE SQUARE.
2. All the base plates need to be welded on the Containers.

5
B - FRAME INSTALLATION (Refer to figure 2 for the entire diagram)
Figure 2
1. Connect the Roof Bent Tube (part code 1), the Upside Bent Tube (part code 2), the
Underside Bent Tube (part code 3) and the Lower Bent Tube (part code 4) with the
Bolts M10x90 (part code 9); these make one group of arches. Please NOTE the
direction of the bolt. DO NOT install the bolts on the top of the truss where the
fabric will rest.
Figure 3

6
2. Insert one end of the assembled arch into one base plate and insert the other end
of the arch into the opposite base plate, then secure them using the bolts.
Figure 4
3. After installing the first two arches, connect the Purlin (part code 5) onto them
using the Bolts M12x100 (part code 8). There are 7 pieces of Connection purlins
(part code 5) between each arch.
Figure 5

7
4. Install the Inclined Support tube (part code 6) using Clip for Inclined Support Tube
(part code 7).
5. Then install the third arch into the base plate and connect the purlins.
6. Assemble the arches one by one until the frame is finished.

8
C - ROOF COVER INSTALLATION
NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A
slight breeze is the most advantageous for cover installation. To take advantage of the
breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail
filled with air.
1. Insert the Tensioning tube (part code 16) into the pockets on the end of the roof
cover (part code 13). Then put the ∮ 32 Plastic plug for end of tensioning tube (part
code 15).
Figure 6
2. Put the Roof cover (part code 13) EVENLY, CAREFULLY AND SLOWLY atop the
frame. Adjust the cover so that it is square and evenly centered on the frame.
Figure 7

9
3. On the Roof cover, cut pockets over each ratchet on the base plates, then use the
Nylon band for ratchet (part code 11) to tie down the Tensioning tubes.
Figure 8
4. Weld the Angle seats (part code 12) on each container and use Knitting rope for
cover (part code 14) to knit the cover on the two side arches and tie the Roof cover
to the Angle seats.
Figure 9

10
Please, check the detailed installation pictures below:
NOTES:
-DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANYCIRCUMSTANCES until
the final assembly and tightening has been completed.
-The process is quite easy, but some tightening adjustments will be necessary to get
a flat, tensioned roof cover. Please adjust the roof cover every month.
-Wrap tape around the gap between the steel after installing.