Sunbeam HPM5000 User manual

Heating Pads
User Guide
HPM5000, HPM5100, HPN5300

If you have any concerns regarding the performance and use of your appliance, please visit
www.sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety
precautions are understood.
Sunbeam’s Safety Precautions 3
Get to know your Heat Pad 5
Using your heat pad 6
Care and cleaning 7
Storing the heat pad 8
Troubleshooting 8
Warranty Information 9
3
Sunbeam is very safety conscious when designing
and manufacturing consumer products, but it is
essential that the product user also exercise care
when using an electrical appliance. Listed below are
precautions which are essential for the safe use of
an electrical appliance:
•Read carefully and save all the instructions
provided with an appliance.
•Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
•Turn the power off and remove the plug when
the appliance is not in use and before cleaning.
•Do not use your appliance with an extension
cord unless this cord has been checked and
tested by a qualified technician or service
person.
•Always use your appliance from a power outlet of
the voltage (A.C. only) marked on the appliance.
•Close supervision is necessary when your
appliance is being used by children or infirm
persons.
•Young children should be supervised to ensure
that they do not play with the appliance.
•Never leave an appliance unattended while in
use.
•Do not use an appliance for any purpose other
than its intended use.
•Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven. Do
not place on top of any other appliance.
•Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
•Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage
is suspected, return the appliance to the
nearest Sunbeam Appointed Service Centre for
examination, repair or adjustment.
•For additional protection, Sunbeam recommend
the use of a residual current device (RCD)
with a tripping current not exceeding 30mA in
the electrical circuit supplying power to your
appliances.
•Do not immerse the appliance in water or any
other liquid unless recommended.
•Appliances are not intended to be operated by
means of an external timer or separate remote
control system.
Contents Sunbeam’s Safety Precautions
Important instructions - retain for
future use.

If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
•Do not switch the heat pad on if moist or
wet.
•Do not use pins, needles, safety pins or other
sharp items on your heat pad.
•Examine periodically for signs of wear or
damage on the heat pad cords. If there
are such signs, or the heat pad has been
misused, return it to an authorised service
agent for inspection.
•Only use your heat pad with the controls
supplied or marked equivalent.
•Not to be used by very young children (0-3
years), infirm persons, or persons insensitive
to heat.
•Children under the age of three are not to
use this appliance due their inability to react
to overheating.
•The appliance is not to be used by young
children over the age of three unless the
controls have been pre-set by a parent or
guardian, or unless the child has been
adequately instructed on how to operate the
controls safely.
•Ensure that the heat pad is switched off and
unplugged after use.
•Do not use on varicose veins.
•Do not use if you have skin disorders or open
wounds.
•Do not use on sensitive skin or areas
insensitive to heat.
•If you are pregnant or suffer from diabetes
consult your health care practitioner before
using.
•Do not use if you have tuberculosis, tumours,
phlebitis, haemorrhages or thrombosis.
•Do not use if you have a pace maker fitted.
•Do not use outdoors.
•Do not use when intending to sleep.
•Keep out of the reach of children.
•This heat pad is not intended for use in
hospitals.
•If appliance is used on an adjustable bed,
check that the heat pad and cord do not
become trapped or rucked, for example in
hinges.
•When storing the appliance allow it to cool
down before folding.
•Do not crease the appliance by placing items
on top of it during storage.
•Should your appliance suffer a thermal or
fuse link rupture (normally identified when
the heat pad stops heating) please return
it to the manufacturer or agent for repair or
replacement.
•This appliance must not be used by
persons insensitive to heat and other very
vulnerable persons who are unable to react to
overheating.
•Do not use if folded or crumpled.
•Use only with the cover supplied.
•Do not use the heat pad to heat animals.
Attention
Instruction Booklet - Please read the instructions thoroughly before use
HPM5000 HPM5100 HPN5300
Temperature
Setting Button
Power Button
Controller
Standby Indicator
1. Low - Up to 30 degrees
2. Mild - 31 to 33 degrees
3. Medium - 34 to 36 degrees
4. High - 37 to 39 degrees
5. Rapid heat up only
Safety Precautions for your Heat Pad Get to know your heating pad
Care Label Symbols
54
Important instructions - retain for
future use.

•Remove all packaging
•Ensure the power button on the controller is
in the off position (not pressed in)
•Connect the controller to the heat pad
•Insert the plug into the power outlet and
switch on
•The heat pad will automatically default to
setting 5 for rapid heating, and begin to
heat up.
•Setting 5 is for heat up only. Do not use this
setting for continuous or overnight use.
•Place the heat pad behind your back or neck
whilst sitting or lying on a couch, chair or
bed. This versatile heat pad is
•a cozy and comfortable addition to any
lounge or bedroom.
•You can use the sleeve to secure the heat
pad to a chair back or around your arm or
leg.
•To reduce the warmth, switch to a lower heat
setting. For any continuous or overnight use,
select from settings 1-4 only.
Note: If the blue standby indicator light
on the controller begins to flash, turn the
controller off and check that the controller
is properly connected to the heat pad. If the
blue standby indicator continues to flash after
turning the controller back on, contact your
local Sunbeam Service Agent.
•The heat pad features an auto shut off. After
3 hours operation, the blue standby indicator
light will show to indicate the heat pad has
switched itself off.
This Feel Perfect heat pad features waterproof
heating elements, making them fully immersible
and safe to wash by hand or machine. Before
cleaning your heat pad, ensure that the controls
are unplugged from the heat pad.
Spot cleaning
Sponge the affected area using a neutral
wool detergent or mild soap flakes mixed with
lukewarm water. Sponge twice with clean water
to remove detergent. Remove excess water by
compressing the wet area between two towels.
Hand washing
Wash the heat pad in lukewarm water with a
neutral wool detergent or mild soap flakes. Soak
for five minutes, then gently squeeze the soapy
water through the fabric. Rinse thoroughly in
clean, lukewarm water then drain excess water
from the heat pad. Do not wring.
Machine washing
Take your heat pad to a commercial laundry or
wash in a domestic washing machine. Wash on
WOOL or DELICATES cycle with a neutral wool
detergent or mild soap flakes, below 40°C. Do
not use high speed or extra spin cycles.
Line drying
Drape the heat pad across several lines of your
clothesline. Do not use pegs on the wired areas.
Do not dry with a hairdryer or heater. Ensure
that the heat pad and control sockets are
completely dry before using again.
Machine drying
Tumble dry your heat pad on LOW setting for 15
minutes MAXIMUM. Smooth the heat pad by
gently pulling any creases out of the fabric. Line
dry to ensure the heat pad and control sockets
are completely dry before use. Do not dry with a
hairdryer or heater.
Storing your heat pad
Roll or fold your heat pad loosely and store in a
blanket bag or the bag it was supplied in. Avoid
pressing sharp creases into the heat pad. Do not
place heavy items on top of your heat pad when
storing.
Checking your heat pad
Examine the heat pad frequently for signs of
wear or damage. If there are any such signs or
if the heat pad has been misused, return it to
your nearest Sunbeam Service Agent prior to
any further use.
Using your Heat Pad Auto off function
Care and Cleaning
Using your Heat Pad
76

Store this appliance as follows when not used:
•Wait for the heating pad to be completely dry if previously washed.
•It is recommended to place the heating pad in the package provided upon purchase for better
storage.
•When storing the appliance, allow it to cool down before folding.
•Store the heating pad in a dry place.
Examine the appliance and its supply cord frequently for signs of wear or damage. lf there are such
signs or in the case of malfunction, contact an authorised technical service centre.
This chapter describes the most common problems that can arise using the appliance. If the
problems cannot be solved with the information below, please contact the Authorised Assistance
Centre.
Problem Solution
The LEDs on the control unit do not light up. Check that the control unit plug is fully inserted
in the socket. If the LEDs remain off, remove
the control unit plug from the socket and return
the underblanket to an authorised technical
service centre.
The blue warning light is flashing. Turn the control unit off and remove the plug
from the socket. Check that the control unit
connector (6) is fully inserted in the heating
pad connector (5) and reinsert the plug in the
socket. If the standby LED continues to flash,
return the heating pad to an authorised
technical service centre.
Temperature LED 1 (1) is flashing.
Return the heating pad to an authorised
technical service centre to be checked.
The product has been used incorrectly or is
damaged.
The power cable or another internal wire is
damaged.
The control unit is damaged.
There are holes or tears in the fabric or stub-
born creases that do not spread out.
3.8L
SLOW COOKER
User Guide
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia |visit www.sunbeam.com.au
phone [phone]
mail Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand |visit www.sunbeam.co.nz
phone [phone]
mail Level 6, Building 5,
Central Park,
660–670 Great South Road,
Greenlane, Auckland.
Sunbeam Corporation Limited | ABN 45 000 006 771
Sunbeam Corporation is a division of GUD Holdings Limited.
Sunbeam is a registered trademark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2015.
08/15
HP4000K
Australia
www.sunbeam.com.au
1300 881 861
New Zealand
www.sunbeam.co.nz
0800 786 232
Year
2 year
2 years
CAPRI GLASS
KETTLE
User Guide
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia |visit www.sunbeam.com.au
phone [phone]
New Zealand |visit www.sunbeam.co.nz
phone [phone]
Newell Australia Pty Ltd. ABN 68 075 071 233
Sunbeam is a registered trade mark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2021.
GCDS-SUN-SL
HPM5000_HPM5100_HPN5300_21EM1 (ANZ)
P.N: NWL0001354562
SAP 2166995
SAP 2166996
SAP 2167009
Australia
www.sunbeam.com.au
1300 881 861
New Zealand
www.sunbeam.co.nz
0800 786 232
KE6150
Storing The Heating Pad
Troubleshooting
98

CAPRI GLASS
KETTLE
User Guide
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia | visit www.sunbeam.com.au
phone [phone]
New Zealand | visit www.sunbeam.co.nz
phone [phone]
Newell Australia Pty Ltd. ABN 68 075 071 233
Sunbeam is a registered trade mark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2021.
GCDS-SUN-SL
HPM5000_HPM5100_HPN5300_21EM1 (ANZ)
P.N: NWL0001354562
SAP 2166995
SAP 2166996
SAP 2167009
Australia
www.sunbeam.com.au
1300 881 861
New Zealand
www.sunbeam.co.nz
0800 786 232
KE6150