Sunbeam HPM5000 User manual

Heating Pads
User Guide
HPM5000 HPM5200
HPM5100 HPB5400
HPN5300 HPN5500

Sunbeam’s Safety Precautions 1
Get to know your Heating Pad 4
Using your Heating Pad 6
Care and Cleaning 7
Storage 8
Troubleshooting 8
Warranty Information 9
Contents
Important instructions - retain for
future use.

If you have any concerns regarding the performance and use of your appliance, please visit
www.sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety
precautions are understood.
Sunbeam is very safety conscious when designing
and manufacturing consumer products, but it is
essential that the product user also exercise care
when using an electrical appliance. Listed below
are precautions which are essential for the safe
use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and before
cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked and
tested by a qualified technician or service
person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked on the
appliance.
• Close supervision is necessary when your
appliance is being used by children or infirm
persons.
• Young children should be supervised to
ensure that they do not play with the
appliance.
• Never leave an appliance unattended while
in use.
• Do not use an appliance for any purpose other
than its intended use.
• Do not place an appliance on or near a hot
gas flame, electric element or on a heated
oven. Do not place on top of any other
appliance.
• Do not let the power cord of an appliance
hang over the edge of a table or bench top or
touch any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre for
examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water or any
other liquid unless recommended.
• Appliances are not intended to be operated by
means of an external timer or separate remote
control system.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
Sunbeam’s Safety Precautions
1

When operating the appliance over a prolonged period of time DO NOT exceed
the temperature levels stated for continuous usage.
If the appliance is set and used at a temperature higher than those indicated for
continuous usage over an extended period of time, the user may suffer from skin
burns or heat-related injuries.
• Do not switch the heating pad on if moist
or wet.
• Do not use pins, needles, safety pins or other
sharp items on your heating pad.
• Examine regularly for signs of wear or
damage on the heating pad or on the cord
and controller. If there are such signs, or
the heating pad has been misused, contact
Sunbeam customer service line.
• Only use your heating pad with the controller
supplied or marked equivalent.
• Not to be used by very young children (0-3
years), infirm persons, or persons insensitive
to heat.
• Children under the age of three are not to
use this appliance due their inability to react
to overheating.
• The appliance is not to be used by young
children over the age of three unless the
controls have been pre-set by a parent or
guardian, or unless the child has been
adequately instructed on how to operate the
controls safely.
• Ensure that the heating pad is switched off
and unplugged after use.
• Do not use on varicose veins.
• Do not use if you have skin disorders or open
wounds.
• Do not use on sensitive skin or areas
insensitive to heat.
• The use of creams or ointments combined
with the heat of the appliance may increase
the risk of skin burns.
• If you are pregnant or suffer from diabetes
consult your health care practitioner before
using.
• Do not use if you have tuberculosis, tumours,
phlebitis, haemorrhages or thrombosis.
• Do not use if you have a pace maker fitted.
• Do not use outdoors.
• Do not use when intending to sleep.
• Keep out of the reach of children.
• This heating pad is not intended for use in
hospitals.
• If appliance is used on an adjustable bed,
check that the heating pad and cord do not
become trapped or rucked, for example in
hinges.
• When storing the appliance allow it to cool
down before folding.
• Do not crease the appliance by placing items
on top of it during storage.
• Should your appliance suffer a thermal or
fuse link rupture (normally identified when
the heating pad stops heating) please return
it to the manufacturer or agent for repair or
replacement.
• This appliance must not be used by
persons insensitive to heat and other very
vulnerable persons who are unable to react to
overheating.
• Do not use if folded or crumpled.
• Use only with the cover supplied.
• Do not use the heating pad to heat animals.
Safety Precautions for your Heating Pad
2

If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
Attention
Instruction Booklet - Please read the instructions thoroughly before use
Care Label Symbols
3
Important instructions - retain for
future use.

4
Temperature
Setting Button
Power Button Standby Indicator
Heat Setting 1-5
Setting 1-4 are for prolonged
use; Setting 5 is for rapid
heat up only
Controller R67A3
NOTE: for HPM5000, HPM5100, HPN5300, HPM5200 and HPB5400, use ONLY with Controller R67A3.
HPM5000
HPM5200
HPM5100
HPB5400
HPN5300
Get to know your Heating Pad
(HPM5000, HPM5100, HPN5300, HPM5200 and HPB5400 ONLY)

5
Temperature
Setting Button
Power Button
Standby Indicator
Heat Setting 1-4
Setting 1-3 are for prolonged
use; Setting 4 is for rapid
heat up only
Controller R90B1
HPN5500
Get to know your Heating Pad (HPN5500 ONLY)
NOTE: for HPN5500, use ONLY with Controller R90B1.

Using your Heating Pad
• Remove all packaging.
• Ensure the power button on the controller is
in the off position.
• Connect the controller to the heating pad by
inserting into the socket.
• Insert the plug into the power outlet and
switch on.
• The heating pad will automatically default to
setting 5 (on Controller R67A3) or setting 4
(on Controller R90B1) for rapid heating, and
begin to heat up.
• Setting 5 (on Controller R67A3) or Setting
4 (on Controller R90B1) is for heat up only.
Do not use this setting for continuous or
prolonged use (or if you are likely to fall
asleep with it powered on).
• Place the heating pad (HPM5000,
HPM5100, HPM5200) on your shoulder,
arm, leg, behind your back or neck whilst
sitting or lying on a couch, chair or bed.
The versatile heating pad is a cozy and
comfortable addition to any lounge or
bedroom.
• (HPM5000 ONLY) You can use the sleeve
to secure the heating pad to a chair back or
around your arm or leg.
• To reduce the warmth, switch to a lower heat
setting. For continuous or prolonged use (or
if you are likely to fall asleep with it powered
on), select from settings 1-4 (on Controller
R67A3) or settings 1-3 (on Controller
R90B1) only.
• Use HPM5000, HPM5100, HPN5300,
HPM5200 and HPB5400 ONLY with
Controller R67A3.
• Use HPN5500 ONLY with Controller
R90B1.
Note: If the blue standby indicator light
on the controller begins to flash, turn the
controller off and check that the controller is
properly connected to the heating pad. If the
blue standby indicator continues to flash after
turning the controller back on, contact Sunbeam
customer service line.
Auto off function
• The heating pad features an auto shut off.
After 90 minutes (on Controller R90B1) or
3 hours (on Controller R67A3) operation,
the blue standby indicator light will show to
indicate the heating pad has switched itself
off.
Using your Heating Pad
6

This heating pad features waterproof heating
elements, making them fully immersible and
safe to wash by hand or machine. Before
cleaning your heating pad, ensure that the
controller is unplugged from the heating pad.
Spot cleaning
Sponge the affected area using a neutral
wool detergent or mild soap flakes mixed with
lukewarm water. Sponge twice with clean water
to remove detergent. Remove excess water by
compressing the wet area between two towels.
Hand washing
Wash the heating pad in lukewarm water with a
neutral wool detergent or mild soap flakes. Soak
for five minutes, then gently squeeze the soapy
water through the fabric. Rinse thoroughly in
clean, lukewarm water then drain excess water
from the heating pad. Do not wring.
Machine washing
Wash on WOOL or DELICATES cycle with a
neutral wool detergent or mild soap flakes,
below 40°C. Do not use high speed or extra spin
cycles.
Line drying
Drape the heating pad across several lines of
your clothesline. Do not use pegs on the wired
areas. Do not dry with a hairdryer or heater.
Ensure that the heating pad and controller
socket is completely dry before using again.
Machine drying
Tumble dry your heating pad on LOW setting
for 15 minutes MAXIMUM. Smooth the heating
pad by gently pulling any creases out of the
fabric. Line dry to ensure the heating pad and
controller socket is completely dry before use.
Do not dry with a hairdryer or heater.
Storing your heating pad
Roll or fold your heating pad loosely and store it
in a dry place. Avoid pressing sharp creases into
the heating pad. Do not place heavy items on
top of your heating pad when storing.
Checking your heating pad
Examine the heating pad frequently for signs of
wear or damage. If there are any such signs or
if the heating pad has been misused, contact
customer service line prior to any further use.
Care and Cleaning
7

Store this heating pad as follows when not in use:
• Wait for the heating pad to be completely dry if previously washed.
• When storing the heating pad, allow it to cool down before folding.
• Store the heating pad in a dry place.
Examine the heating pad and its supply cord frequently for signs of wear or damage. lf there are
such signs or in the case of malfunction, contact our customer service line.
The table below describes the most common problems that can arise using the appliance. If the
problems cannot be solved with the information below, please contact the customer service line.
Problem Solution
The LEDs on the controller do not light up. Check that the controller plug is fully inserted
in the socket. If the LEDs remain off, remove
the controller plug from the socket and
contact the customer service line.
The blue warning light is flashing. Turn the controller off and remove the plug
from the socket. Check that the controller
connector is fully inserted in the heating
pad and reinsert the plug in the socket. If
the standby LED continues to flash, contact
customer service line.
Temperature LED on the controller is
flashing.
Contact our customer service line.
The product has been used incorrectly or is
damaged.
The power cable or another internal wire is
damaged.
The controller is damaged.
There are holes or tears in the fabric or
stubborn creases that do not spread out.
Storage
Troubleshooting
8

3.8L
SLOW COOKER
User Guide
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia |visit www.sunbeam.com.au
phone [phone]
mail Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand |visit www.sunbeam.co.nz
phone [phone]
mail Level 6, Building 5,
Central Park,
660–670 Great South Road,
Greenlane, Auckland.
Sunbeam Corporation Limited | ABN 45 000 006 771
Sunbeam Corporation is a division of GUD Holdings Limited.
Sunbeam is a registered trademark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2015.
08/15
HP4000K
Australia
www.sunbeam.com.au
1300 881 861
New Zealand
www.sunbeam.co.nz
0800 786 232
Year
2 year
2 years
9

HPM5000_HPM5100_HPN5300_HPM5200_HPB5400_HPN5500_23EM1 (ANZ)_GCDS-JC
PN: NWL0001354562 Rev. B
SAP 2182217
SAP 2182215
SAP 2182216
SAP 2166995
SAP 2166996
SAP 2167009
Need help with your appliance?
Contact our customer service team or visit our
website for information and tips on getting the
most from your appliance.
Australia | visit www.sunbeam.com.au
phone [phone]
New Zealand | visit www.sunbeam.co.nz
phone [phone]
Newell Australia Pty Ltd. ABN 68 075 071 233
Sunbeam is a registered trade mark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2023.
05/23