Sunjoy L-GZ1081PCO-A User manual

1/ 10
Assembly Manual
Item#: 110101105
Vendor code: L-GZ1081PCO-A
Thank you for your purchase! We are pleased that you have chosen Sunjoy for your outdoor
furniture purchase.
Our clear, easy to follow, step by step instructions will guide you through the project from start
to finish.

2/ 10
Safety information
•Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the area of the production construction.
•This package contains small items and plastic bags that should be kept away from children.
•Keep assembly area at least 6 ft. from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
•Proper placement of your product is essential. Do not place the product underneath electrical
lines.
•Keep fingers away from places where they can be pinched or trapped.
•Some parts may contain sharp edges, wear protective gloves if necessary during assembly.
•When assembling and using this product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to equipment. Please read all instructions
before assembly and use.
•Check all screws for tightness before and during usage. Ensure that all connectors and poles
are firmly and fully secured into position. It is important to do so before use so as to avoid a
possible collapse or damage to the item, which could also result in injury.
• This product is intended for outdoor use only. Install on flat, level ground.
•Stakes are provided to secure the gazebo in grass ground. If you wish to secure the gazebo
to a wood deck or concrete surface, you will need to purchase fasteners appropriate (such as
expansion bolt) for these surfaces. These are readily available at your local hardware store or
home center.
•The gazebo’s roof and structure are not guaranteed against extreme weather conditions
(storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must be cleaned
off regularly. Any damage caused by snow accumulation is not covered by the warranty.
•Do not use the unit during an electrical storm, as there is a remote chance of getting struck by
lightening.
•Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will
occur to the structure. Remove fabric roof and secure screen & privacy panels.
•Warranty does not cover damage due to extreme weather conditions.
•Please check your state and local regulations prior to purchasing. Some jurisdictions may
require permits for, or otherwise regulate, installation and use.
•Do not grill under this gazebo.
Warning
Keep all flame and heat sources away from this tent fabric. This tent meets the
flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with
any flame source. The application of any foreign substance to the tent fabric may render the
flame-resistant properties ineffective.
Assembly Preparation
• Please read and understand this entire manual before attempting to assemble or install the
product. Keep this manual for future reference.
• Keep the original packaging to store the product.
•Before beginning assembly of product, make sure all parts are present. Do not attempt to

3/ 10
assemble the product if any parts are missing.
•This unit is heavy. Do not assemble this item alone. At least four or more people are
recommended for safe assembly.
•Tools required for assembly (NOT included): Screwdriver, a hammer, and a ladder not lower
than 2.4m (about 7.8 feet).
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-578-0101 (English, French & Spanish in US) from 8:00 AM
Eastern time to 8:00 PM Eastern time, Monday –Friday or email to [e-mail].

4/ 10
Description
Part#
Label
Qty
Image
Post
GZ1081XXA01
A
4
Long screen 1
GZ1081XXA02
B1
2
Long screen 2
GZ1081XXA03
B2
2
Short screen 1
GZ1081XXA04
C1
2
Short screen 2
GZ1081XXA05
C2
2
Decorating plate
GZ1081XXA06
D
4
Long netting bar
GZ1081XXA07
E
4
Short netting bar
GZ1081XXA08
F
4
Slanting bar
GZ1081XXA09
G1
4
Bottom tube of slanting bar
GZ1081XXA10
G2
4
Long middle bar
GZ1081XXA11
H1
2
Bottom tube of long middle
bar
GZ1081XXA12
H2
2
Short middle bar
GZ1081XXA13
I1
2
Bottom tube of short middle
bar
GZ1081XXA14
I2
2
Lower connector of slanting
bar
GZ1081XXA15
J
4
Lower connector of middle
bar
GZ1081XXA16
K
4
Big top connector
GZ1081XXA17
L
1
Slanting bar of small top
GZ1081XXA18
M
4
Hook
GZ1081XXA19
N
1
Small top connector
GZ1081XXA20
O
1
Finial
GZ1081XXA21
P
1
Parts List

5/ 10
Description
Part#
Label
Qty
Image
Post base
GZ1081XXA22
Q
4
Base cover
GZ1082XXA16
R
4
Small canopy
GZ1081XXA24
S1
1
Big canopy
GZ1081XXA25
S2
1
Hardware Pack 1
Description
Part#
Label
Qty
Image
M6x25 Bolt
SM06025C
AA
16
M6 Washer
UD06C
BB
96
M6x20 Bolt
BM06020C
CC
72
M6 Nut
LM06C
DD
8
M6 Wrench
W10D
Z
2

6/ 10
Fig.1: Lift the Base cover (R) and attach the Post base (Q) to the post by Bolt (AA) and Washer (BB).
Fig.2: Attach the Lower connector of slanting bar (J) to the top of the Post (A) by Bolt (AA) and Washer
(BB)
Fig.3: Attach the Long screen1 (B1) to the Long screen2 (B2) by Bolt (CC), washer (BB) and Nut (DD).
Attach the Short screen1 (C1) to the Short screen2 (C2) by the same way.
Fig.4-1: Attach the Long netting bar (E) and Lower connector of middle bar (K) to the Long screen (B1, B2)
by using Bolt (CC) and Washer (BB). Attach the Short netting bar (F) and the Middle bar connector (K) to
the short screen (C1, C2) by the same way.
Fig.4-2: Attach the other end of the netting bar (E, F) to the Screens by using Bolt (CC) and Washer (BB).
Fig.5: Attach the Decorating plate (D) to the joint of the screens by using the Bolt (CC) and Washer (BB).
Fig.6: Attach the long and short screen (B1、B2、C1、C1) to the Posts (A) by using Bolt(CC)
and Washer(BB)

7/ 10
Hardware Pack 2
Description
Part#
Label
Qty
Image
M6 washer
UD06C
BB
16
M6 but
LM06C
DD
8
M6X45 Bolt
BM06040C
FF
8

8/ 10
Fig.7: Insert the Slanting bar (G1) into the Bottom tube of slanting bar (G2)
Fig.8: Insert the other side of Slanting bar (G1) into the Big top connector (L)
Fig.9: Attach the Bottom tube of slanting bar (G2) to the Lower connector of slanting bar (J) by using
Bolt (FF), Washer (BB) and Nut (DD).
Fig.14：Put the Small canopy (S1) on the small top and attach four corners of the small canopy tightly
to the end of the Slanting bar of small top (M).
Fig.15：Screw the Finial (P) into the Small top connector (O)
Fig.16：Attach the assembled small top into the big top by inserting the tube of the Slanting bar of
Small top (M) into the tube of the Slanting bar (G1).
Fig.10: Insert the Long middle bar (H1) into Bottom tube of long middle bar (H2), Insert the Short middle
bear (I1) into the Bottom tube of short middle bar (I2).
Fig.11: Insert the other side of the middle bar (H1, I1) into Big top connector (L), then screw the Hook
(N) into the big top connector.
Fig.12: Attach the Bottom tube of short middle bar (H2, I2) to Lower connector of middle bar (K) by
using Bolt (FF), Washer (BB) and Nut (DD), put the Big canopy (S2) on the big top without spreading it
out.
Fig.13: Insert the small top slanting bar (M) into Small top connector (O)

9/ 10
Fig.17: Spread the Big canopy (S2), and attach the four corners of the big canopy to the end of the
Lower tube of slanting bar (G2).
Fig.18: Attach the four middle fabric bags on each side of the big canopy to the end of the Bottom
tube of long middle bar (H2) and Bottom tube of short middle bar (I2). Attach the valances together
by using the hook and loop stickers preassembled in the valance.
Fig.19: Fix the assembled gazebo to the ground by using Stakes (GG).
Hardware Pack 3
Description
Part#
Label
Qty
Image
8X180 Stake
DD08180C
GG
12

10 / 10
Important
Please do not return this product to the store. For technical assistance or replacement parts, please call
our customer service department at 1-866-578-0101 (English, French & Spanish in US) from 8:00 AM
Eastern time to 8:00 PM Eastern time, Monday –Friday or email to [e-mail].
Care & Maintenance
•Before using, clean the product completely with a soft, dry towel. When not in use, wipe free of any dirt
or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely.
•Do not use strong detergent or abrasive cleaners.
•Do not machine wash.
•Bolts can loosen over time. Be sure to check bolts occasionally, tightening as needed.
•Our iron/steel components for garden accessories and patio items are coated with rust inhibiting paint
that protects it from rusting. However, due to the nature of iron, surface oxidation (rusting) will occur once
these protective coatings are scratched. This is a natural process and is not a defect! To minimize this
condition, we recommend care when assembling & handling the product to prevent scratching the paint.
Should any scratching or damage occur, we recommend immediate touch-up with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of common cooking oil. If surface
oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping on
to deck or patio and cause damaging stains, which may be difficult to remove. This can be prevented if
measure is taken to keep the product from oxidizing.
Limited Warranty
•This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided, This item is maintained with care and used only for personal,
residential purposes.
•The item is warranted to be free from defects in material or workmanship for a period of one (1) year. If
any defect is found, please call our customer service department at 1-866-578-0101 for help. The
manufacturer will not cover transportation or delivery costs, nor compensate the individual or any outside
party for assembling or disassembling the product. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
Exclusions
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of
nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is
not covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to
the original purchaser and is non-transferable. Any replacement of warranted items will be in the original
style and color, or a similar style and color if the original is unavailable or has been discontinued. As
some states do not allow exclusions or limitations on an implied warranty, the above exclusions and
limitations may not apply. This warranty gives you specific rights, and you may also have other rights,
which vary from state to state.
Made in China
2017-04