Sunny Health & Fitness SF-E3988 User manual

MAGNETIC STANDING ELLIPTICAL
WITH HANDLEBARS
SF-E3988
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your
satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED
US: [email protected] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this equipment
correctly. It is important to read this entire manual before assembling and using the equipment. Safe
and effective use can only be achieved if the equipment is assembled, maintained, and used properly.
It is your responsibility to ensure that all users of the equipment are informed of all warnings and
precautions.
1. Before starting any exercise program, you should consult your physician to determine if you have
any medical or physical conditions that could put your health and safety at risk or prevent you from
using the equipment properly. Your physician’s advice is essential if you are taking medication
that affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular
heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If you do
experience any of these conditions, you should consult your physician before continuing with your
exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To
ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of the
equipment can only be maintained if it is regularly examined for damage and/or wear and tear.
6. Always use the equipment as indicated. If you find any defective components while assembling or
checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has
been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become
entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 220 pounds (100KG)
10.To avoid bodily injury and/or damage to the product or property, proper lifting and moving are
required.
11.Your product is intended for use in cool and dry conditions. You should avoid storage in extreme
cold, hot or damp areas as this may lead to corrosion and other related problems.
12.This equipment is designed for indoor and home use only; it is not intended for commercial use.
IMPORTANT NOTE: Please remove the plastic tab from the meter before use!

2
EXPLODED DIAGRAM
HARDWARE PACKAGE
66
66
66
1
2R
2L
3
34
5
7R
7L
6
8R
8L
9
10
11
13
14
14
15
16
16
17
17
18
18
19 20
2019
21 22 22
22
22 21
23
23
23
23
23
23
23
23
24
24
24
24
24
24
25
25
26
26
27
27
24
28
28 29
29
30
31
32
33
32 33
34
35
35
36 37 37
39
40
41 42
42
44
43 45
34
47
52 48
49
50
51
46
46
46
46
24 42
53
38
12
54
54
55
55 23
56 57
56
57
58
59
60
61
62
63
64
64
65
64
65
67
#67 S5 1PC

3
PARTS LIST
No.
Description
Spec.
Qty
No.
Description
Spec.
Qty
1
Main Frame
1
34
Screw
M5*15
2
2R
Pedal Frame (R)
1
35
Flat Washer
Φ8.2*Φ16*1.5
2
2L
Pedal Frame (L)
1
36
Sleeve
1
3
Crank
2
37
Bearing
6000
2
4
Magnetic Board
1
38
Washer
Φ10.2*Φ20*1.5
1
5
Idler Wheel Shaft
1
39
Screw
M10*20*12
1
6
Axle for Crank
1
40
Nylon Nut
M10
1
7L/R
Pedal
2
41
Spring
1
8L/R
Belt Cover
2
42
Wire Clip
3
9
Tension Control Knob
1
43
Screw
M6*12
1
10
Meter
1
44
Flat Washer
Φ6.4*Φ12*1.2
1
11
Inertial Wheel
1
45
Nut
M5
1
12
Wave Washer
Φ10.2*Φ15*0.2
1
46
Sleeve
4
13
Idler Wheel
1
47
Magnet
3
14
Slide Wheel
2
48
Bolt
M8*35*15
1
15
EVA Non-slip Pad
2
49
Inductor
1
16
End Cap
2
50
Inductor Seat
1
17
Bolt
M8*45*15
4
51
Spring
1
18
Alloy Wrap
4
52
Spindle
1
19
Flat Washer
Φ8.2*Φ25*1.5
2
53
Screw
ST3.5*15
1
20
Screw
M8*16
2
54
End Cap
2
21
Hex Bolt
M8*45*15
2
55
Transportation Wheel
2
22
Bearing
4
56
Bolt
M8*35*15
2
23
Nylon Nut
M8
11
57
End Cap
2
24
Screw
ST4.2*15
14
58
Handlebar
1
25
Flange Nut
M10
2
59
Foam Grip
2
26
End Cap
2
60
End Cap
2
27
Wave Washer
Φ17*Φ21*0.4
2
61
Upright Post
1
28
Bolt
M6*12
4
62
Triangle Knob
1
29
Nylon Nut
M6
4
63
Bushing
1
30
Belt Wheel
1
64
Screw
M8*15
3
31
Belt
J300
1
65
Arc Washer
Φ8.2*Φ16*1.5
3
32
C-clip
2
66
Washer
Φ8.1*Φ10.2*2
3
33
Bearing
6003
2
67
Allen Wrench
S5
1
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
The model number (found on cover of manual)
The product name (found on cover of manual)
The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front of
the manual)
Please contact us at [email protected] or 1- 877 - 90SUNNY (877-907-8669).

4
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-907-
8669).
STEP 1:
Remove 3 Screws (No. 64)，3Washers
(No. 66) and 3 Arc Washers (No. 65) from
Main Frame (No. 1) with Allen Wrench (No.
67).
Insert Upright Post (No. 61) into Main
Frame (No. 1) using 3 Screws (No. 64)，3
Washers (No. 66) and 3 Arc Washers (No.
65) that were removed. Tighten and secure
with Allen Wrench (No. 67).
STEP 2:
Remove Triangle Knob (No. 62) from
Upright Post (No. 61).
Insert Handlebar (No. 58) into Upright Post
(No. 61), adjust the Handlebar (No. 58) to
desired height, and tighten with Triangle
Knob (No. 62).
The assembly is complete!
64
65
64 65
1
61 64
65
1
66
66
66
66
61
62
58
61
62

5
EXERCISE COMPUTER
SPECIFICATIONS
SPEED-----------------------------------------------0.0~999.9MPH (Mile/Hour)
TIME ------------------------------------------------0:00~99:59MIN
DISTANCE------------------------------------------0.0~9999M (Mile)
CALORIES------------------------------------------0.0~9999KCAL
FUNCTION KEYS:
MODE: Press the red key repeatedly to select the desired value (Time, Speed, Distance,
Calories, Scan). Hold the key for 4 seconds to have all function values reset (total reset).
FUNCTIONS:
SPEED: Displays current speed.
TIME: Counts the total time of the exercise from start to finish.
DISTANCE: Counts the distance of the exercise from start to finish.
CALORIES: Counts the total calories burned during an exercise from start to finish.
SCAN: Displays functions automatically in the following order: TIME, CALORIES, and
DISTANCE.
NOTE:
1. Please use 1pc of BUTTON CELL LR44 1.5V battery as a power supply. If there is an abnormal
display on the meter, please replace the battery.
2. The meter will automatically power on when pedals are in motion or the MODE key is being
pressed.
3. The meter will automatically start calculating when exercise begins.
4. All functions will automatically stop calculating with a “STOP” sign on the upper left corner of the
meter when there is no movement for about 4 seconds. “STOP” sign will be off and the meter will
automatically start calculating as soon as the machine is in motion.
5. The meter will automatically shut off if there is no movement for 4 to 5 minutes.

6
ADJUSTMENTS & USAGE GUIDE
ADJUSTING THE TENSION
Adjust the tension by turning the Tension Control
Knob (No. 9) clockwise to increase the level of
resistance or turning counter-clockwise to
decrease the level of resistance.
Tension levels are set at Level 1 being the lowest
and Level 8 being the highest.
ADJUSTING THE HEIGHT OF HANDLEBAR
Turn the Triangle Knob (No. 62) counter-
clockwise and remove it from Upright Post (No.
61). Adjust the Handlebar (No. 58) to desired
position, then re-tighten the Triangle Knob (No.
62) by turning it clockwise.
IMPORTANT NOTE: Please remove the plastic
tab from the meter before use!
61 61
58
61
58 58
62 62
62
Plastic Tab

7
BATTERY REPLACEMENT
1. Remove the Meter (No. 10) from Main Frame (No. 1). Then disconnect the link wire of Inductor
(No. 49) from the Meter (No. 10).
2. Remove the plastic cap from the back of Meter (No. 10).
3. Remove the old battery and insert the new battery using your fingers. Ensure that the positive
side of the battery which is labeled with a +sign is facing upward once the battery is in place.
4. Put the plastic cap onto the battery seat.
5. Reconnect the link wire of Inductor (No. 49) to the back of Meter (No. 10).
6. Reattach Meter (No. 10) onto Main Frame (No. 1).
The replacement is complete!
LR44 PLASTIC CAP
Version 1.1
WIRE INSERTING HOLE
BATTERY SEAT
10
BATTERY
PLASTIC CAP
49
1

8