Target WINDHAM WNBENCHXBK User manual

© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
>>
windham
entryway bench
assembly instructions
style # WNBENCHXBK (black)
dpci # 249-18-0087
tcin # 14402891
style # WNBENCHXBL (teal)
dpci # 249-18-0086
tcin # 14402892
style # WNBENCHXRD (red)
dpci # 249-18-0173
tcin # 16511324
style # WNBENCHXWH (shell)
dpci # 249-18-0174
tcin # 16511323
style # WNBENCHXNV (navy)
dpci # 249-18-0175
tcin # 16511322
style # WNBENCHXGY (elephant)
dpci # 249-18-0374
tcin # 50541018

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-13
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 16
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
(H4) x 22
pan-head screw
(H5) x 2
knob
(H6) x 2
knob bolt
(H7) x 8
at-head screw
(H8) x 8
allen head bolt
(H9) x 8
lock washer
(H10) x 8
washer
(H11) x 1
allen wrench
(H12) x 2
magnetic catch

5
exploded diagram
ITEM DESCRIPTION QUANTITY
1 top panel 1
2 left side assembly 1
3 right side assembly 1
4 bottom panel 1
5 left partition 1
6 right partition 1
7 back panel 1
8 left door 1
9 right door 1
10 foot support 2
11 cushion 1

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
1. 2. 3.
4. 5.

step 1: attach magnets to left/right partitions then attach to bottom panel
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
(H4) x 4
pan-head
screw
(H12) x 2
magnetic catch
1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten screws.
7
nished edge
magnetic catch

8
step 2: attach right side assembly
(H1) x 2
wooden dowel
(H8) x 2
allen head bolt
(H9) x 2
lock washer
(H10) x 2
washer
(H11) x 1
allen wrench
2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2.2. Make sure bolts go through the pre-drilled holes properly.
2.3. Do not over tighten bolts.

step 3: attach left side assembly and foot supports
(H1) x 2
wooden dowel
(H8) x 2
allen head bolt
(H9) x 2
lock washer
(H10) x 2
washer
(H11) x 1
allen wrench
3.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
3.2. Make sure bolts go through the pre-drilled holes properly.
3.3. Do not over tighten bolts.
9
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.

step 4: attach top panel
(H1) x 8
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
(H8) x 4
allen head bolt
(H9) x 4
lock washer
(H10) x 4
washer
(H11) x 1
allen wrench
4.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
4.2. Screw-in cam bolts must be screwed down ush with panel.
4.3. Refer to page 6 for instructions on how to use the cam lock system.
4.4. Make sure bolts go through the pre-drilled holes properly.
4.5. Do not over tighten bolts.
10
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.