Target hadley FKVSCB2DWH User manual

>>
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
hadley
2 door cabinet
assembly instructions
style # FKVSCB2DWH (shell)
dpci # 249-16-8945
tcin # 51902572
style # FKVSCB2DGY (stone gray)
dpci # 249-16-8734
tcin # 51774487

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-11
how to adjust door alignment 12
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 12
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
(H4) x 1
allen wrench
(H5) x 27
pan head screw
(H6) x 2
knob bolt
(H7) x 8
at head screw
(H8) x 2
knob
(H9) x 4
metal plate
(H10) x 1
magnet
(H11) x 4
bolt
(H12) x 4
lock washer
(H13) x 1
wall anchor
(H14) x 1
wall screw
(H15) x 1
truss head screw
(H16) x 1
wall strap
(H17) x 6
washer

5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side panel 1
C right side panel 1
Dxed shelf 1
E bottom panel 1
F left door 1
G right door 1
H back panel 2

6
how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
4. 5.
1. 2. 3.

77
step 1: attach magnet to top panel
(H5) x 2
pan head
screw
(H10) x 1
magnet
1.1. Align pan head screws with pre-drilled holes to attach magnet to top panel. Do not over tighten screws.

88
step 2: attach top panel, xed shelf, and bottom panel to side panels
(H1) x 12
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
(H4) x 1
allen wrench
(H11) x 4
bolt
(H12) x 4
lock washer
(H17) x 4
washer
2.1. Carefully tap small wooden dowels into place in top panel, xed shelf, and bottom panel. Leave 1/2” of the dowels sticking out.
2.2. Align bolts with pre-drilled holes to attach bottom panel to side panels. Do not over tighten bolts.
2.3. Screw-In cam bolts must be screwed down ush in top panel, xed shelf, and bottom panel.
2.4. Refer to page 6 for instructions on how to use the cam lock system.
2.5. Do not over tighten bolts.
x 4
er

9
step 3: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H5) x 25
pan head
screw
(H9) x 4
metal plate
3.1. Make sure the pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
hole for anti-tip

1010
step 4: attach doors to cabinet
(H6) x 2
knob bolt
(H7) x 8
at head
screw
(H8) x 2
knob
4.1. Align at head screws with pre-drilled holes to attach door to cabinet. Do not over tighten screws.
4.2. Align knob bolt with pre-drilled holes to attach knob to door. Do not over tighten bolts.