Target TGT-CU8-002 User manual

assembly instructions
©
8-Cube
organizer storage
2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
style # TGT - CU8 - 002.
dpci # 002 - 11 - 0589 (WHITE)
style # TGT - CU8 - 001.
dpci # 002 - 11 - 0616 (ESPRESSO)

Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in
no time. Good luck—though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-698-4846(Target 855 - MYTGTHOME) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
4. Assembly of this furniture is easier with two people.
5. Do not use power screwdrivers. Using any power tools to assemble this furniture may potentially strip the wood and hardware.
6. Do not over tighten screws.
tools needed
Hammer Screwdriver

(H4) x 18
assembly screw
#DIRECTRA NO.5 x 38
(H3) x 18
screw cover
(H1) x 6
long dowel 6 x 60 mm.
(H2) x 12
short dowel 6 x 30 mm.
(H5) x 48
nail
(H7) x 1
L-bracket screw
#7 x1/2" F / N
(H8) x 1 wall screw
#6 x1.1/2" P / N
(H6) x 1
L-bracket
hardware

Exploded diagram
ITEM
A
ฺB
C
D
E
DESCRIPTION
back panel
vertical divider
horizontal divider
top/bottom panel
side panel
DESCRIPTION
2
2
1
6
4
B
C
B
DDD
D
D
D
A
A
E
E
E
E
Optional Assembly

safety precautions
warning
This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or
serious injury could occur.
Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse.
Serious bodily injury and/or damage to personal belongings may occur.
Do not overload unit. If any shelf, top, or bottom of unit bows or bends greater than 1/2 in., it is overloaded. The shelf, top, or bottom could
collapse and cause serious bodily injury and/or damage to personal belongings.
Do not climb or step on the unit. This is not a bench. The unit may become unstable and either tip or collapse. Serious bodily injury and/or
damage to personal belongings may occur.
Do not use this unit as a television stand. Serious bodily injury and/or damage to personal belongings may occur.
Do not mount or attach anything to the sides, rear or front of the unit as this can create a force which can cause the unit to tip. Serious bodily
injury and/or damage to personal belongings may occur.
Do not stack units in a vertical format. Stacking of units can cause an unsafe tip-over hazard which may cause serious bodily injury and/or
damage to personal belongings.
Do not hang this unit on the wall. The product structure is not designed for wall hanging. Serious bodily injury, damage to personal belongings,
and/or damage to the wall may occur.
All units must be secured individually to wall stud using L-Bracket and Wall Screw (#10 x 1-1/2 in.) provided. If wall stud is not accessible,
consult your local hardware store for appropriate mounting hardware. Failure to do so may create an unsafe tipping hazard that could lead to
serious bodily injury and/or damage to personal belongings.
We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc.

helpful hints
We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc.
Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all
the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the
same way. While assembling, take care to note in each diagram which way finished edges are facing. In general, all finished edges
will face forward and all finished sides (large area of piece) will face up when product is fully assembled and upright.
hand tighten screws
We recommend you hand-tighten screws. Use care not to overtighten if using power tools.
finished edge unfinished edge

installing L-bracket
There are several "key points" to
L-bracket installation. Please review the
drawings and comments at right as well
as the assembly steps provided.
All units must be fastened to the wall.
Always mount L-bracket to a wall-stud.
The L-bracket is intended to be installed
on the top side of the top panel.
However, if you prefer more "hidden"
hardware or are stacking, you can cut
the back panel (in center at top) and
install the L-bracket under the top panel.
Install short end against wall/wall
stud; long end against unit.
Do not install this unit flush against the wall!
This unit requires a gap of between 1/2 inch and
1 inch to install properly.
For more hidden hardware, cut back panel before
installing and secure L-bracket under top panel.
See steps 4 and 5 for detailed installation instructions.
Manufactured by: S. Kijchai Company Ltd.
Address: M. 7 , Rayong, Thailand
Manufacture Date : 09/2019
Wall
stud.
Min
1/2 in.
Max
1 in.
Wall
stud.
Short
end
long end
Wall
stud.
Top Panel
Children have died from
furniture tipover.To reduce the
risk of furniture tipover:
ALWAYS install tipover restraint
provided.
NEVER put aTV on this product.
NEVER allow children to stand, climb
or hang on drawer, doors, or shelves.
NEVER open more than one drawer
at a time.
DO NOT defeat or remove the drawer
interlock system.
Place heaviest items in the lowest drawers.
This is a permanent label. Do not remove!

Step 1. Insert dowel into vertical dividers. (D)
D
(H1) x 6
long dowel 6 x 60 mm.
(H2) x 6
short dowel 6 x 30 mm.
H1
B
D
D
D
H2
H2
H2
H2
(H4) x 3
assembly screw
#DIRECTRA NO.5 x 38
B
H1
H2
H2
DH1
H1
H2
H2
DH1
H1
H2
H2
H2
H2
1. Insert six long dowels (H1) and short dowel (H2) into vertical dividers. (D)
2. Place three vertical dividers (D) onto top/bottom shelf (B) facing short dowel (H2) side.
3. Secure each vertical divider with a screw (H4). Make sure finished edges are facing up.
H4
H4
H4
long dowel 6 x 60 mm.
shot dowel 6 x 30 mm.
long dowel 6 x 60 mm.
shot dowel 6 x 30 mm.

step 2. Place horizontal divider (C) over vertical dividers(D)
C
C
1. Place horizontal divider (C) over vertical dividers(D). The long dowel should go through all the holes on horizontal dividers (C)
BB
long dowel 6 x 60 mm.

step 3. Insert dowel into vertical dividers. (D)
D
(H2) x 6
short dowel 6 x 30 mm.
H2
H2
H2
H2
H2
H2
1. Insert six shot dowels (H2) into vertical dividers. (D)
2. Place three vertical dividers (D) onto horizontal divider (C)
DD
D
D
D
B
shot dowel 6 x 30 mm.