Target Modern Milan FRS50145ST User manual

modern milan free-standing egg chair with ottoman
style # FRS50145ST
dpci # 009000479
>>assembly instructions TM

Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
ATTENTION:
This Chair is not intended for use during any kind of inclement weather and the manufacturer is not,
and can not beheld responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Chair not being stored properly when not in use, is not the
responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Chair needs to be stored in a dry, sheltered place to
prolong the life and to avoid damage to the Chair.
2
IMPORTANT WARNING:
Unpack the box on a clean, soft, level surface and make sure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.

WARRANTY:
This Chair comes with a one year limited warranty against original manufacture defects. If you experience
trouble with your chair, please call the customer service number below.
3
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Yotrio 2020
before you begin
1. Check for damage or missing parts. Call to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
855-MYTGTHOME (855-698-4846)

table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-15
QUESTIONS?
4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware
5
(Part I)×6
M6*20 bolt with washer
(Part J)×4
M6*30 bolt with washer
(Part P)×1
hex wrench
(Part O)×1
allen wrench
(Part M)×12
M6 nut
(Part L)×12
M6*60mm bolt with washer
(Part K)×6
M6*35mm bolt with washer
(Part N)×12
Washer

ITEM DESCRIPTION QUANTITY
1
A
6
left bottom frame
B right bottom frame 1
1
Cleft top frame
A
B
C
D
E
G
G
F
H
1
Dright top frame
1
Eseat frame
1
Fottoman seat frame
2
Gside panel
1
Hconnector bar

7
step 01:
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
2. Secure with M6*60 bolt with washer (L), M6 nut (M), washer (N), tighten using hex wrench (O) and allen wrench (P).
1. Attach the left top frame (C) to the right top frame (D) with the corresponding screw holes.
Do not completely tighten screws until all screws are started.
C
D
N
L
M
(Part M)×4
M6 nut
(Part L)×4
M6*60mm bolt with washer
(Part P)×1
hex wrench
(Part O)×1
allen wrench
(Part N)×4
Washer

8
step 02:
1. Attach the left bottom frame (A) to the seat frame (E ) by lining up screw holes
Do not completely tighten screws until all screws are started.
A
E
E
K
(Part P)×1
allen wrench
(Part K)×3
M6*35mm bolt with washer
2. Secure with M6*35 bolt with washer (K), tighten using allen wrench (P).

9
step 03:
1. Attach the right bottom frame (B) to the seat frame (E ) by lining up screw holes
Do not completely tighten screws until all screws are started.
(Part P)×1
allen wrench
(Part K)×3
M6*35mm bolt with washer
2. Secure with M6*35 bolt with washer (K), tighten using allen wrench (P).
B
E
K

10
step 04:
Do not completely tighten screws until all screws are started.
(Part P)×1
allen wrench
1. 2.
(Part I)×2
M6*20 bolt with washer
A
B
E
E
I
M
N
L
(Part M)×2
M6 nut
(Part L)×2
M6*60mm bolt with washer
hex wrench
(Part O)×1
(Part N)×2
Washer
1. Secure with M6*20 bolt with washer (I) and M6*35 bolt with washer (K), tighten using allen wrench (P).
2. Secure with M6*60 bolt with washer (L), M6 nut (M), washer (N), tighten using hex wrench (O) and allen wrench (P).