Target Hadley FKVS1DCBGY User manual

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
>>
hadley
1 door cabinet
assembly instructions
style # FKVS1DCBGY (stone gray)
dpci # 249-16-7740
tcin # 53289611
style # FKVS1DCBWH (shell)
dpci # 249-16-2727
tcin # 53289610

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-10
how to adjust door alignment 11
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

hardware
(H1) x 12
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
(H4) x 4
bolt
(H5) x 4
lock washer
(H6) x 4
washer
(H7) x 10
small pan head screw
(H8) x 1
magnet catch
(H9) x 2
large pan head screw
(H10) x 1
knob
(H11) x 1
knob bolt
(H12) x 4
at head screw
(H13) x 1
allen wrench
4

exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side panel 1
C right side panel 1
D bottom panel 1
Exed shelf 1
F back panel 1
G door 1
5

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
5.4.
1. 2. 3.

step 1: attach top panel, xed shelf, and bottom panel to right side panel.
(H1) x 6
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
(H4) x 2
bolt
(H5) x 2
lock washer
(H6) x 2
washer
(H13) x 1
allen wrench
1.1 Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.
7

step 2: attach left side panel.
(H1) x 6
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
(H4) x 2
bolt
(H5) x 2
lock washer
(H6) x 2
washer
(H13) x 1
allen wrench
2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.
8

9
step 3: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H7) x 10
small pan head
screw
3.1. Make sure the screws go through the pre-drilled holes properly.
3.2. Do not over tighten screws.

10
step 4: attach door.
(H12) x 4
at head screw
(H8) x 1
magnet catch
(H9) x 2
long pan
head screw
(H11) x 1
knob bolt
(H10) x 1
knob
4.1. Align screws with pre-drilled holes.
4.2. Do not over tighten screws.
4.3. Align bolt with pre-drilled hole.
4.4. Do not over tighten bolt.
If planning to install the door, opening to
the left, use right side pre-drilled holes
for magnet.
If planning to install the door opening to
the right, use left side pre-drilled holes
for magnet.