Target room essentials 249-05-0297 User manual

>> assembly instructions
room essentials
5 Shelf Bookcase - Espresso Brown dpci 249-05-0297
5 Shelf Bookcase - White dpci 249-05-0298
5 Shelf Bookcase - Black dpci 249-05-0299
5S – TALL BOOKCASE_MFG_B_01

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
tools needed
before you begin
1. Check for damaged or missing parts. Call 1-800-440-0680 to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
QUESTIONS? Just call 855-MYTGTHOME (1-800-440-0680) for parts and service. For faster service, have the DPCI number ready when calling.

3
table of contents
introduction 2
hardware 6
parts list 7
assembly 9-24

4
WARNING
this product is intended for oor use only and not for wall mount use.
WARNING
Serious or fatal crushing injuries
can occur from furniture tip-over.
To help prevent tip-over:
• Install tip-over restraint provided.
• Place heaviest items on the
lowest surfaces as far back from
the front edge as possible.
• Do not set TVs or other heavy
objects on top of this product,
unless the product is specifically
designed to accomodate them.
• Never allow children to climb or
hang on drawers, doors, or shelves.
Use of tip-over restraints may
only reduce, but not eliminate,
the risk of the tip-over.
This is a permanent label.
Do not attempt to remove!
Serious or fatal crushing injuries can occur from furniture tip-over.
To help prevent tip over:
• Anchor unit to stud or wall
• Place heaviest items on the lowest surfaces as far back from the front edge as possible.
Do not set TVs or other heavy objects on top of this product, unless the product is speci-
cally designed to accomodate them.
• Do not allow children to climb or hang on unit.
• Use of tip-over restraints may only reduce, but not eliminate the risk of the tip over.
• This unit contains small parts which could be a choking hazard for small children. Children
should be under adult supervision at all times or serious injury could occur.
• Do not mount or attach anything to the sides, rear or front of the unit as this can create
a force which can cause the unit to tip. Serious bodily injury and/or damage to personal
belongings may occur.
• Do not stack units. Stacking of units can cause an unsafe tip-over hazard which may
cause serious bodily injury and/or damage to personal belongings.
• All units must be secured individually to wall
• DO NOT use this item if any parts are missing, damaged or worn.
• DO NOT use this item unless all xings are secured.
• Always use on a level, even surface.
This product is TSCA Title VI Compliant
This product is California 93120 Compliant For Formaldehyde Phase II
WARNING: This product can expose you to chemicals including Formaldehyde,
which is known to the State of California to cause cancer or birth defects or
other reproductive harm.
For more information go to www.P65Warnings.ca.gov/furniture.
Manufactured by Friul Intagli Industries spa, Via Oderzo 68, 33080 Villanova di Prata, Italy
Imported and distributed by Target Corporation, 1000 Nicollet Mall, Minneapolis, MN 55403, USA
Guest Services: 1-800-440-0680

5
E
F
F
F
F
Side
WARNING:This unit has been designed to support the
maximum loads shown. Exceeding these load limits could
cause sagging, instability, product collapse, and/or serious
injury.
WARNING: Please ensure that all the objects are
removed before moving the assembled unit. The unit must
be lifted by more than one person, not dragged or pushed.
Failure to do so will cause product damage, instability,
product collapse, and/or serious injury.
30lbs
30lbs
30lbs
30lbs
30lbs
30lbs
weight capacity/care instructions
E
F
F
F
F
Side
WARNING:This unit has been designed to support the
maximum loads shown. Exceeding these load limits could
cause sagging, instability, product collapse, and/or serious
injury.
WARNING: Please ensure that all the objects are
removed before moving the assembled unit. The unit must
be lifted by more than one person, not dragged or pushed.
Failure to do so will cause product damage, instability,
product collapse, and/or serious injury.
30lbs
30lbs
30lbs
30lbs
30lbs
30lbs
Cleaning Instructions:
• Gently wipe the cabinet with a soft cloth
• To clean the cabinet, dampen the cloth with a neutral detergent and water,
wipe the cabinet and follow with a dry cloth.
• DO NOT clean with benzene thinner, alkaline detergent, alcoholic system detergent,
glass cleaner, wax, polish cleaner, soap powder, or insecticide.
• Rubber or vinyl should not be in contact with the cabinet for an extended period of time.
These types of uids and materials can cause the nish to deteriorate, crack or peel.
• No lubrication required.

6
hardware
E
A
F
F
F
F
B
x 24
x 4
x 1
x 2
(H1) x 4
large cam
(H2) x 2
small cam
(H3) x 8
cam cover cap
(H5) x 2
short cam bolt
(H4) x 4
long cam bolt
(H6) x 2
knob
(H7) x 4
large wooden dowel
(H8) x 2
small wooden dowel
(H10) x 1
allen wrench
(H9) x 1
glue
(H11) x 4
L-bracket
(H12) x 2
hinge
(H13) x 16
1/2” pan-head screw
(H15) x 2
7/8” pan-head machine screw
(H14) x 8
Glue
(H16) x 4
2” hex-head screw
(H17) x 4 (H18) x 12
1-1/8” washer-head screw
(H20) x 1
touch-up stick
(H19) x 35
nail
(H21) x 2 sets
drawer glides
(H22) x 1
magnetic catch
(H23) x 1
strike plate
(H25) x 1
strike plate screw
(H24) x 2
magnetic catch screw
(H6) x 4
support foot
(H7) x 40
nails
(H8) x 1
nail guide
(H9) x 1
support foot
(H8) x 4
cam
(H9) x 4
assembly dowel
anti-tip hardware
(H1) x 12
wood dowel
(H5) x 1
nail holder
(H2) x 12
conformat screw
(H3) x 12
shelf pin
(H4) x 48
nail
(H12) x 2
washer
(H11) x 1
L Bracket 3/8” flat-head screw
(H15) x 1(H13) x 1
wall Anchor
(H14) x 1
2”3/8 screw TC
(H7) x 1
screw cover Ø20
(H6) x 1
screw cover Ø15
(H10)x 4
iron plate

7
ITEM DESCRIPTION QUANTITY
A upper side Lh 1
B upper side Rh 1
C lower side Lh 1
D lower side Rh 1
E back panel 1
F back panel 1
G top/bottom panel 2
H shelf 3
L top panel 1
(29.2 x 89.6cm) (29.2 x 89.6cm) (61.8 x 90.1cm)
(29.2 x 89.6cm) (29.2 x 89.6cm) (61.8 x 88.3cm)
(62.4 x 29.4cm)
(59 x 29cm) (58.9 x 29cm)
Bottom
(70.1 x 29cm)
Double back panel
(29 x 182.9cm)
Left side
(29 x 182.9cm)
Shelves x 4
(70.1 x 29cm)
Right side
(72.2 x 180.3cm)
Top
(75.3 x 29.2cm)
3
D C E
A3
F
3
B
Ax1Bx1
Cx1Dx1
Ex1
Fx1
Lx1
Gx2Hx3
M
A
B
D
C
E
F
G
G
H
H
L
H

8
Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all
We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc.
the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same
way. While assembling, take care to note in each diagram which way finished edges are facing. In general, all finished edges will
face forward and all finished sides (large area of piece) will face up when product is fully assembled and upright.
hand tighten screws
We recommend you hand-tighten screws. Use care not to overtighten if using power tools.
unfinished edgefinished edge
helpful hints

9
step 1.
1. Carefully tap wooden dowels (H1) into place.
WHEN FITTING CAMS
ENSURE STARTING POSITION IS CORRECT
BEFORE YOU INSERT CONNECTING CAM-PILLAR
CORRECT WRONG
C
A
D
C
A
D
180°
C
D
B
180°
C
D
G
G
(H1) x 12
wood dowel

step 2.
1. Carefully tap cam (H8) into place.
10
C
D
C
D
(H8) x 4
cam

11
step 3.
1. Attach bottom panel (G) onto side panels (C) and (D) as shown.
Ensure wooden dowels are aligned correctly with the holes of matching parts before attaching.
2. Secure bottom panel (G) onto side panels (C) and (D) using screwdriver to turn tting
conformat screw (H2) to x.
G
SEAM
SEAM
(H2) x 4
conformat screw

step 4.
G
A
B
SEAM
1. Attach top panel (G) onto side panels (A) and (B) as shown.
Ensure wooden dowels are aligned correctly with the holes of matching parts before attaching.
2. Secure top panel (G) onto side panels (A) and (B) using screwdriver to turn tting
conformat screw (H2) to x.
12
(H2) x 4
conformat screw

13
step 5.
1. Attach central panel (L) onto side panels (A) and (B) as shown.
2. Secure central panel (L) onto side panels (A) and (B) using screwdriver to turn tting
conformat screw (H2) to x.
L
A
B
SEAM
(H2) x 4
conformat screw

step 6.
1. Attach 4x assembly dowel (H9) into the pre-drilled holes on central panel (L),
screw-In cam bolts must be screwed down ush.
L
14
(H9) x 4
assembly dowel

15
step 7.
L
D
C
1. Attach central panel (L) onto side panels (C) and (D) as shown.
Ensure ssembly dowel are aligned correctly with cam of matching parts before attaching.
2. Secure central panel (L) onto side panels (C) and (D) using screwdriver to turn tting
cam to x.
L
D
C

step 8.
F
E
E
C
A
B
88.3cm 90.1cm
Unfinished
surface
F
E
F
16
1. Position back panels (E) and (F) as shown.
WARNING
TSCA Title VI Compliant
California 93120 Compliant For Formaldehyde Phase II
Manufactured by Friul Intagli Industries spa
Via Oderzo 68, 33080 Villanova di Prata, Italy
Guest Services: 1-800-440-0680
Imported and distributed by Target Corporation
1000 Nicollet Mall, Minneapolis, MN 55403, USA
Bookshelf - 3 Shelves - DPCI #249-05-0293
Serious or fatal crushing injuries
can occur from furniture tip-over.
To help prevent tip-over:
• Install tip-over restraint provided.
• Place heaviest items on the
lowest surfaces as far back from
the front edge as possible.
• Do not set TVs or other heavy
objects on top of this product,
unless the product is specifically
designed to accomodate them.
• Never allow children to climb or
hang on drawers, doors, or shelves.
Use of tip-over restraints may
only reduce, but not eliminate,
the risk of the tip-over.
This is a permanent label.
Do not attempt to remove!
WARNING: This product can expose you to chemicals including
Formaldehyde, which is known to the State of California to cause
cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/furniture.
2019/01/30

17
step 9.
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
=
=
X
X Y = J K
K
K
X
Y
Y
J
J
F
E
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
=
=
X
X Y = J K
K
K
X
Y
Y
J
J
F
E
1. Before attaching the back panels (E) and (F), checking the correct allocation.

step 10.
18
1. Attach back panels (E) and (F) onto back side of the unit using all 44x nail (H4), evenly distributed with the help
of the nail holder (H5), and 4 iron plate (H10) with 4x nail (H4),as shown.
F
E
F
E
(H5) x 1
nail holder
(H4) x 48
nail
(H10)x 4
iron plate

19
step 11.
1. With help of an assistant carefully stand up the unit
E
F
F
F
F
Side

1. Attach screw cover Ø15 (H6) over screwheads.
2. Attach screw cover Ø20 (H7) over camheads.
step 12.
20
x2
F
H7
H7
H7
H6
H6
H6
H6
H6
H6
H6
H6
H7
(H7) x 1
screw cover Ø20
(H6) x 1
screw cover Ø15