Target DSESTDSKWH User manual

anywhere desk
>> assembly instructions
style # DSESTDSKWH
dpci # 249-14-0617
tcin # 15837514
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2
Congratulations on your latest purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged parts. Call 1-877-436-7290 or e-mail [email protected] for service.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-11
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 20
wooden dowel
(H2) x 12
cam bolt
(H3) x 12
cam
(H4) x 10
long at head screw
(H5) x 1
pull
(H6) x 2
pull bolt
(H7) x 4
short at head screw
(H8) x 1
19mm pan head screw
(H9) x 1
wall strap
(H10) x 2
5/8” washer
(H11) x 1
wall anchor
(H12) x 1
38mm wall screw

exploded diagram
ITEM DESCRIPTION QUANTITY
Z
top panel
1
Y
left side frame
1
X
right side frame
1
D
front stretcher
1
E
back panel
1
W
keyboard tray
1
V
right drawer side
1
U
left drawer side
1
S
right drawer back
1
T
left drawer back
1
5

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
66
1. 2. 3.
4. 5.

step 1: attach front stretcher and back panel to side frames
(H1) x 4
wooden dowel
(H2) x 6
cam bolt
(H3) x 6
cam
1.1. Carefully tap small wooden dowels into place in left and right side frames. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in left and right side frames.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.
7

step 2: attach top panel
(H1) x 6
wooden dowel
(H2) x 6
cam bolt
(H3) x 6
cam
2.1. Screw-In cam bolts must be screwed down ush in top panel.
2.2. Carefully tap small wooden dowels into place in side frames and back panel. Leave 1/2” of the dowels sticking out.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.
8
(H2) x 6
cam bolt
(H3) x 6
cam
Screw-In cam bolts must be screwed down ush in top panel.

step 3: assemble drawer
(H1) x 10
wooden dowel
(H5) x 1
pull
(H6) x 2
pull bolt
(H4) x 10
long at head screw
3.1. Carefully tap wooden dowels into place in keyboard tray. Leave 1/2” of the dowels sticking out.
3.2. Use pull bolt to attach pull to keyboard tray.
3.3. Use at head screws to attach drawer components being careful not to overtighten.
9
(H1) x 10
wooden dowel
(H5) x 1
pull
(H6) x 2
pull bolt
(H4) x 10
long at head screw
3.1. Carefully tap wooden dowels into place in keyboard tray. Leave 1/2” of the dowels sticking out.

step 4: install drawer
(H7) x 4
short at head screw
4.1. With slides fully extended, set drawer down on the tabs of the slides.
4.2. On each side, insert one screw into the side and one screw into the bottom of the drawer.
4.3. Do not over tighten screws.
10
With slides fully extended, set drawer down on the tabs of the slides.