Technogym MH67E User manual

1 02/02/2012
-
Phillips screwdriver
-
-
-
-
-
NB
-
-
-
-
In order to anchor the machine to the ground, position the plates before closing the guards
T wrenches size 5-6-8-10
PERSONS REQUIRED FOR INSTALLATION
The weight of the machine is concentrated around the seat area
INSTALLATION MANUAL FOR
KINESIS STATIONS STEP MH67E
EQUIPMENT REQUIRED FOR INSTALLATION
Combination ratcheting wrench 17 and/or open-end wrench 17
Scissors
Electric screwdriver with Phillips head and/or Phillips screwdriver
Hand truck and/or platform trolley
The hardware is contained in an appropriate blister with the relative
The guards are extremely delicate (once unpacked they get dirty very
easily)
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

2 02/02/2012
Quantity
2
4
2
4
2
1
2
2
B - 0Z126
C - 0ZV00071
D - 0Z208
E - 0Z165
F - 0Z415
G - 0Z 306
M10x35 screw
M10x30 screw
10.5x20x2 washer
M5x10 screw
M10 self-locking
M8x16 screw
H - 0N001389 plate
M10x85 screw
Description
General information
HARDWARE
Blister letter-code
A - 0Z050
fixing time
52 50
Installation time (minutes) in std conditions
10CIC handling timeCode total persons installation time
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

3 02/02/2012
Remove the cardboard packaging box
MACHINE UNPACKING
DO NOT USE A CUTTER
MACHINE UNPACKING SEQUENCE
phase 1
Operator A Operator B
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

4 02/02/2012
Remove part of the RH-LH wooden frame (black
broken line) Extract the machine components and place them near the unpacking zone
Operator A Operator B
phase 2
Remove 2+2 screws of the RH-LH wooden
crossbeams (see detail)
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

5 02/02/2012
Operator B
phase 3
Cut the lower cable tie securing the wooden frame (do not cut the 4 upper cable ties), position the hand truck,
separate the wooden frame from the pallet and transport the machine to the area near the unpacking zone
Operator A
N
O
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

6 02/02/2012
Remove wooden frame "A" and remove the polyethylene packet
phase 4
Operator A/B
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

7 02/02/2012
Transport the machine to the assembly zone using the hand truck or platform trolley depending on the type of
zone + the components
phase 5
Operator A/B
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

8 02/02/2012
Turn the step unit by 90°(F1), turn the platform u nit by 90°and join it to the step unit (F2), tighten with 2 screws +
2 washers (F3) (REMEMBER TO PLACE A CARDBOARD PROTECTION SHEET BETWEEN THE FLOOR AND
SEAT ASSEMBLY)
phase 1
Insert the rear foot in the frame assembly, tighten with 2 screws (K) + 1 screw (J) + 2+2 washers + nut (F1), position and
tighten the piston unit plate with 2 screws (F2)
MACHINE ASSEMBLY SEQUENCE
Operator A/B
Turn the platform assembly by 90°, insert it in the frame assembly and tighten with 2+2 screws + 2+2 washers
F1 F2
F3
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

9 02/02/2012
Operator A Operator B
Feed the cables through on the RH side of the Feed the cables through on the LH side of the machine
Loosen the 4 screws (leaving them inserted) of the
pivoting unit box, remove the cover
phase 2
Remove the lower guard of the pivoting unit by
loosening the internal screw
Remove the front pivoting unit by levering on the
side hook
Repeat the same sequence of operations as operator A
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1

10 02/02/2012
Operator B
phase 3
feed the cables through (starting from the cable
coming out of the RH pulley)
Operator A
Repeat the same sequence of operations as operator A
drafted by Fabrizio Frattini
approved by Andrea Borghesi revision 1/1