Tecway Kiddie Jet User manual

Kiddie Jet

2
In order to prevent the variety of problems which caused by
incorrect operation，Please read the manual first before operating
this machine and pay attention to the items marked in “note”.
Please keep this manual carefully for checking when needed.
Summary
Transportation, installation, safe operation of moving and
operating methods and attentions;
Installation and operation;
Function adjustment;
Maintenance;
General troubleshooting and solutions;
Main components diagram;

3
Safety Attentions
1) Certain part of the game is with high voltage. Adjust the game by
technician. Do not open the game door unless maintenance or parts
replacement is required.
2) Please switch off the power before checking and maintenance.
3) Please switch off the power before opening the game door.
4) Fire extinguisher equipment must be nearby the game.
Installation
The game must be located properly to avoid damages.
Improper Locations:

4
Notes of Usage
1) The voltage range of the game should be 105V~115V or 215V~225V.
The proper voltage should be 110V/220V. The specific voltage accords
to the date plate on the back door of the game. The voltage must be
correct; otherwise it would be difficult to repair the damage.
2) The plug must be plugged in tightly and keep the power cords not be
too tight and damaged in order to prevent bodily injury, short-circuit
and power leakage.
3) To put the machine to normal operating, please properly adjust the
coin match and the game settings when use at the first time.
4) Please regularly check all the functions of the game when operate to
prevent dysfunction.
Notes of Maintenance
1) Be sure to check and maintain the game regularly.
2) Switch off the power before replacing the parts of the game.
3) The parts for replacement should be the same model as the old one.
4) Please check the connection and voltage output after replacing the
power supply.
5) The voltage range of the PCB should be 5.1V-5.4V.
6) Check whether the game has creepage and the voltage before repairing
the PCB.

5
Notes of Clean
1) Please use clean and soft cloth to clean the game.
2) Prevent damaging the surface of the game, please do not use the
following cleanser:
Alterative Cleanser；
Acidic Cleanser；
Insecticide, sterilized water, alcohol or other chemical cleanser.
Notes of Moving and Shipping
1) Properly disassemble the game for necessary moving and shipping.
2) Prevent the game from hitting or being attrite during movement.
3) Protecting the case when move the game.

6
CONTENT
1. GAME INTRODUCTION ........................................................................................ 7
2. TECHNICAL PARAMETER................................................................................... 8
3. MOVEMENT............................................................................................................. 10
4. INSTALLATION........................................................................................................11
4.1 CHOOSE THE LOCATION FOR INSTALLATION .............................. 11
4.2 CHECK AND SET BEFORE CONNECTING THE POWER ...............12
4.3 CHECK AND ADJUST AFTER CONNECTING THE POWER............13
5. CHECK BEFORE OPERATION......................................................................... 13
6. DAILY OPERATION............................................................................................... 14
6.1 INPUT POWER TO OPERATE ..........................................................14
6.2 CHECK AFTER OPERATION............................................................14
6.3 COLLECT COINS AND KEEP RECORD ...........................................14
7. GAME SETTING..................................................................................................... 15
7.1 KEYS FOR SETTING ........................................................................15
7.2 SETTING METHOD...........................................................................16
7.3 SETTING DESCRIPTION..................................................................16
8. ADJUSTMENT ........................................................................................................ 18
8.1 ADJUT THE COIN MECH ..................................................................18
8.2 MAIN BOARD ADJUSTMENT ...........................................................19
9. CHECK AND MAINTAIN...................................................................................... 20
9.1 DAILY CHECK ...................................................................................20
9.2 DAILY MAINTENANCE .....................................................................20
10. TROUBLESHOOTING.......................................................................................... 21
11. .............................. 22SCHEMATIC DIAGRAM FOR AIR CIRCUIT SYSTEM
12. SCHEMATIC DIAGRAM....................................................................................... 23

7
1. Game introduction
Playing Tips：
Ride on the Kiddie Jet and insert coin, press the start button to
to start the game. You will encounter the enemy aircraft, press the
fire button to hit them, the more aircrafts you hit the higher score
you will get.
display
seat
railing
fire button
coin entrance

8
2. TECHNICAL PARAMETER
VOLTAGE: AC 220V/110V（50/60HZ）
MAX. CURRENT：6A/12A
(Note: please refer to the nameplate located on the back of the
games to check actual usage of voltage.)
MAX. POWER: 1200W
COIN SIZE：φ21mm ~ φ30mm (diameter)
1.2mm ~ 2.5mm (thickness)
CAPACITY OF COIN BOX: 1200pcs of coins with coin size
φ25mm*1.5mm
LOCATION REQUIRED: -5 ~ 40℃, humidity is less than 90%. No
contact with any corrosive liquid, no any greasiness and dirt.
DIMENSIONS:L2080mm*W1460mm*H1330mm
1460
1300
2080

9
1
Parts shipped with the game:
1 LED Green\Red each 2
2LEDRed
、Green、Blue each 2
3 Key 1285＃2
4 Key 1396＃2
5PowerCord
6 Manual 1
OPERATION MANUAL

10
3. Movement
Direction of movement diagram：
Note: when the road surface is uneven during moving or when you
tilt the machine, please pay attention to the strength and hang the
chassis in the air to prevent damage to the air sac.
WARNING
Please power off the game first and pull out the cord, then move the game.
Please do not carefully move, turnover, transport the game; otherwise it
will destroy the game.
Prevent hitting, rubbing the games when move the games, otherwise it will
damage the appearance of the game.

11
4. INSTALLATION
Please follow the direction below to install the game.
4.1 CHOOSE THE LOCATION FOR INSTALLATION
1) Put the Kiddie Jet in the same type of Kiddie Ride with monitor then
select the concrete placement machine according to the machine's
exterior.
2) Choose the proper location for installation, please follow the below
drawing to install.
2.5m
3.1m
0.5m0.5m
0.5m 0.5m
NOTE：It must be placed on the flat floor to make the machine on the ground
steadily.

12
4.2 CHECK AND SET BEFORE CONNECTING THE POWER
1) Please check whether the parts of cabinet are loose caused by moving,
and the wire terminal should not drop out from the port.
2) Check whether the GND is connected.
3) Please check whether the resistance of power input at the both ends for
GND is more than 100 megohm.
4) Adjust the coin machine and check if it can work properly.
5) Connect the wires.
Attention
A Please make sure the power cord is not pressed by wheel, foundation,
etc. Otherwise, it will damage the wire to cause short circuit, even fire.
Do not use strong power to extend and wring the wires. Do not make
the wire be near to the high temperature object. Properly put the wire
to avoid any kicking or treading.
AAAA
B Hold the plug to pull it out from the socket. Do not touch the plug with
wet hands.

13
4.3 CHECK AND ADJUST AFTER CONNECTING THE POWER
1) Make sure the input voltage is same as the one stated on name plate
on the back door of the game.
2) After connecting the power, please switch on the game.
3) Inserting coin to check if the coin machine cans work properly.
4) Visually check the game and confirm the display and light can work
properly.
5) Enter into the setting program and set the game settings (include coin,
game time, game levels, etc.)
6) Insert coin to play the game, confirm the fire button and the machine
movement are normal.
7) Check the sound if it is ok.
5. CHECK BEFORE OPERATION
Check the game before operation to prevent the game from working
improperly when operated.
Checking item：
1) Check if the cord is securely plugged in and without defects.
2) Check the location of game.
3) Check if the game case is without defects or burrs.
4) Check if the game without dirt and properly stuck on with marks.

14
6. DAILY OPERATION
6.1 INPUT POWER TO OPERATE
1) Turn on the machine power switch.
2) Visually check the game and confirm the display can work properly.
3) Check the sound if it is ok.
4) Confirm the coin mech, fire button and the machine movement is
normal.
Warning：Before operation, please confirm all the items above are ok.
6.2 CHECK AFTER OPERATION
1) Check the display of the game and confirm it is proper.
2) Double check the coin mech, fire button and the machine movement is
normal; if it has any problems, please solve the problem as soon as
possible.
6.3 COLLECT COINS AND KEEP RECORD
1) Switch off the power and open the door of the coin box to take out the
coins
2) Open the door of the coin mech to keep a record of the coins’ quantity.

15
7. GAME SETTING
7.1 KEYS FOR SETTING
Setting Board
SW1
TEST
SERVE
SELECT
ENTER
ERASE
setting
free
change
SELECT: Choose the setting item.
TEST: Enter into the setting menu or skip to the next menu.
ENTER: Change the setting.
SERVE: Free to play.

16
7.2 SETTING METHOD
Setting method: press “TEST” to enter into the game setting menu →press the
“SELECT” to choose the setting item →press “ENTER” to change the setting
→press “TEST” exit setting.
7.3 SETTING DESCRIPTION
1) 1) Game setting interface：
1 COIN[S]/1 CREDIT[S]
SETUP 1
MODULATE VOLUME 20
LANGUAGE SELECT ENGLISH
SOUND SELECT ON
Descriptions:
1COIN[S]/1CREDIT[S]：this setting can decide how many coins for how many
playing time, if set to “1COIN[S]/1 CREDIT[S]”, it means insert 1 coins for
1 game.
MODULATE VOLUME：this setting can decide the volume, the higher value,
the larger output volume.
LANGUAGE SELECT: this setting decides which language will be displayed in
screen, Chinese or English.
SOUND SELECT: this setting decides if the machine with demo sound, if set to
“ON”, it means with demo sound while standby.

17
2) Testing the display
When the screen color is no white, the display can be judged to failure.

18
9. ADJUSTMENT
8.1 ADJUT THE COIN MECH
adjusting chip in
coin entrence
coin-return
pole
Adjusting Switch For
Coin Signal
Wavelength
switch for coin signal
Port For Power/Signal
Input
Micro-Resistance
sample
coin
chute
DC+12V
STRICT SLACK
Sensitivity
+-
COIN
Remove
REPLACE
Backward
SW3
100ms SLOW
25ms FAST
NOM
正常
MGN
精准
50ms MEDIUM
WHITE
COUNTER(+/-)
GROUND
N.C.
SW1
SW2
N.O.
COUNTER(-/+)
COIN SIGNAL
GRAY
BLACK
RED
GRAY
Descriptions:
1): Please take out the plastic coin from sample coin chute and replace it
with token.
2): Remove the screws on back of coin entrance. Adjust the fixing chip on
back of coin entrance according to the token’s diameter, which prevent
blocking the coin mech as inserting the large coin in by mistake.
3): Turn the COIN Switch to “NO” (COIN Signal wire and GND should be
disconnected at usual time). Turning switch can be used as the coin
mech switch when the game is power on.
4): Adjust the adjusting switch of COIN Signal wave length to 50MS.
5): Adjust the micro-adjusting resistance of token tolerance. Clockwise:
increasing the sensitivity of token tolerance, that is, the range of
accepting the token tolerance will be larger. Counter clockwise:

19
decrease the sensitivity, that is, the range will be smaller and choose
the token more strictly.
8.2 MAIN BOARD ADJUSTMENT
Diagram of main board:
Descriptions:
Annulling Button: pressing this button can set the Game Setting to default
and clear the data of Coin and Ticket saved in PCB.
Volume Adjustment: Use a flat screwdriver to twist the volume
potentiometer to adjust the volume level of the machine. Turning clockwise
will increase the volume; counterclockwise will decrease the volume.
！warning
The battery can save the data of game settings and coin number when the
power off. Please replace the battery when the machine can not save the
game setting.

20
9. CHECK AND MAINTAIN
！warning
Please check and maintain the game by technicians.
Please power off the game when check and maintain.
Please do not put any tools into cabinet, otherwise it will cause problem.
After checking, please tightly screw the screws and close the door.
9.1Daily Check
ITEM DESCRIPTION
Coin mech Check whether the coin mech can work proper.
Fire button Check whether the button can launch
Motion Check whether the motion is proper
Sound Check whether the sound and the volume are ok.
Display Check if the displayed colors are proper.
Temperature、
humidity Check if the temperature and humidity is proper
9.2Daily Maintenance
ITEM DESCRIPTION
Cabinet Clean the cabinet with water and soft paper.
Monitor Clean the ABS for monitor with water and soft
paper.
PCB Sweep the dust and dirty in the board with small
brush
Air Tank Open the valve under the air tank to release the
water.（once erery two weeks）