Teknik Craft 5421419 User manual

Get crafty
Craft Tower
Craft Collection | Model 5421419
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-28
29-32
33-36
37-38
39
Pae 2
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LOWER RIGHT END (1)
B LOWER LEFT END (1)
C TOP (1)
D UPPER RIGHT END (1)
E PEG BOARD (1)
F UPPER BACK (1)
G SHELF (2)
H LOWER SHELF (1)
I LOWER BACK (1)
J CORK BOARD (1)
K LOWER BRACE (1)
L UPPER BRACE (1)
M BOTTOM (1)
N TURNTABLE BOTTOM (1)
O BASE (1)
P SHORT BASE MOLDING (2)
Q LONG BASE MOLDING (2)
R LEFT DRAWER SIDE (2)
S DRAWER BACK (2)
T RIGHT DRAWER SIDE (2)
U DRAWER BOTTOM (2)
V DRAWER FRONT (2)
W SHORT METAL SHELF (3)
X LONG METAL SHELF (3)
A
B
C
D
E
F
G
G
H
I
J
K
L
M
N
O
P
PQ
Q
R
R
S
S
T
T
U
U
V
V
W
W
W
X
X
X
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 28
3
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4 CAM SCREW - 28 4
CAM COVER CARD - 5
7
WOOD DOWEL - 20
5KNOB - 2
6
SILVER 1/2" FLAT HEAD SCREW - 16
18
SILVER 1-7/8" FLAT HEAD SCREW - 4
13
METAL PIN - 8
8
METAL BRACKET - 8
9WASHER - 10
10 11 SPACER - 6
SILVER 1" PAN HEAD SCREW - 10
15 SILVER 1/2" PAN HEAD SCREW - 42 17
Pae 4
SILVER 1-3/16" FLAT HEAD SCREW - 16
14
12 TURNTABLE - 1
19 SILVER 1116" MACHINE SCREW  2

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push twenty-eiht HIDDEN CAMS (3) into the LOWER
ENDS (A and B), UPPER RIGHT END (D), UPPER
BACK (F), LOWER BACK (I), CORK BOARD (J), SHORT
BASE MOLDINGS (P) and DRAWER SIDES (R and T).
Px 2
Tx 2
Rx 2
B
A
F
J
D
I
3
Arrow
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
3
Arrow
Arrow
3
(28 used)
Pae 5

å Flip the UPPER BACK (F) over and place a SPACER (11)
over each hole.
å Place the PEGBOARD (E) onto the SPACERS (11).
Fasten the PEGBOARD (E) to the UPPER BACK (F).
Turn six SILVER 1" PAN HEAD SCREWS (15) throuh six
WASHERS (10), throuh the PEGBOARD (E), throuh six
SPACERS (11) and into the UPPER BACK (F).
Step 2
11
10
(6 used)
(6 used)
F
E
SILVER 1" PAN HEAD SCREW
(6 used in this step)
15
Pae 6

å Flip the CORK BOARD (J) over.
å Turn four SILVER 1" PAN HEAD SCREWS (15) throuh
four WASHERS (10) and into the CORK BOARD (J).
Step 3
10
(4 used)
SILVER 1" PAN HEAD SCREW
(4 used in this step)
15
J
Pae 7
Just think. The sooner
you do this, the sooner
you do somethin else.

Step 4
Qx 2
Vx 2
A
B
H
C
F
J
4
4
å Turn twenty-eiht CAM SCREWS (4) into the LOWER
ENDS (A and B), TOP (C), UPPER BACK (F), LOWER
SHELF (H), CORK BOARD (J), LONG BASE
MOLDINGS (Q), and DRAWER FRONTS (V).
å NOTE: Use the exact holes shown.
(28 used)
Pae 8
Anled ede

å Insert two WOOD DOWELS (5) into the CORK BOARD (J).
Fasten the UPPER BRACE (L) to the CORK BOARD (J) by
pushin the UPPER BRACE (L) onto the WOOD DOWELS.
å Fasten the UPPER RIGHT END (D) to the CORK BOARD (J).
Tihten two HIDDEN CAMS.
Step 5
Pae 9
D
J
5
L
1
2
Surface with HIDDEN CAMS
Finished ede

å Insert two WOOD DOWELS (5) into the UPPER BRACE (L).
å Fasten the UPPER BACK (F) to the UPPER RIGHT END (D).
Tihten two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the UPPER BRACE
insert into the holes in the UPPER BACK.
Step 6
Pae 10
5
1
2
J
F
D
L