Teknik 5410416 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Laptop Desk
5410416 Oiled Wood
5411204 Soft White
5409936 Jamocha Wood
Sit and surf.
www.teknikoffice.co.uk Teknik

Table of Contents Assembly Tools Required
2-3
4-5
6-22
23-25
26-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E MODESTY PANEL (1)
F KEYBOARD SHELF (1)
G KEYBOARD FRONT (1)
H RIGHT FRONT LEG (1)
I LEFT FRONT LEG (1)
J REAR LEG (2)
K DRAWER FRONT (1)
P SIDE MOLDING (2)
D20 RIGHT DRAWER SIDE (1)
D21 LEFT DRAWER SIDE (1)
D74 DRAWER BACK (1)
D716 DRAWER BOTTOM (1)

Part Identification Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
I
J
K
P
P
J
D716
D20
D74
D21

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
ANGLE BRACKET - 3
5G
HIDDEN CAM - 16
1F
CAM COVER - 7
13P
PULL - 2
27K
CAM SCREW - 10
8F
SLIDE CAM - 2
10A CAM DOWEL - 6 2F
12H HINGE - 2
40AW CABINET RIGHT - 1 40AX CABINET LEFT - 1 40AY DRAWER RIGHT - 1 40AZ DRAWER LEFT - 1
40CA CABINET RIGHT - 1 40CB CABINET LEFT - 1 40CC DRAWER RIGHT - 1 40CD DRAWER LEFT - 1

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5
GOLD 1" MACHINE SCREW - 4
50S
BLACK 9/16" LARGE HEAD SCREW - 6
1S
BLACK 2-1/4" FLAT HEAD SCREW - 6
26S
BROWN 1" FLAT HEAD SCREW - 4
18S
GOLD 5/16" FLAT HEAD SCREW - 12
3S
SILVER 5/8" FLAT HEAD SCREW - 4
23S
SILVER 9/16" LARGE HEAD SCREW - 2
54S
BLACK 9/16" FLAT HEAD SCREW - 4
32S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C), and MODESTY PANEL (E). Then, insert the
metal end of six CAM DOWELS (2F) into the HIDDEN CAMS
in the ENDS (A and B) and UPRIGHT (C).
Page 6
(6 used)
A
B
C
E
(16 used)
1F
1F
1F
1F
Do not insert CAM DOWELS into this part.
Do not insert
CAM DOWELS
into these edges.
2F
Arrow
Arrow
Arrow
Arrow
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.

å Turn ten CAM SCREWS (8F) into the LEGS (H, I, and J).
å Fasten the FRONT LEGS (H and I) to the ENDS (A and B).
Tighten six HIDDEN CAMS.
Step 2
Page 7
A
B
H
I
J
J
H
I
8F
Curved edge
1
2
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These surfaces
should be even.
These surfaces
should be even.
Curved edge
Remember:
Righty tighty.
Lefty loosey.
(10 used)
Edge with CAM DOWELS

Step 3
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the
other surfaces of the ENDS (A and B) until the shoulders of
the SCREWS rest on the surfaces of the ENDS.
å Slide the SIDE MOLDINGS (P) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
Page 8
A
B
P
P
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Shoulder
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S

å Turn the ENDS (A and B) over and fasten the REAR
LEGS (J) to the ENDS. Use six BLACK 2-1/4" FLAT
HEAD SCREWS (26S).
Step 4
Page 9
A
B
J
J
Curved edge
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
BLACK 2-1/4" FLAT HEAD SCREW
(6 used in this step)
26S

Step 5
å Fasten the CABINET RIGHT (40CA) to the RIGHT END (A) and
CABINET LEFT (40CB) to the UPRIGHT (C). Use four GOLD
5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
Page 10
1
2
34A
C
43
2
1
H
Surface without
HIDDEN CAMS
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Finished edge
Roller end
Roller end
Surface with
HIDDEN CAMS