Teknik Craft 5423412 User manual

Wall Mounted Pegboard
with Thread Storage
Craft Collection | Model 5423412
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Get crafty.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
3
3
4-6
7
8
9-10
11
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Page 2
Electric drill with 1/4" bit
(ONLY in indicated step)
Pencil
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
SILVER 1-1/2" PAN HEAD SCREW - 2
4SILVER 7/16" PAN HEAD SCREW - 4 5
PEG - 24
1WALL ANCHOR - 2 2BRACKET - 2 3
A UNIT (1)
A

StepStep 1
Page 4
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn the UNIT (A) onto its front edges.
å Fasten the BRACKETS (3) to the UNIT (A) exactly as
shown. Use four SILVER 7/16" PAN HEAD SCREWS (5).
3
3
A
SILVER 7/16" PAN HEAD SCREW
(4 used in this step)
5

StepStep 2
å Stand your unit upright.
å Insert the PEGS (1) into the UNIT (A).
Page 5
A
(24 used)
1

Step
å The centers of the BRACKETS used to hang your unit are spaced 25-5/8" apart. With your tape measure, measure the
distance on your wall. Then, mark the locations on your wall with a pencil. The marks should be 2-5/16" down from
the top of your unit.
å Next, drill the holes that are marked on the wall using a 1/4" drill bit.
å NOTE: If attaching the Thread Storage to a wall made of concrete, plaster, or other material, go to your local hardware
store for proper hardware.
å Using your hammer, gently tap the WALL ANCHORS (2) into the holes in your wall. Then, turn two SILVER 1-1/2" PAN
HEAD SCREWS (4) into the WALL ANCHORS (2).
å NOTE: Do not use a power screwdriver to tighten the SCREWS.
å NOTE: Do not completely tighten the SCREWS. There should be approximately a 3/16" gap between the SCREW and
WALL ANCHOR.
å Carefully insert the SCREWS in your wall into the large holes in the brackets on the back of your unit. Then set the unit
down into place.
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
Step 3
Page 6
The wall
SILVER 1-1/2" PAN HEAD SCREW
(2 used in this step)
4
25-5/8"
Top of your unit
2-5/16"
2
4
10 lbs. total

WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damage to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Properly mounting the shelf to the wall. • If not properly mounted, the shelf can fall
from the wall and cause injury and damage. • Carefully review and follow the mounting instructions contained in this manual.
• Overloaded shelves. • Risk of injury or property damage.
• Overloaded furniture can break. • Never exceed the weight limits shown in the instructions.
• Improper use of furniture to support TV’s.
• Placing TV’s on furniture items not
intended to support them is hazardous.
• Risk of injury or death. TV’s can be very
heavy. Plus the weight and location of
the picture screen can make furniture tip
forward.
• This product is not designed to support a
television.