Teknik White Home Study L-Shaped Desk User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
White Home Study L-Shaped Desk
Model 5427718
Sit and surf.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4-5
6
7-42
43-47
48-52
53-54
55
Page 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C SMALL TOP (1)
D LARGE TOP (1)
D32 LARGE LEFT DRAWER SIDE (1)
D33 LARGE RIGHT DRAWER SIDE (1)
D53 SMALL RIGHT DRAWER SIDE (1)
D59 SMALL LEFT DRAWER SIDE (1)
D78 LARGE DRAWER BACK (1)
D109 SMALL DRAWER BACK (1)
D707 SMALL DRAWER BOTTOM (1)
D708 LARGE DRAWER BOTTOM (1)
E LEFT UPRIGHT (1)
F LEFT FRONT LEG (3)
G RIGHT FRONT LEG (3)
H CORNER UPRIGHT (1)
J LARGE MODESTY PANEL (1)
K SMALL MODESTY PANEL (1)
L SHELF (1)
M BOTTOM (1)
N SMALL DRAWER FRONT (1)
O BACK (1)
P LONG TOP MOLDING (1)
Q SHORT TOP MOLDING (1)
R BOTTOM MOLDING (1)
S LEFT REAR LEG (1)
T RIGHT REAR LEG (1)
U LARGE DRAWER FRONT (1)

Part Identification
Page 3
A
B
C
D
EF
G
HJ
K
L
MN
O
P
Q
R
S
T
U
D33
D707
F
G
F
G
D708
D32
D78
D59
D53
D109
Now you know
our ABCs.

Hardware Identification
Page 4
45BA CABINET RIGHT - 1 45BD DRAWER LEFT - 1 45BC DRAWER RIGHT - 1 45BB CABINET LEFT - 1
(EXTENSION SET SHOWN SEPARATED)
EXTENSION SLIDE - 2
45MC
EXTENSION RAIL - 2
45MA FILE GLIDE - 2
5B FILE ROD - 2 8B
HIDDEN CAM - 30
1F CAM SCREW - 30 8F 12F TWIST-LOCK®
FASTENER - 27 WOOD DOWEL - 11
15F
ANGLE BRACKET - 7
5G SMALL DRAWER
FRONT BRACKET - 1
7G LARGE DRAWER
FRONT BRACKET - 2
10G PLATE - 3 41G
KNOB - 2
111K
GROMMET CAP - 2
1P GROMMET - 2 10P SCREW
COVER - 6
17P CAM
COVER - 18
19P

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5
BLACK 9/16" LARGE HEAD SCREW - 32
1S 3S GOLD 5/16" FLAT HEAD SCREW - 16
SILVER 1-1/8" FLAT HEAD SCREW - 4
10S 30S BLACK 1-9/16" FLAT HEAD SCREW - 8
SILVER 1/2" MACHINE SCREW - 1
38S GOLD 1" MACHINE SCREW - 1
50S
BLACK 1-15/16" FLAT HEAD SCREW - 5
113S

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
Page 6

Step 1
å NOTE: Two people are needed to build this unit.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push two SAUDER TWIST-LOCK®
FASTENERS (12F) into the large holes in the RIGHT END (A).
å Insert one WOOD DOWEL (15F) into the RIGHT END (A).
Page 7
A
12F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
15F

å Push six HIDDEN CAMS (1F) into the RIGHT END (A).
å Turn six CAM SCREWS (8F) into the LEGS (F and G).
Step 2
Page 8
A
F
G8F
1F
Arrow
1F
Arrow

å Insert two WOOD DOWELS (15F) into the LEGS (F and G).
å Fasten the LEGS (F and G) to the RIGHT END (A). Tighten
six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEGS insert into
the END.
Step 3
Page 9
F
G
A
These surfaces
should be even.
15F
The LEGS will
overhang this edge.
Surface with HIDDEN CAMS
Edge with
TWIST-LOCK®
FASTENERS
15F

å Push six SAUDER TWIST-LOCK® FASTENERS (12F) into
the large holes in the LARGE MODESTY PANEL (J).
Step 4
Page 10
12F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
J
12F