Teknik 5425304 User manual

Canyon Lane Desk
Model 5425304
Sit and surf.
Teknik
www.teknikoffie.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
3
4
5-18
19-21
22-24
25-26
27
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B BACK (1)
C SMALL FIXED SHELF (1)
D UPRIGHT (1)
E BOTTOM (1)
F LARGE FIXED SHELF (1)
G TOP (1)
H MODESTY PANEL (1)
J LEG (4)
K LEFT END (1)
L DOOR (1)
M ADJUSTABLE SHELF (1)
N BASE (1)
Page 3
A
BC
D
EF
G
H
L
M
N
J
K
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
SHELF PIN - 4
5
STRIKE PLATE - 1
9
HINGE - 2
8
BLACK 3/4" MACHINE SCREW - 2
15
BLACK 1-9/16" PAN HEAD SCREW - 5
13
BLACK 1-3/16" HEX HEAD SCREW - 2
14
BLACK 1/2" HEX HEAD SCREW - 8
17
L-WRENCH - 1
11
HIDDEN CAM - 13
1CAM SCREW - 13 2
PULL - 1
10
LONG WOOD
DOWEL - 2
3
BLACK 1-7/8" HEX HEAD SCREW - 2
12
BLACK 5/8" FLAT HEAD SCREW - 2
16
BLACK 1/2" FLAT HEAD SCREW - 2
19
SILVER 1/2" FLAT HEAD SCREW - 12
18
SHORT WOOD
DOWEL - 18
4
MAGNETIC CATCH - 1
6APPLIQUE CARD - 2 7

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push four HIDDEN CAMS (1) into the RIGHT END (A) and BACK (B).
å Turn three CAM SCREWS (2) into the RIGHT END (A).
å Insert two SHORT WOOD DOWELS (4) into the RIGHT END (A).
å Fasten the RIGHT END (A) to the BACK (B). Tighten one
HIDDEN CAM.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into
the BACK.
Page 6
2
Arrow
1
Arrow
1
4
4A
B
A
B
Remember:
Righty tighty.
Lefty loosey.

å Push four HIDDEN CAMS (1) into the SMALL FIXED SHELF (C).
å Fasten the MAGNETIC CATCH (6) to the SMALL FIXED SHELF (C).
Use two BLACK 5/8" FLAT HEAD SCREWS (16).
å Insert two SHORT WOOD DOWELS (4) into the RIGHT END (A).
å Fasten the SMALL FIXED SHELF (C) to the RIGHT END (A). Tighten
two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into
the SMALL FIXED SHELF.
Step 2
Page 7
Arrow
1
Arrow
1
A
4
C
C
6
BLACK 5/8" FLAT HEAD SCREW
(2 used in this step)
16
The MAGNETIC
CATCH must be here.

å Turn two CAM SCREWS (2) into the UPRIGHT (D).
å Carefully flip the UPRIGHT (D) over.
å Turn three CAM SCREWS (2) into this surface of the UPRIGHT (D).
å Push two HIDDEN CAMS (1) into the UPRIGHT (D).
å Insert two SHORT WOOD DOWELS (4) into the UPRIGHT (D).
å Fasten the UPRIGHT (D) to the BACK (B) and SMALL FIXED SHELF (C). Tighten three HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWEL in the UPRIGHT inserts into the BACK.
Step 3
Page 8
B
C
D
D
D
Surface with
fewer holes
F
L
I
P
O
V
E
R
2
Arrow
1
4

å Insert four SHORT WOOD DOWELS (4) into the RIGHT END (A)
and UPRIGHT (D).
å Fasten the BOTTOM (E) to the RIGHT END (A) and UPRIGHT (D).
Use four BLACK 1-9/16" PAN HEAD SCREWS (13).
å NOTE: Be sure the WOOD DOWELS in the RIGHT END and
UPRIGHT insert into the BOTTOM.
Step 4
Page 9
4
D
A
E
BLACK 1-9/16" PAN HEAD SCREW
(4 used in this step)
13
4

å Insert two HIDDEN CAMS (1) into the LARGE FIXED SHELF (F).
å Insert two LONG WOOD DOWELS (3) into the edge of the
LARGE FIXED SHELF (F).
å Fasten the LARGE FIXED SHELF (F) to the UPRIGHT (D). Tighten
two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LARGE FIXED SHELF
insert through the UPRIGHT (D) and into the edge of the SMALL
FIXED SHELF (C).
Step 5
Page 10
Arrow
1
3
D
F
F
Surface with
HIDDEN CAMS
C