Teknik Hythe 5426438 User manual

Get all organized
and stu.
02/21/20
Model 5426438
Hythe Wall Mounted 4 Shelf Boookcase with
Drawers
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-24
Pae 2
Electric drill with 5/16" bit
(ONLY in indicated step)
Hammer
Not actual size

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A SHELF (1)
B LEFT END (1)
C RIGHT END (1)
D SMALL DRAWER FRONT (1)
E LARGE DRAWER FRONT (1)
F BRACE (1)
G BACK (1)
H BOTTOM (1)
J SMALL LEFT DRAWER SIDE (1)
K SMALL RIGHT DRAWER SIDE (1)
L LARGE LEFT DRAWER SIDE (1)
M LARGE RIGHT DRAWER SIDE (1)
N SMALL DRAWER BACK (1)
O DRAWER BOTTOM (2)
P LARGE DRAWER BACK (1)
Q UPPER FRAME (2)
R LOWER FRAME (2)
S UPPER SHELF (3)
A
B
C
D
E
F
G
HJ
K
L
M
N
O
O
P
Q
Q
R
R
S
S
S
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
EXTENSION RAIL - 2
1
(EXTENSION SET SHOWN SEPARATED)
EXTENSION SLIDE - 2
2CABINET RIGHT - 1 3CABINET LEFT - 1 4
DRAWER RIGHT - 1
5DRAWER LEFT - 1 6
1-3/16" FLAT HEAD SCREW - 8
18
1/2" FLAT HEAD SCREW - 24
20
1/2" HEX HEAD SCREW - 8
19
1-7/8" HEX HEAD SCREW - 20
16
APPLIQUE CARD - 2
14
1-9/16" PAN HEAD SCREW - 4
17
2" PAN HEAD SCREW - 2
15
HIDDEN CAM - 14
9
L-WRENCH - 1
8
CAM SCREW - 14
10 WOOD DOWEL - 6 1311 PULL - 2 WALL ANCHOR - 2 12
FILE ROD - 2
7
21 38" MACHINE SCREW  4
Pae 4

Hardware Usae Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
ently tap the CAM DOWEL
until the shoulder is aainst
the surface of the part.
1.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tihten the HIDDEN CAM.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
ede of the board.
Hole
2.
Pae 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Turn two CAM SCREWS (10) into the ENDS (B and C).
å Push four HIDDEN CAMS (9) into the ENDS (B and C).
B
C
Pae 6
10
10
9
Arrow

Step 2
B
C
Pae 7
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as
shown in the upper diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (1) to the ENDS (B and C). Use six 1/2"
FLAT HEAD SCREWS (20).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlared diaram. Then, slide the inner cartride of the EXTENSION
RAIL in to find the other holes that line up with the holes in the ENDS.
Turn a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Push the black lever in and pull the SLIDE from the RAIL.
12
1/2" FLAT HEAD SCREW
(6 used in this step)
20
1
1
Open end
Open end
Remember:
Rihty tihty.
Lefty loosey.

Step 3
B
C
Pae 8
3
4
å Fasten the CABINET RIGHT (3) to the RIGHT END (C) and
the CABINET LEFT (4) to the LEFT END (B). Use six 1/2"
FLAT HEAD SCREWS (20) throuh the 2nd, 6th and 10th
hole from the roller end.
1/2" FLAT HEAD SCREW
(6 used in this step)
20
Groove
Roller end
Roller end

å Push two HIDDEN CAMS (9) into the BRACE (F).
å Insert a WOOD DOWEL (13) into each END (B and C).
å Fasten the ENDS (B and C) to the BRACE (F). Tihten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the BRACE.
Step 4
B
C
F
Pae 9
Arrow
9
13
F
Surface with HIDDEN CAMS

Step 5
Pae 10
å Turn four CAM SCREWS (10) into the SHELF (A).
å Insert two WOOD DOWELS (13) into the SHELF (A).
å Fasten the SHELF (A) to the ENDS (B and C). Tihten four
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SHELF insert
into the ENDS.
10
10
13
A
A
B
C
Groove