Teknik 5427030 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Prime Oak Computer Desk
Model 5427030
For all your
newfangled gadgetry.
Teknik
www.teknikoffice.co.uk

Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
2-3
4-5
9
6-37
38-42
43-47
48-50
51
Table of Contents
A RIGHT END (1)
B LEFT END (1)
C SMALL SKIRT (4)
D LARGE SKIRT (4)
D78 DRAWER BACK (1)
D87 RIGHT DRAWER SIDE (1)
D88 LEFT DRAWER SIDE (1)
D708 DRAWER BOTTOM (1)
E ADJUSTABLE SHELF (1)
F MODESTY PANEL (1)
G DRAWER FRONT (1)
H BOTTOM (2)
J UPPER ADJUSTABLE SHELF (1)
K FIXED SHELF (1)
L RIGHT TOP MOLDING (1)
M FRONT TOP MOLDING (1)
N TOP (1)
O BACK (2)
P LEFT TOP MOLDING (1)
Q SHELF MOLDING (1)
R LEFT UPRIGHT (1)
S RIGHT UPRIGHT (1)
T DOOR (1)
Tape Measure
427030 www.sauder.com/servicePage 2
Part Identification Now you know
our ABCs.
Hammer
Not actual size

Part Identification
A
T
B
C
C
C
C
D
D
D
D
E
F
G
H
H
J
K
L
M
N
O
O
P
Q
R
S
D78
D88
D87
D708
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
FILE GLIDE - 2
6B
EXTENSION SLIDE - 2
40MC
EXTENSION RAIL - 2
40MA 10A SLIDE CAM - 2
METAL
BRACKET - 8
4G 31G CORNER BRACKET - 8 MAGNETIC CATCH - 1 3I
42H HINGE - 2
FILE ROD - 2
8B MOLDING
CONNECTOR - 2
17F
WOOD
DOWEL - 8
15F 37F TWIST-LOCK®
FASTENER - 14
GROMMET CAP - 3
1P CORD CLIP - 4 4P
STRIKE PLATE - 1
6I 191K PULL - 2
GROMMET - 3
10P SHELF REST - 8
10R
105P TWIST-LOCK®
FASTENER COVER - 10
HIDDEN WIRELESS Qi COMPATIBLE
CHARGER by EGGTRONIC - Item 425905
(sold separately)
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
Page 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1/2" FLAT HEAD SCREW - 1
11S BLACK 2-1/4" FLAT HEAD SCREW - 4 26S
BLACK 7/8" MACHINE SCREW - 4
37S30S BLACK 1-9/16" FLAT HEAD SCREW - 4
BLACK 9/16" LARGE HEAD SCREW - 72
1S 3S GOLD 5/16" FLAT HEAD SCREW - 8
BROWN 1-5/8" FLAT HEAD SCREW - 8
55S BLACK 1-15/16" FLAT HEAD SCREW - 8
113S
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push four CORD CLIPS (4P) into the holes in the TOP (N).
å NOTE: The CORD CLIPS are used to hold electric cords to
the TOP.
N
4P
Page 6
Just think. The sooner
you do this, the sooner
you do something else.

å Tap two MOLDING CONNECTORS (17F) into the notches
in the MOLDINGS (L, M, and P).
Step 2
L
M
M
P
P
Flat end
17F
Flat end
17F
Unfinished surface
17F
Page 7
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS.

å Carefully flip the MOLDINGS (L, M and P) over, and fasten
them to the TOP (N). Use eight BROWN 1-5/8" FLAT
HEAD SCREWS (55S).
å NOTE: Start each SCREW a few turns before completely
tightening any of them.
å NOTE: Do not overtighten the SCREWS into the TOP.
Step 3
N
L
M
P
BROWN 1-5/8" FLAT HEAD SCREW
(8 used in this step)
55S
Page 8

å Push two SAUDER TWIST-LOCK® FASTENERS (37F) into
the large holes in the MODESTY PANEL (F).
Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Step 4
Do not tighten the TWIST-LOCK® FASTENERS in this step.
37F
F
427030www.sauder.com/service Page 9

Step 5
F
N
å Fasten the MODESTY PANEL (F) to the TOP (N).
Tighten two TWIST-LOCK® FASTENERS.
Surface with TWIST-LOCK® FASTENERS
Page 10