Teknik 5427428 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Hudson Elm finish | Model 5427428 English pg 1-12
Français pg 13-14
Español pg 15-16
Lot # 573100 11/22/21
Purchased: __________________
1500x870 Bow Front
Desk
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
8
5-12
13-14
15-16
17-18
19
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D MODESTY PANEL (1)
A
B
C
D
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
46E LEVELER - 4
10M TOUCH-UP PEN - 1 2P GROMMET - 2
3P GROMMET
CAP - 2 9P CORD CLIP - 2
42F WOOD DOWEL - 13
TWIST-LOCK®
FASTENER COVER - 15
125P HOLE
PLUG - 8
127P
Page 4

Optional Accessories (sold separately)
å This piece of furniture accommodates one or more of the following optional accessories (sold separately).
å Powered Grommet (Item 427829)
å Articulating Keyboard Shelf (Item 426468)
The Articulating Keyboard Shelf is designed to be fastened to the underside of your desk, desk return, or credenza top.
å LED Light (Item 426494)
The LED Light is designed to be fastened to the underside of a hutch.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert four WOOD DOWELS (42F) into the MODESTY
PANEL (D) exactly as shown.
å NOTE: You may need to gently tap the WOOD DOWEL in
with your hammer.
42F
42F
D
Page 6

Step 2
å Using your hammer, gently tap four LEVELERS (46E)
completely into the holes in the ENDS (A and B).
å NOTE: Adjustments to the LEVELERS will be made later in
assembly once your unit is standing upright.
A
B
46E
Page 7

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Page 8

Step 3
å Fasten the ENDS (A and B) to the MODESTY PANEL (D).
Tighten six TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the MODESTY
PANEL insert into the ENDS.
A
D
B
Surface with
TWIST-LOCK®
FASTENERS
Surface with TWIST-LOCK® FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
For support, place packing
foam or books here.
Edge with TWIST-LOCK® FASTENERS
Page 9

Step 4
å Push two CORD CLIPS (9P) into the holes in the TOP (C).
å NOTE: The CORD CLIP is used to hold the cord against
the TOP.
C
9P
Pilot hole to be used
only if you purchased
the optional
426468 Articulating
Keyboard Shelf.
Page 10