Teknik Craft 5421416 User manual

Oranizer Hutch
Craft Collection | Model 5421416
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Knick-knack
paddywhack,
ive your stu a home.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
3
4
5-19
20-22
23-25
26
27
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Pae 2
Short Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D SHELF (1)
E BACK (1)
F LEFT UPRIGHT (1)
G RIGHT UPRIGHT (1)
H DIVIDER (1)
I LEFT DRAWER FRONT (1)
J RIGHT DRAWER FRONT (1)
K LEFT DRAWER SIDE (2)
L RIGHT DRAWER SIDE (2)
M DRAWER BACK (2)
N DRAWER BOTTOM (2)
A
B
C
D
EF
G
H
I
J
K
L
M
N
K
L
M
N
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 26
3CAM SCREW - 26 4
CAM COVER CARD - 4
6
KNOB - 2
5
SILVER 1/2" FLAT HEAD SCREW - 16
12
LEFT CONNECTOR
PLATE - 1
8
RIGHT CONNECTOR
PLATE - 1
7
SILVER 13/16" PAN HEAD SCREW - 10
11
9SILVER 1316" FLAT HEAD SCREW  15
LEFT EXTENSION
RAIL/SLIDE- 2
1RIGHT EXTENSION
RAIL/SLIDE- 2
2
Pae 4
13 SILVER 1116" MACHINE SCREW  2

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Fasten a RIGHT EXTENSION RAIL/SLIDE (2) to the
DIVIDER (H) as shown in the left diaram. Use two SILVER
1/2" FLAT HEAD SCREWS (12).
å Turn over the DIVIDER (H) and fasten a LEFT EXTENSION
RAIL/SLIDE (1) to the DIVIDER as shown in the riht
diaram. Use two SILVER 1/2" FLAT HEAD SCREWS (12).
180°
Pae 5
HH
2
1
SILVER 1/2" FLAT HEAD SCREW
(4 used in this step)
12
Use the 6th hole from the
back ede and the 3rd
hole from the front ede.
Finished (front) ede
Back ede
Use the 8th hole from the
back ede and the 1st hole
from the front ede.
Back ede
Finished (front) ede
Open end
Open end
The holes must be
closer to this ede.

Step 2
Pae 6
å Fasten the remainin LEFT EXTENSION RAIL/SLIDE (1) to
the LEFT END (B) as shown in the left diaram. Use two
SILVER 1/2" FLAT HEAD SCREWS (12).
å Fasten the remainin RIGHT EXTENSION RAIL/SLIDE (2)
to the RIGHT END (A) as shown in the riht diaram. Use
two SILVER 1/2" FLAT HEAD SCREWS (12).
B
A
1
2
SILVER 1/2" FLAT HEAD SCREW
(4 used in this step)
12
Use the 6th hole from the
back ede and the 3rd
hole from the front ede.
Back ede Back ede
Finished
(front) ede
Open end
Open end
Finished
(front) ede

Step 3
Pae 7
B A
å Turn eiht CAM SCREWS (4) into the ENDS (A and B).
4
(8 used)

å Fasten the UPRIGHTS (F and G) to the SHELF (D).
Use four SILVER 1-3/16" FLAT HEAD SCREWS (9).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 4
Pae 8
D
F
G
Surface with more holes
Surface with holes
SILVER 1-3/16" FLAT HEAD SCREW
(4 used in this step)
9
Surface with holes
Finished ede

å Push two HIDDEN CAMS (3) into the DIVIDER (H).
å Turn two CAM SCREWS (4) into the SHELF (D).
å Fasten the DIVIDER (H) to the SHELF (D). Tihten two
HIDDEN CAMS.
Step 5
Pae 9
D
H
4
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
3
Arrow

å Position the UPRIGHTS (F and G) as shown.
å Fasten the BACK (E) to the UPRIGHTS (F and G) and
DIVIDER (H). Use three SILVER 1-3/16" FLAT HEAD
SCREWS (9).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 6
Pae 10
E
H
SILVER 1-3/16" FLAT HEAD SCREW
(3 used in this step)
9
F
G
Lare hole
Surface with more holes