teko Astra-4511 User manual

Astra-4511
Wireless manual fire call point
User Guide
Manufacturer:
ZAO NTC TEKO
420108 Kazan, Russia
Gafuri 71
[phone]
[email protected]
www.teko.biz
Made in Russia
Ver. 4511rk2-v3_0_instr_en
1 FUNCTION
The detector is designed to manually turn on
the fire alarm signal by pressing the drive ele-
ment, generate a fire notification and transmit
the notification via radio to the Astra-812 Pro
control panel directly or via the Astra-WE 433
radio extender or to the Security hub.
The detector supports two-way radio exchange.
2 SPECIFICATION
Wieless coverage range,
line-of-sight, m, not less...............................300
Operating frequency range, MHz .................433
Supply voltage, V........................from 2.1 to 3.0
Overall dimensions, mm...............110 × 94 × 47
Operation conditions
Temperature range, °С............from - 10 to + 55
Relative air humidity, % ...........up to 93 at + 40 °С
Without moisture condensation
3 DELIVERY SET
Detector delivery set includes: mounting parts
(dowel –2 pcs., screw –2 pcs.,), special key for
opening –1 pc., key pusher –1 pc., battery
(CR123A, 3V) - 2 pcs. (installed), user guide –
1 copy.
4 INDICATION
Notification
Indication
Boot time
1x red flash then 1x white led
flash
Norm
1x red flash in 60 sec. period
Fire alarm
1x red flash every 2 sec. until
the fire factor is eliminated.
2x flashing in a period of 25
sec. when eliminating the fire
factor before receiving a
command from the controller
Test fire
1x red flash in every 2 sec.
during 30 sec. when receiv-
ing the test command from
the Astra-942 laser remote
control
Power failure
3x red flash in 25 sec. period
Tampering /
Restore tam-
pering
1x red flash
Searching
connection
5x white flash in 1 sec.
No connection
2x white flash in 25 sec.
period
Reset
2x white flash in 1-2 sec.
Laser tool
command
1x red flash for 2 sec.
Notes
1 When the message “Power failure” appears,
the battery must be replaced within two months.
2 Indication of notifications "Power failure", "No
network", "Search for network" goes off 60
minutes after turning on the power supply. The
indication turns on again for 60 minutes after
receiving the "Test" command from the Astra-
942 laser tool.

5 ASSIGNING TO THE SYSTEM
1) Start registration on the Astra-812 Pro, Secu-
rity Hub mobile or desktop app. Registration
starts for 45-60 sec.
2) Turn on the detector by pulling out the bat-
tery insulator or by installing the battery.
3) Detectors led start flashing: 5x white flash in
1 sec –searching of connection.
If after 4 sec. the display appears "No connec-
tion", so the detector was previously registered
to another wireless network. In this case, you
need to reset detector (see p. 6) and repeat the
registration procedure. Before registration -
remove the battery and wait at least 20 sec.
4) Make sure that the registration is successful.
If registration is unsuccessful, repeat the proce-
dure.
ATTENTION!
Do not turn off the detector until end of reg-
istration of all radio devices!
6 RESET PROCEDURE
•Removing the detector from the wireless net-
work is carried out via the PKM Astra Pro soft-
ware or via the menu of the Astra-812 Pro con-
trol panel or via Security Hub mobile App.
•To reset the detector:
1) Open the detector.
2) Close the DEL contacts and hold for 5 sec. -
the red led will turn on.
3) After turning off the red led, open the DEL
contacts within 5 sec.
4) The detector generates a notification “No
connection” and becomes available for register-
ing to the system.
7 INSTALLATION PLACE
The detector is installed in an accessible place
along evacuation routes, in corridors, on land-
ings, at exits.
8 INSTALLATION PROCEDURE
1) Open the detector
using a special key.
2) Fix the base
3) Pull out the batteries insula-
tors or install batteries if
they were removed (first
backup “Secondary”, then
the main “Primary”).
4) Assemble the detector by
aligning the grooves of
the cover and the base of
the detector and sliding
the cover down until the
latch locks.
5) Run detector test (see p.
9).
9 TESTING
1) To activate the «Test»
mode:
- push the red button of the
laser tool;
-irradiate the LED for 1
sec. LED should turn on in
red for 2 sec.
2) Normal operation of the
detector: led on the detector will start flashing
with a period of 2 sec for 30 sec (“Test fire”
notification). In the event log of Astra-812 Pro,
PKM Astra Pro, the entry "Test fire" will be
made.
Note –WE 433 leds don’t display test fire.
10 WARRANTY
Operational warranty period: 5 years from the
date of commissioning, but no more than 5
years 6 months from the date of manufacture
and subject to current user guide requirements.
b
Mounting
holes