THE SHOWER LAB VIEW 19.3H User manual
10/2021 V 1.1
VIEW 19.3H Illustration - View 19.3H
SB1 Stay Bar
10/2021 V 1.1
VIEW 19.3H
IMPORTANT
•This shower screen / enclosure must be installed by suitably qualified individuals. We
recommend a minimum of two people for safe assembly of certain sections of this screen.
•Ensure all appropriate safety equipment, especially protective footwear, safety glasses
and gloves are used.
•When drilling holes in ceramic tiles, use masking tape to prevent the drill from slipping:
DO NOT use hammer action as this will crack the tiles. Use a high quality drill bit to ensure
a clean, precise hole.
Tighten hinges and brackets to the recommended 15.6N.
•
•
Please leave these instructions with the customer following installation.
PRIOR TO INSTALLATION
•Before disposing of the packaging and prior to commencing assembly, please check all
the components to ensure that they have been supplied correctly and are undamaged.
Subsequent claims for missing or damaged pieces will not be accepted once the
packaging has been disposed of and installation commenced.
•In the event of any queries please contact your supplier quoting the relevant model
information.
•The Tray / Tiled floor on which this screen is to be installed must be level on all sides.
•It may be necessary to use alternate fixings to those supplied, depending on the properties
of the walls to be fixed to.
•Use the protective corners supplied at all times until the glass is moved to its final position.
•Ensure that the glass is installed correctly, taking care to avoid installing the glass upside
down. On certain panels an easy clean coating is applied to one side only, this is clearly
marked with a sticker on the non-coated side. The coated surface is to be fitted inwards
towards the inside (wet side) of the screen.
•Ensure that all surfaces to be sealed are clean and dry prior to applying the silicone
sealant. Use a high grade fungal resistant sealant.
•Allow a minimum of 24 hours after application of the silicone sealant prior to using the
screen.
TOOLS & MATERIALS REQUIRED
Junior Hacksaw
Straight Edge (Steel
Rule)
Fine Tooth File
Set or Roofing
Square
Masking Tape
Modelling Knife
Spirit Level
Pencil
Silicone Gun
Power Drill
Ø6mm Masonry Drill Bit
2x Suction Glass Lifters
High Quality Silicone Sealant
Tape Measure
Pozi-drive
Screwdrivers, PZ1&2
Safety Glasses and
Gloves
CARE AND MAINTENANCE
(please ensure that these instructions are left with the installed unit)
•We recommend routine cleaning of your screen / enclosure with hot water using a soft
cloth, then drying with a dry soft cloth or chamois leather.
Ritec Aftercare for Shower Glass is recomended for best results.
•All glass has been treated with EASY CLEAN glass finish and care must be taken to avoid
any abrasive cleaning products that may damage the special surface protection.
•DO NOT use acidic based de-scaler products or products containing bleaches or solvents.
Digital Torque Wrench
10/2021 V 1.1
VIEW 19.3H
Underframe Wedge Gasket
x2
Underframe
x2
Underframe Gasket
x2
Wall Prole
x1
Wall Prole Soft Seal
x1
Wall Prole Rigid Seal
x1
Supplied Parts
Bottom Door Seal
x1
Glass to Glass Bi-fold Seal
x1
Packers
10/2021 V 1.1
VIEW 19.3H
Supplied Parts
Glass Panel
x1
Nylon Block
x1
Underframe End Cap
x1
Wall Prole End Cap
x1
Underframe 90°Connector
x1
Spacers
Return Panel
x1
Door Panel
x1
Glass to Glass Hinge
x2
10/2021 V 1.1
VIEW 19.3H
Supplied Parts
Glass to Glass Adhesive Gasket
x1
10/2021 V 1.1
VIEW 19.3H
Supplied Parts
Please use this page to nd which stay bar your enclosure has been supplied with.
SB1 - With Glass Clamp
10/2021 V 1.1
VIEW 19.3H
These instructions are for the View 19.3H. An SB1 Stay Bar is used for this illustration.
The following instructions are valid for both the 20mm and 30mm proles. The 30mm prole is
used in the following instructions.
Please use the below diagram to reference the list of parts.
A
B
I
C
H
D
F
E
G
Return Panel
Door Panel
Fixed Inline Prole
Wall Prole End Cap
Wall Prole Soft Seal
Wall Prole Rigid Seal
Underframe Wedge Gasket
Underframe
JUnderframe Gasket
Wall Prole
N
M
K
L
Underframe 90°Connector
Underframe End Cap
Glass Adhesive Tape
Bottom Door Seal
OGlass to Glass Bi-fold Seal
PGlass to Glass Hinge
QStay Bar (SB1 Shown)
A
H
I
E
B
J
M
D
N
F
C
Q
L
P
O
G
K
10/2021 V 1.1
VIEW 19.3H
]GI 7QGjP IQOPj ]GI 7QGjP IQOPj
+" 6ÅÇÈ+ ÅÉÃÅÊÇ ÃÁÁÁ +" 6ÅÇÈ ÅÉÈ ÃÁÁÁ
6ÆÇÈ+ ÆÉÃÆÊÇ ÃÁÁÁ 6ÆÇÈ ÆÉÈ ÃÁÁÁ
6ÇÇÈ+ ÇÉÃÇÊÇ ÃÁÁÁ 6ÇÇÈ ÇÉÈ ÃÁÁÁ
6ÈÂÉ. ÈÄÄÈÅÈ ÃÁÁÁ 6ÈÇÈ ÈÉÈ ÃÁÁÁ
6ÈÆÉ. ÈÈÄÈÉÈ ÃÁÁÁ 6ÉÇÈ ÉÉÈ ÃÁÁÁ
6ÈÇÈ+ ÈÉÃÈÊÇ ÃÁÁÁ 6ÊÇÈ ÊÉÈ ÃÁÁÁ
6ÉÆÉ. ÉÈÄÉÉÈ ÃÁÁÁ 6ÂÁÇÈ ÂÁÉÈ ÃÁÁÁ
6ÉÇÈ+ ÉÉÃÉÊÇ ÃÁÁÁ 6ÂÂÇÈ ÂÂÉÈ ÃÁÁÁ
6ÊÆÉ. ÊÈÄÊÉÈ ÃÁÁÁ +" 6ÂÇÈ ÂÉÈ ÃÁÁÁ
6ÊÇÈ+ ÊÉÃÊÊÇ ÃÁÁÁ 6ÃÇÈ ÃÉÈ ÃÁÁÁ
6ÂÁÇÈ+ ÂÁÉÃÂÁÊÇ ÃÁÁÁ 6ÄÇÈ ÄÉÈ ÃÁÁÁ
6ÂÂÆÉ. ÂÂÈÄÂÂÉÈ ÃÁÁÁ 6ÅÇÈ ÅÉÈ ÃÁÁÁ
6ÂÂÇÈ+ ÂÂÉÃÂÂÊÇ ÃÁÁÁ
ADJUSTMENT SHEET
STANDARD ENCLOSURES - 30mm (CH30) Wall Profile
If you have a Bespoke Enclosure, reference the Install Sheet for the panel specifica�ons of the Enclosure.
CH30 - Bespoke Panel A Width: Panel A + 14 = Minimum Width + 14 = Maximum Width
CH20 - Bespoke Panel A Width: Panel A + 14 = Minimum Width + 4 = Maximum Width
Bespoke Panel B + C Width: Panel B + C + 25 = Width (Inlcuding 3mm Wall Profile Overlap)
BESPOKE ENCLOSURES - 30mm (CH30)/ 20mm (CH20) Wall Profiles
Dimensions to OUTSIDE of Wall Profile - See spec below
A
B
C
A
B
C
LH RH
10/2021 V 1.1
VIEW 19.3H
01/16
3mm minimum
Shower Tray
x - 22mm
R
01
04
10/2021 V 1.1
VIEW 19.3H
02/16
10/2021 V 1.1
VIEW 19.3H
03/16
Wet Side
Professional Tip
If drilling ceramic tiles, place
masking tape on the tiles before
marking and drill through the
tape to prevent the drill bit from
skidding.
DO NOT use Hammer Action as
this will break the tiles.
(No 8) Prole - Wall
(No 6) Prole - Top Cap
09 10
11 12
10/2021 V 1.1
VIEW 19.3H
6mm min
Wall ProleGlass Panel
04/16
13 14
4mm
10/2021 V 1.1
VIEW 19.3H
Glass Inline Panel
Glass Return Panel
Glass to Glass Adhesive Tape
05/16
If the Wall Profile is flush with the Glass
Panel, move on to step 18.
If the Wall Profile is not flush with the
top of the Glass Panel, mark the Wall
Profile. Using a straight edge, mark
where the wall channel needs to be
trimmed.
To protect the channel finish, it is
recommended to mark on masking
tape.
Clean the edges of the Glass Inline
Panel and Return Panel where the
Glass to Glass Adhesive Tape will be
applied.
Before Installing the Glass to Glass
Adhesive Tape, ensure that the Tape is
orientated and posi�oned correctly on
the Glass Inline Panel as shown below.
Posi�on the Glass to Glass Adhesive
tape on the correct edge of the Inline
Panel. Using a cloth or towel, apply the
Tape to the Panel.
Peel back the protec�ve adhesive strip
while firmly applying the Tape.
Cut excess Tape using a blade.
17 18
19 20
10/2021 V 1.1
VIEW 19.3H
06/16
WARNING
The glass is heavy and may
damage the oor or underframe if
handled incorrectly. It is advisable
to use a suitable non-slip
protective mat or piece of carpet.
Never rest the glass across the
underframe as this may cause
damage.
Glass Joint
21 22
23 24
10/2021 V 1.1
VIEW 19.3H
07/16
Silicone the
inside corner
25 26
27 28
Silicone
10/2021 V 1.1
VIEW 19.3H
Flush
Rigid Seal
Glass Panel
08/16
Apply the Rigid Seal to the dry side of
top.
29 30
31 32
10/2021 V 1.1
VIEW 19.3H
09/16
Start to pull the Return Panel back
when approaching the top.
Use the Nylon Block to ensure that the
Inline Panel is level with the edge of
the Return Panel.
Ensure the two panels are firmly fixed
together and remove Inline Packers.
Remove Packers and feed the Wedge
Gasket into the archway gap and trace
along the Glass on both sides.
Spray water on Glass Panel and use
Nylon Block to help feed Gasket.
Trim both Underframe Gasket Seals as
close to the edge as possible using a
blade.
Trim both of the Wall Profile seals at
the top face of the Wall Profile using a
blade.
33 34
35 36
X
X - 6.5mm
10/2021 V 1.1
VIEW 19.3H
10/16
Measure the distance from the inside
face (wet side) of the Inline Panel to
the wall opposite. Ensure this
measurement is truly horizontal.
Subtract 6.5mm to get your final
dimension.
Mark the final dimension on the Stay
Bar Tube, wrapped with some masking
tape. Carefully use a chop saw and fine
file to cut and finish the edge.
STAY BAR CONFIGURATION A - SB1
A1 A2
10/2021 V 1.1
VIEW 19.3H
11/16
With masking tape applied, place the
supplied Stay Bar Jig firmly at the
trimmed end of the Stay Bar and mark
the 2 holes with a pen.
Drill holes using a 5mm drill bit.
Assemble the Glass Clamp to the Stay
Bar as shown.
Secure the Glass Clamp over the panel
making sure the glass is fully inserted
into the groove.
Ensure the Stay Bar is square and level.
Mark the end loca�on on the wall.
Remove the Stay Bar.
STAY BAR CONFIGURATION A - SB1
Drill 1 side only
A3 A4
A5 A6
10/2021 V 1.1
VIEW 19.3H
Fix Glass Clamp over the Glass and
12/16
Professional Tip
If drilling ceramic tiles, place
masking tape on the tiles before
marking and drill through the
tape to prevent the drill bit from
skidding.
DO NOT use Hammer Action as
this will break the tiles.
STAY BAR CONFIGURATION A - SB1
A7 A8
A9
Other manuals for VIEW 19.3H
1
Table of contents
Other THE SHOWER LAB Bathroom Fixture manuals
THE SHOWER LAB
THE SHOWER LAB VIEW 19F User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 20 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 31DW User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 22 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 23 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 30 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 03 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 03 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 19.3H User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 25 User manual
THE SHOWER LAB
THE SHOWER LAB VR01S20 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 02 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 30 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 31DW User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 11 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 19.3F User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 02 VR02S59 User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 19H User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 31DP User manual
THE SHOWER LAB
THE SHOWER LAB VIEW 06 User manual
Popular Bathroom Fixture manuals by other brands
Noro
Noro SAND 0680 manual
Booth & Co
Booth & Co AXBRIDGE BC-AXB-183-CP installation guide
Hans Grohe
Hans Grohe AXOR Carlton 17430 Series Instructions for use/assembly instructions
Price Pfister
Price Pfister Classic Series installation instructions
Reece
Reece KADO Cirque quick start guide
Kohler
Kohler STRAYT 99166T-C4 installation instructions
