TJM T13 User manual

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 1 of 27
04/08/2023
Australian Standards Relating to Installing Vehicle Frontal Protection Systems (VFPS): AS 4876.1-2002
a) Do not attach V.F.P.S. to vehicle using anchorages not intended for this purpose (e.g., engine mounting bolts), other than those
specified by the V.F.P.S. manufacturer in this instruction.
b) Do not use this product for any vehicle make or model other than those specified by the V.F.P.S. manufacturer (as above).
c) Do not remove any plaques or labels from the V.F.P.S.
d) Do not modify the structure of the V.F.P.S. in any way.

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 2 of 27
04/08/2023
Item
No.
Description
Qty
Part
Number
PARTS LIST
1
T13 Outback Bar
1
F-36613
2
Winch Frame
1
F-33821
3
Inner Chassis Plate RH
1
F-33803R
4
Inner Chassis Plate LH
1
F-33803L
5
UBG Mount Assembly RH
1
F-34111R
6
UBG Mount Assembly LH
1
F-34111L
7
Bending Angle RH
1
F-33948R
8
Bending Angle LH
1
F-33948L
9
Washer Plate
2
F-32863
10
Sliding Washer Plate
2
F-34019
11
Number Plate Mount - Standard
1
F-32948
12
Number Plate Mount - Slimline
1
F-33279
13
Number Plate Mount
1
F-36813
14
Radar Grille
1
F-36621
15
Radar Cover Panel
1
F-34605
16
Centre Guard
1
F-34001
17
Wing Guard Mount RH
1
F-34107R
18
Wing Guard Mount LH
1
F-34107L
19
Wing Guard RH
1
F-34135R
20
Wing Guard LH
1
F-34135L
21
Camera Mount
1
F-36622
22
Camera Clamp
1
F-34200
23
LED Indicator/Park Light
2
92750
24
Number Plate Hinge Bush
2
K1292
25
Parking Sensor Housing Kit
6
F-5417
26
M8 Pull Plunger w/ Thin Nut
1
F-33789
N/A
Nylon Plug
4
K0665
N/A
Rated Recovery Point Label
1
HC0064
N/A
Recovery Point Use Guide
1
F-1768
30
Fog Light Blanking Plate
2
92091
31
Fog Light Washer Plate
2
88057
N/A
Pinch Weld –Steel Sprung (600mm)
1
93154
N/A
Bumper Cut Template
1
F-37031
FACTORY FITTED
N/A
Rated Recovery Point Label
1
HC0064
N/A
TJM LOGO Sticker
1
K3550
N/A
ABC Warning Label
2
HC0057
Item
No.
Description
Qty
Part
Number
BOLT KIT
N/A
M5 x 0.8 x 20mm Pan Head Screw
2
K0688
N/A
M5 x Ø10mm x 1.0mm Flat Washer
4
K0417
N/A
M5 x 0.8 Nyloc Nut
2
K0604
N/A
M6 x 1.0 x 20mm Button Head Bolt SS
29
K3218
N/A
M6 x 1.0 x 20mm Hex Head Bolt
11
K0550
N/A
M6 x 1.0 Cage Nut Type B
14
K1550
N/A
M6 x 1.0 Nyloc Nut SS
14
K1549
N/A
M6 x 1.0 Flange Nut
8
K3033
N/A
M6 x 2.5 x 1.2 Spring Washer SS
18
K1552
N/A
M6 x Ø12.5mm x 1.2mm Flat Washer SS
16
K1551
N/A
M6 x Ø12.5mm Flat Washer
8
K0897
N/A
M6 x Ø18mm x 1.6mm Flat Washer SS
28
K1554
N/A
M8 x 1.25 x 35mm Hex Head Bolt
2
K0555
N/A
M8 x 1.25 Nyloc Nut
2
K0606
N/A
M8 x Ø19mm x 18G Flat Washer
4
K0628
N/A
M10 x 1.5 x 25mm Button Head Bolt SS
4
K2690
N/A
M10 x 1.25 x 30mm Hex Head Bolt
8
K0564
N/A
M10 x 1.25 Nyloc Nut
8
K3099
N/A
M10 x 1.5 Nyloc Nut
2
K0607
N/A
M10 x 3.5 x 2.2 Spring Washer
2
K0621
N/A
M10 x Ø21mm x 2.0mm Flat Washer
14
K2900
N/A
M10 x Ø30mm x 3.0mm Flat Washer
8
WSST-W13
N/A
M12 x 1.25 x 35mm Hex Head Bolt
8
K0570
N/A
M12 x 1.25 x 40mm Hex Head Bolt
12
K0571
N/A
M12 x 1.25 Nyloc Nut
20
K1200
N/A
1/2" x Ø1-1/4” x 2.5mm Flat Washer
40
K0623

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 3 of 27
04/08/2023
Tools Required
Hand Tools
Power Tools
Metric Socket Set 8-19mm
Electric/Air Impact Driver (Optional)
Ratchet & Socket Extension Bar
Electric Drill
Metric Spanner Set 10-19mm
Air Saw
Torx Drivers T25-T30
Hex (Allen) Key Set 4-6mm
Trim Puller Tool
Flat Blade Screwdriver Set
Phillips Head Screwdriver Set
Utility Knife
Side Cutters
Pliers
Drill Bit Kit 3mm –10.5mm
Trim Removal Tool Set
Digital Angle Indicator
Consumables Required
Zip Ties
Masking Tape
Rust Preventative
Safety Equipment/Notice
Hearing Protection
Eye Protection
Lifting Hazard
Vehicle Support/Lifting
Must be worn when using
power tools.
Must be worn when
cutting, drilling, or
grinding.
Two persons lift or
mechanical lifting aid
required for FPS fitment.
Ensure vehicle is properly
supported before commencing
work.

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 4 of 27
04/08/2023
NOTES
•Before commencing fitment read instructions and ensure all listed components
are supplied.
•Left hand & right-hand components are determined as seated in the vehicle.
•The fitment of TJM products does not nullify the OE manufacturer's operating
guidelines and/or warnings. Ensure you are familiar with and adhere to the usage
instructions specified by the manufacturer in the owner's manual or other official
documentation.
•Check for (and remove) any build up in all threads fitted to the product.
•Ensure that the “Rated Recovery Point Label” is affixed alongside the compliance
label in the driver’s side doorjamb.
•When fitting accessories to TJM products (i.e., driving lights and aerials), ensure
suitable washer plates are used under the mounting surface that allow the
accessory to be secured in a way that prevents it from damaging the product.
•Where OE air guides require trimming, ensure minimal clearance between air
guides and TJM components to prevent air leakage which may adversely affect
vehicle cooling.
•When removing protective coatings, ensure all new edges are deburred, clean any
swarf from the area and apply rust preventative to exposed surfaces.
•Place the product on a soft workspace to prevent damage prior to installation.
Bolt tensions
Dia. (mm)
Nm
ft.lbs
Dia. (inch)
Nm
ft.lbs
All bolt tensions are
as follows unless
otherwise
specified.
5
5
4
1/4”
9
7
6
9
7
5/16”
22
15
8
22
16
3/8”
33
27
10
44
32
7/16”
55
43
12
77
57
1/2”
86
66

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 5 of 27
04/08/2023
1. Attach bumper trim template to the vehicle
and mark flare and bumper trim lines.
2. Remove and retain the number plate,
discarding the fasteners. Remove number
plate mount.
3. Remove and retain the plastic scrivets (11)
that secure the top of the grille/radiator
shroud. Remove shroud from vehicle and set
aside.
4. Remove and retain the top bolts (2) securing
the top of the grille to the vehicle.
5. Disconnect the camera plug and washer hose
if vehicle is fitted with it, as well as unclipping
the harness and hose from the plastic.
Clamp the washer hose at the vehicle side to
prevent the system draining.
RHS SHOWN
STEP 4
LHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 6 of 27
04/08/2023
6. Apply masking tape to the vehicle bumper,
just beneath the grille to protect it from the
trim removal tool used in the following step.
7. Insert a thin trim removal tool between the
grille and bumper at the locations indicated
opposite to release the clips securing the
grille to the bumper.
ONLY LOWER GRADE VEHICLES (CORE,
LIFE, STYLE) UTILISE THE 6 CENTRE CLIPS.
ALL VARIANTS HAVE 3 CLIPS PER SIDE
UNDER THE HEADLIGHTS
8. Pull the grille forward from the vehicle to
remove it. Use trim removal tools to carefully
pry high grade bumpers, if necessary.
Take care as the clips which connect the
grille to the bumper are a molded part of the
grille & the clips can break easily if proper
care is not taken.
Place masking tape over 360-Degree
Camera if present to protect it.
9. Remove and discard the newly exposed
upper bumper clips (3) and bolts (2).
10. Remove and discard the screws (2) securing
the lower bumper to the vehicle and flare.
Repeat on LHS.
RHS SHOWN
LOWER GRADE
BUMPERS ONLY
ALL VEHICLE GRADES
RHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 7 of 27
04/08/2023
11. Remove and discard the clips (4) securing
the flare to the bumper.
12. Unclip the flare from the bumper.
13. Remove the 3 scrivets securing the inner
guard to the bumper.
Repeat LHS
14. Remove and retain the 3 scrivets securing
the cover panel inside the wheel arch to gain
access to the screws securing the bumper to
fender.
15. Remove and discard screws (3) securing the
bumper to the fender.
16. Unclip the bumper from the fender.
Repeat LHS
STEP 17 IS FOR VEHICLES WITH PARK
ASSIST SENSORS ONLY.
17. Unclip the parking sensor from the flare.
Unplug the sensor from the harness and note
the sensor’s location and direction and set
aside.
Repeat LHS
LHS SHOWN
RHS SHOWN
CLIP

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 8 of 27
04/08/2023
18. Disconnect the main plug and unclip harness
from vehicle.
19. Carefully remove the bumper and set aside.
20. Remove and discard the clips (2) securing
the foam to the intrusion beam.
21. Remove and discard foam.
USE EXTREME CAUTION IN HANDLING THE
RADAR. DAMAGE CAUSED BY
MISHANDLING IS NOT WARRANTABLE!
22. Remove the radar cover by remove the clips
(2).

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 9 of 27
04/08/2023
23. Unplug the radar and unclip the harness from
the radar mount and intrusion beam.
24. Remove and discard the front intrusion beam
by removing and retaining the front intrusion
beam fasteners (6) from the indicated
locations.
25. Remove and discard the fasteners (3)
securing the radar bracket to the intrusion
beam. Carefully set aside radar.

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 10 of 27
04/08/2023
26. Remove and discard the bumper support
bracket by removing the screws (3). Retain 1
screw for use later.
Repeat on LHS.
27. On the right-hand side only refit the horn
bracket back to the vehicle using the retained
screw. Loosen the outer horn mount and
rotate 180°. Loosen the outer horn and rotate
so that the plug is vertical as shown below.
Tighten.
28. Remove and retain the OE Front Underbody
Guard and associated fasteners (4).
RHS SHOWN
RETAIN
STEP 26
STEP 26

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 11 of 27
04/08/2023
29. Before removing the recovery points, firstly
support the underneath of the radiator using
a stand or any other method.
30. Remove and discard the recovery point:
30.1. Remove and discard the fastener
(1) securing the air dam to the
recovery point.
30.2. Remove and retain the fasteners
(2) securing the recovery point to
the chassis.
Repeat on LHS.
31. Position the “Inner Chassis Plate” (F-33803)
on the inner face of the chassis rail (as
shown), then loosely secure it in place, using
M12 x 1.25 x 35mm Hex Head Bolt (1), 1/2”
x Ø1-1/4” x 2.5mm Flat Washer (2) & M12 x
1.25 Nyloc Nut (1).
32. Align the holes underneath the chassis and
ensure that the plate is hard up against the
underside of the chassis, then tighten the
previously installed fastener to the relevant
torque settings listed on Page 4.
Repeat on LHS.
RHS SHOWN
STEP 30.1
STEP 30.2
RHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 12 of 27
04/08/2023
33. Loosely secure the “UBG Mount Assembly”
(F-34111) to the underneath of the chassis
using the OE Fasteners retain in Step 30.2.
Ensure that the radiator rubber mount is
sitting through the slot and that the air dam
is in front of the mount.
34. Loosely secure the air dam to the “UBG
Mount Assembly” using M6 x 1.0 x 20mm
Hex Head Bolt (1), M6 x Ø18mm x 1.6mm
Flat Washer (2) & M6 x 1.0 Nyloc Nut (1).
Repeat on LHS.
35. Remove the screws (2) and scrivets (4) to
allow the air dam to be pulled away from the
body to be able to trim. Trim the air dam
along the previously marked lines.
36. Using the indicated vertical edge of the air
dam as a reference, cut through the centre
piece of the air dam.
Repeat on LHS.
37. Discard the centre piece, and then reattach
the newly trimmed piece back to the vehicle
using the previously removed screws (2).
RHS SHOWN
RHS SHOWN
SCREW
SCRIVET

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 13 of 27
04/08/2023
38. Unclip the main plug harness from the top
plastic panel and unplug the bonnet latch
plug.
39. Feed down between the radiator and plastic
surround as shown.
Plug the bonnet plug back in then zip tie the
harness along the plastic surround.
40. Run a 10.5mm drill bit through the top and
bottom inner front chassis holes as shown.
Treat newly exposed material with a rust
preventative.
Repeat on LHS.
41. Position the “Winch Frame” (F-33821) on the
vehicle chassis rail ends then loosely secure it
in place using the 6 fasteners retained in
Step 24.
THE WINCH FRAME SHOULD FIT ON THE
OUTSIDE OF THE PREVIOUSLY INSTALLED
UBG MOUNT.
42. Secure “Winch Frame” loosely using M10 x
1.25 x 30mm Hex Head Bolt (4), M10 x
Ø30mm x 3.0mm Flat Washer (8) & M10 x
1.25 Nyloc Nut (4).
RHS SHOWN
STEP 41
STEP 42
RHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 14 of 27
04/08/2023
43. Loosely secure the “Wing Guard Mount” (F-
34107) to the “Winch Frame” using M12 x
1.25 x 40mm Hex Head Bolt (2), 1/2” x Ø1-
1/4” x 2.5mm Flat Washer (4) & M12 x 1.25
Nyloc Nut (2).
Repeat on LHS.
44. Loosely secure the “Winch Frame” to the
“Inner Chassis Plate” using M10 x 1.25 x
30mm Hex Head Bolt (2), M10 x Ø21mm x
2.0mm Flat Washer (4) & M10 x 1.25 Nyloc
Nut (2).
Repeat on LHS.
45. Centre the “Winch Frame” to the vehicle by
measuring diagonally from mount tip to
headlamp corner as shown, equalize sizes as
close as practical.
46. Tension the fasteners from Steps 41 to 44,
then Steps 33 & 34 to the relevant torque
settings listed on Page 4.
RHS SHOWN
RHS SHOWN
WING GUARD
MOUNT

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 15 of 27
04/08/2023
47. Fit “Bending Angle” (F-33948) to inboard
face of “Winch Frame”and “Washer Plate”
(F-32863) to front using M12 x 1.25 x 35mm
Hex Head Bolt (3), 1/2”x Ø1-1/4” x 2.5mm
Flat Washer (6) & M12 x 1.25 Nyloc Nut (3).
FIT M12 BOLT ASSEMBLY WITH BOLT HEAD
ON FRONT FACE.
48. Align plate with existing holes and tighten to
specified torque. Check holes and slots align
after tightening to allow easy bolt
fitment/clearance.
Repeat on LHS.
STEP 49 ONLY APPLIES IF A WINCH IS TO
BE FITTED. OTHERWISE PLEASE PROCEED
TO NEXT STEP.
49. Refer to the winch fitting instructions to fit
the winch to the “Winch Frame”.
At this stage, DO NOT FASTEN THE WINCH
TO THE WINCH FRAME, ONLY PLACE WINCH
IN POSITION.
50. Fit the parker/indicator supplementary wiring
harness ( Purchased Separately ) to the
vehicle loom as per instructions. Temporarily
plug in supplied parker/indicator light. Check
the operation then disconnect the light
assemblies.
NUTS
TO INSIDE!
Holes must
align
RHS SHOWN
RHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 16 of 27
04/08/2023
STEP 51 IS FOR VEHICLES FITTED WITH 360-
DEGREE CAMERA ONLY.
51. Remove the OE 360-degree camera from the
rear of the grille badge by removing the
screw and clips securing the harness and
washer hose.
52. Looking at the bumper from the rear, record
each parking sensor’s position and
orientation.
53. Remove the parking sensors and the
associated wiring harness from the bumper.
54. Remove the foglight surrounds from the
bumper
55. Cut the centre of the bumper along a straight
line just above the lower centre garnish.
FOR HIGH GRADE BUMPERS
(AVENTURA/PANAMERICANA) ENSURE THE
CUT IS BENEATH THE INDICATED CLIPS
RECORD ORIENTATION
OF CONNECTORS
RHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 17 of 27
04/08/2023
56. Pull the flare away from the vehicle and trim
along the line previously marked with the
bumper cut template.
Be careful not to break the clips securing the
flare to the fender as they are very fragile.
57. Repeat on RHS.
58. Cut the bumper along the trim lines
previously marked with the bumper cut
template and remove the lower portion.
59. Fit the bumper and grille back to the vehicle
using the fasteners (2) retained in Step 4.
60. Using clips retained in Step 11, reclip the
flare to the bumper and ensure the bumper
does not hang below the flare.
61. Attach pinch weld to the cut bumper edges,
as shown. Trim any excess.
LHS SHOWN
RHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 18 of 27
04/08/2023
62. Clean mountings surfaces so they are free of
oils & residues, then affix the parking sensor
housings to the rear side of the “T13 Outback
Bar” (F-33910) ensuring that the orientation
is as noted in Step 52.
If vehicle is not fitted with parking sensors at
any of the locations, affix the supplied
parking sensor housings without pressing
out the blanking circle.
STEPS 63 TO 65 IS FOR VEHICLES WITH
PARK ASSIST SENSORS ONLY.
63. Press out the blanking from the front of the
parking sensor housing, deburr surface and
insert the parking sensor.
64. Secure the parking sensor retaining plate to
the parking sensor housing using the
supplied 8g x 25mm pan head screws.
65. Apply the supplied 1.2mm (thicker) double
sided sticker to the front face of the parking
sensor housing.
66. Secure the camera to the “Camera Mount”
(F-34199) using the “Camera Clamp” (F-
34200), “Foam Tape” (2x 25mm), M6 x 1.0 x
20mm Hex Head Bolt (1), M6 x Ø12.5mm x
1.2mm Flat Washer (2) & M6 x 1.0 Nyloc Nut
(1). Place the “Foam Tape” between the
camera and the “Camera Clamp”.
RHS SHOWN

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 19 of 27
04/08/2023
67. Secure the “Camera Mount” to the “T13
Outback Bar” using M6 x 1.0 x 20mm Button
Head Bolt (2), M6 x Ø12.5mm x 1.2mm Flat
Washer (2) & M6 x 1.0 Nyloc Nut (2). Use
washer on nut side only. Nuts are to be on
“Camera Mount” side.
If a Foglight Kit has been purchased,
install it now referring to the instructions
provided in the kit. Otherwise, follow the
below steps to install the provided
Foglight Blanking Cover.
1. Sandwich the foglight mounting bracket
between Foglight Washer Plates (2).
2. Position the Foglight Blanking Cover as
shown opposite.
68. Using M6 x 1.0 x 2.0 Hex Head Screws (4),
M6 x Ø12.5mm Flat Washers (4) and M6 x
1.0 Flange Nuts (4), secure the Foglight
Blanking Cover to the FPS.
69. Feed the sensor loom through the left bar
mount at the top though to the right bar
mount and attach to bar using zip ties.
STEP 1
STEP 2
RHS SHOWN
ROUTE HARNESS FROM
LEFT TO RIGHT THROUGH
UPPER HOLES

FITTING INSTRUCTIONS
Product:
T13 Outback Bar
Vehicle:
Volkswagen Amarok
Part No.
070SB13N83X
For product warranty please refer to our website www.tjm.com.au
F-37030.docx
Page 20 of 27
04/08/2023
70. Fit the “M8 Pull Plunger w/ Thin Nut” (F-
33789) to the “T13 Outback Bar” and tighten
the thin nut against the weld nut to lock the
pull plunger in place.
Ensure that the pin is just protruding through
the number plate mount.
71. With the assistance of another person,
carefully lift the “T13 Outback Bar” into
position on the “Winch Frame”, then loosely
secure it in place, using supplied “Sliding
Washer Plate” (F-34019) and M12 x 1.25 x
40mm Hex Head Bolt (4), 1/2" x Ø1-1/4" x
2.5mm Flat Washer (8) & M12 x 1.25 Nyloc
Nut (4) at the indicated locations.
Repeat on LHS.
72. Align the FPS to the vehicle so that the guard
clearance is 20 - 25mm, and the end of the
FPS is in line with the wheel arch.
73. Tighten all the fasteners to the relevant
torque settings listed on Page 4.
RHS SHOWN
RHS ONLY
20 - 25mm
RHS SHOWN